Samsung SSA-P400/EXP, SSA-P400T/EXP manual Cable Selection, Host P.C

Page 12

product introduction

CABLE SELECTION

RS-232	RS-422/RS-232
	Converter
	Converter

HOST P.C.

RS-422

RS-422		RS-422

DC12V

Power Supply

DC12V Power Supply

X Y Z

[\ ] ^ _ `

lzj W lu{

i

X Y Z

[\ ] ^ _ `

lzj W lu{

i

RF Reader	Lock/Alarm	RF Reader	Lock/Alarm
Exit Button/Sensor Input		Exit Button/Sensor Input

		Item		Cable Type

	1	Power (DC12V)	Belden #9409, 18 AWG 2 Conductor, Unshielded
	1	DC Power Device	Belden #9409, 18 AWG 2 Conductor, Unshielded

	2	Reader (power and data)	Belden #9512, 22 AWG 4 Conductor, Shielded
	2	Reader (power and data)
		External reader Device	Belden #9514, 22 AWG 8 Conductor, Shielded
			Belden #9514, 22 AWG 8 Conductor, Shielded

		Door Contact Sensor	Belden #9512, 22 AWG	4 Conductor, Shielded
	3	Exit Button	Belden #9512, 22 AWG	4 Conductor, Shielded
		Exit Button
		Sensor Input	Belden #9514, 22 AWG	8 Conductor, Shielded
		Sensor Input
		Input Device
		Input Device
	4	Door Lock
	4	Alarm Device	Belden #9409, 18AWG	2 Conductor, Unshielded
		Lock (Alarm) Device
	5	RS-232 Cable	Belden #9829, 24 AWG	2-twisted pair, Shielded
	5	Converter Host P.C.	Belden #9829, 24 AWG	2-twisted pair, Shielded
		RS-485 Cable
		Device Device	Belden #9829, 24 AWG	2-twisted pair, Shielded
	6	Device Converter
	6	RS-422 Cable
		RS-422 Cable
		Device Device	Belden #9830, 24 AWG	3-twisted pair, Shielded
		Device Converter

J The cables should be thick enough to allow the maximum current consumed by the reader.

12_ product introduction

Image 12

Contents Access Control Panel Please visit our websiteSafety information Safety informationImportant Safety Instructions Contents Features Product introductionInput Port Format Setup Door Open Alarm and Forced Door Open AlarmSettings Holiday SetupWHAT’S Included Main UnitCD Manual Board ID Setup SwitchSwitch System after the initialization Output Relay #1 ~ Address Setup 5V for any output occurrence SwitchIndicatoradditionally Input LED IndicatorSignal occurs Buzzer control settingsConnector used to connect to the main board BoardInput port #8 Input port #9Input port #10 Input port #11Cable Selection Host P.CConnecting the Termination Resistor and Diode Termination ResistorBypass Diode Connection Termination Resistor in RS-485 CommunicationInstallation and external connection EARTH-GROUNDING the Communication CablesPOWER, READER, and I/O Connection Power ConnectionReader Connection Input Connection Exit Button Connection Input #1, Input #3Output Connection DC +12V GNDCommunication Line Connection RS-232 Communication Port ConnectionHost PC Check the location of the communication portRS-422 Communication Port Connection Standalone HostTX+ RX+RS-422 Communication Port Connection Multiple Units TX+ RX+TCP/IP Communication Port Connection HUB TCP / IPTCP/IP Communication Conﬁguration TCP/IP ConnectionInitializing the system using the Initialize switch Switches simultaneouslyInitialization System InitializationBoard ID Setting You can specify between 0 and 255 for the board IDTroubleshooting TroubleshootingProblem Action Problem When the system is in sync withNo communication is available Product Specifications Product speciﬁcationsCorrect disposal of batteries in this product

Related manuals

Manual 80 pages 17.65 Kb