Samsung SSA-P400T/EXP, SSA-P400/EXP manual Important Safety Instructions

Page 3

5.Keep out of direct sunlight and heat radiation sources. It may cause fire.

6.Install it in a place with good ventilation.

7.Avoid aiming the controller directly towards extremely bright objects such as sun.

8.Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

9.The Mains plug is used as a disconnect device and shall stay readily operable at any time.

FCC Statement

Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note : This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

SAFETY INFORMATION

IMPORTANT SAFETY INSTRUCTIONS

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with

the apparatus.

13. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

English _ 3

Image 3
Contents Please visit our website Access Control PanelSafety information Safety informationImportant Safety Instructions Contents Product introduction FeaturesHoliday Setup Input Port Format SetupDoor Open Alarm and Forced Door Open Alarm SettingsWHAT’S Included Main UnitCD Manual Address Setup 5V for any output occurrence Switch Board ID SetupSwitch Switch System after the initialization Output Relay #1 ~Buzzer control settings IndicatoradditionallyInput LED Indicator Signal occursBoard Connector used to connect to the main boardInput port #11 Input port #8Input port #9 Input port #10Host P.C Cable SelectionTermination Resistor in RS-485 Communication Connecting the Termination Resistor and DiodeTermination Resistor Bypass Diode ConnectionEARTH-GROUNDING the Communication Cables Installation and external connectionPOWER, READER, and I/O Connection Power ConnectionReader Connection Exit Button Connection Input #1, Input #3 Input ConnectionDC +12V GND Output ConnectionCheck the location of the communication port Communication Line ConnectionRS-232 Communication Port Connection Host PCRX+ RS-422 Communication Port Connection StandaloneHost TX+TX+ RX+ RS-422 Communication Port Connection Multiple UnitsTCP/IP Connection TCP/IP Communication Port ConnectionHUB TCP / IP TCP/IP Communication ConfigurationSystem Initialization Initializing the system using the Initialize switchSwitches simultaneously InitializationYou can specify between 0 and 255 for the board ID Board ID SettingTroubleshooting TroubleshootingProblem Action Problem When the system is in sync withNo communication is available Product specifications Product SpecificationsCorrect disposal of batteries in this product
Related manuals
Manual 80 pages 17.65 Kb