Samsung AR12MSPXAWKNEU manual Accessories in the outdoor unit package, Tools General tools

Page 7

If using a multi system, refer to the manual supplied with the outdoor unit.

Optional accessories

 

Insulated assembly pipe,

Insulated assembly pipe,

Ø 9.52 mm (1)

Ø 6.35 mm (1)

**09*******

 

**12*******

Insulated assembly pipe,

Insulated assembly pipe,

Ø 12.70 mm (1)

Ø 15.88 mm (1)

**18*******

**24*******

Pipe clamp B (3)

Pipe clamp A (3)

Drain Hose, 2 m long (1)

Foam Insulation (1)

Vinyl tape (2)

PE T3 foam tube insulation (1)

Putty 100 g (1)

Drain plug (1)

M4 x 25 tapped screw (6)

Cement nail (6)

3-wire Power Cable (1)

3-wire Assembly Cable (1)

2-wire Assembly Cable (1)

 

Accessories in the outdoor unit package

Rubber leg (4)

NOTE

A flare nut is attached to the end of each pipe of an evaporator or a service port. Use flare nuts when connecting the pipes.

Wire assembly cables are optional. If they are not supplied, use standard cables.

The drain plug and the rubber legs are included only when the air conditioner is supplied without assembly pipes.

If these accessories are supplied, they are in the accessory package or outdoor unit package.

Tools

General tools

Vacuum pump

(Backward flowing prevention)

Manifold gauge

Stud finder

Torque wrench

Pipe cutter

Reamer

Pipe bender

Spirit level

Screwdriver

Spanner

Drill

L-wrench

Measuring tape

Tools for test operation

Thermometer

Resistance meter

Electroscope

English 7

Installation

Image 7
Contents Air conditioner Contents General information Safety Information on Installation Fires, explosions or injuries Install the unit in a place where water can drain smoothlyCases Choosing the installation locationPreparation Minimum clearances for the outdoor unitAccessories in the indoor unit package AccessoriesUnit mm Thermometer Resistance meter Electroscope English Accessories in the outdoor unit packageTools General tools Tools for test operationTaping the pipes, cables, and drain hose Drilling a hole through the wallRemove the cap screws, then the screws Indoor Unit InstallationInstallation plate Disassembling the cover panelConnecting the Power and communication cables assembly cable Compression dimension should be Optional Extending the power cableFire Installing and connecting the drain hoseInstall the drain hose Optional Extending the drain hoseOptional Changing the direction of the drain hose Pass the pipe through the hole in the wall Shortening or extending the refrigerant pipes assembly pipeWhen fixing the indoor unit on a wall 10 Fixing the installation plateWhen fixing the indoor unit on a window frame 12 Assembling the cover panel 11 Fixing the indoor unit to the installation plateWhen fixing the indoor unit on a gypsum board Fix the installation plate without inclining to one sideThat the fan can operate correctly Outdoor Unit InstallationFixing the outdoor unit in place Refrigerant pipesEvacuating the air Leave the system in the standby modeCooling capacity and malfunction. Use a vacuum pump Siphon Adding refrigerant①+②, c Running the Smart Install mode Installation InspectionBlocking error Open Error betweenPower cable or communication Motor Connector Remove foreign substance. CheckLet the compressor run for more than 5 minutes Check the following Strength of the installation sitePerforming final check and trial operation Pumping down for removing the productAttach the Sub PCB to the Case Sub PCB Sub PCB installationoptionalAssemble the Case Sub PCB to the indoor unit DB68-06732A-03
Related manuals
Manual 2 pages 25.92 Kb Manual 39 pages 32.94 Kb Manual 25 pages 2.73 Kb Manual 36 pages 15.94 Kb Manual 36 pages 60.74 Kb Manual 36 pages 44.82 Kb Manual 36 pages 4.31 Kb Manual 25 pages 23.47 Kb Manual 36 pages 14.89 Kb Manual 36 pages 10.71 Kb Manual 25 pages 19.68 Kb Manual 25 pages 63.09 Kb