Maintaining the air conditioner

Samsung AQV18YWAN, AQV12KBAN, AQV12YWAN manual Maintaining the air conditioner, Periodical checks

Page 21

If the air conditioner will not be used for an extended period of time, dry the air conditioner to maintain it in best condition.

1.Dry the air conditioner thoroughly by operating in Fan mode for 3 to 4 hours and disconnect the power plug. There may be internal damage if moisture is left in components.

2.Before using the air conditioner again, dry the inner components of the air conditioner again by running in Fan mode for 3 to 4 hours. This helps remove odors which may have generated from dampness.

ENGLISH

Periodical checks

Refer to the following chart to maintain the air conditioner properly.

Type	Description	Every 2	Every 3	Every 4	Once a year
Type	Description	weeks	months	months	Once a year
		weeks	months	months

	Clean the Full HD filter (1)	

Indoor	Clean the condensate drain pan (2)				

	Thoroughly clean the heat exchanger (2)				
unit	Thoroughly clean the heat exchanger (2)				
unit
	Clean the condensate drain pipe (2)			

	Replace the remote controller batteries (1)				

	Clean the heat exchanger on the outside of the unit (2)			

	Clean the heat exchanger on the inside of the unit (2)				

	Clean the electric components with jets of air (2)				
Outdoor
Outdoor	Verify that all the electric components are firmly				
unit	tightened (2)				
unit	tightened (2)

	Clean the fan (2)				

	Verify that all the fan assembly is firmly tightened (2)				

	Clean the condensate drain pan (2)				

: This check mark requires checking the indoor/outdoor unit periodically. Follow the description to maintain the air conditioner properly.

(1) The described operations should be performed more frequently if the area of installation is very dusty.

(2) These operations must always be performed by qualified personnel. For more detailed information, see the installation part in the manual.

AQV09K&Y@@_Jungfrau_IBIM_E_32448A.indd 21

2011-3-19 15:45:15

Image 21

Contents

AQV09K&Y@@JungfrauIBIME32448A.indd 2011-3-19 Contents Important safety symbols and precautions Safety precautionsFollow directions Wall socketFor Using For Cleaning Checking before use Operation rangesModel RJ Checking the name of the parts Main partsDisplay Remote controller buttons Checking the remote controllerBattery changing time Remote controller displayStoring the remote controller Inserting the batteriesBasic function Press Button to adjust the temperatureUsing the Turbo function Adjusting the air flow directionPress the Air swing button on the remote controller Vertical air flowPress the button on the remote controller When the air conditioner is on and in cool/heat modePress the Set/Cancel button to active it ModeSetting the On/Off timer Setting the Current timeFollow the same process for setting on timer and off timer Additional options available in On timer modeUsing the SPi function Using the Smart Saver functionUsing the dlight Cool function Using the Auto Clean functionWhen the air conditioner is turned on Cancel Press the Auto clean button once againYou can reduce the noise generated from an indoor unit UsingAA the Quiet functionCleaning the outdoor unit heat exchanger Cleaning the indoor unitOpening the panel Heat exchangerCleaning the Full HD filter Cleaning the air conditionerRemoving the Full HD filter Dry the Full HD filter in a ventilated areaPeriodical checks Maintaining the air conditionerTroubleshooting All blink Error is indicatedNoise is generated Outdoor unitIncluded Models Remark General informationInstalling the unit Choosing the installation locationPower supply line, fuse or circuit breaker  a place where the air filter can be replaced easilyWhere sulfide gas exists Outdoor UnitModel When installing more than 1 outdoor unit When installing 1 outdoor unitSpace Requirements for Outdoor Unit Side viewAccessories in the indoor unit case AccessoriesAccessories in the outdoor unit case Unit mmOptional accessories Fixing the installation plateTools required for installation General Tools Tools for test operationsConnecting the assembly cable Cable specificationConnecting the cable Each wire is labeled with the corresponding terminal number Extend the assembly cable if necessaryCut off the remaining foam insulation Smooth the cut edgesCutting or extending the pipe Purging the indoor unitUnscrew the caps at the end of each pipe Put a flare nut slightly into the pipe and modify the flareCorrect Inclined Pipe 50 Pa. The joint must be accessible and serviceableCracked Outer DiameterDrain hose installation Connect a drain hose to the drain plug Purging the connected pipesDrain hole Drain plug Drain hose Ensure that condensation draining is adequateAdding Refrigerant Gas service port as seen in the pictureIf you use a pipe longer than 5m If you use a pipe shorter than 5mPlease fill in with indelible ink  the factory refrigerant charge of the product1975 To check for gas leaks on the outdoor unit Performing the gas leak testsTo check for gas leaks on the indoor unit Leak test with nitrogen before opening valvesFixing the indoor unit in place Then place the indoor unit on the installation plateFixing the outdoor unit in place 612Final Check and Trial Operation Apply heat to the contraction tube to contract it How to connect your extended power cablesAfter tube contraction work is completed, wrap it with Insulation tape to finishWried remote controller, central remote controller etc Sub PCB installationoptional Only for multi systemQuestions or COMMENTS? Air Conditioner

Related manuals

Samsung AQV18YWAN, AQV12KBAN, AQV12YWAN manual Maintaining the air conditioner, Periodical checks