Samsung SSA-P400/EXP, SSA-P400T/EXP manual Safety information

Page 2

safety information

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.

This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING

To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.

WARNING

1.Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product.

2.Incorrectly connecting the power supply or replacing battery may cause explosion, fire, electric shock, or damage to the product.

3.Do not connect multiple controllers to a single adapter. Exceeding the capacity may cause abnormal heat generation or fire.

4.Securely plug the power cord into the power receptacle. Insecure connection may cause fire.

5.When installing the controller, fasten it securely and firmly. The fall of controller may cause personal injury.

6.Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the controller. Doing so may cause personal injury due to fire, electric shock, or falling objects.

7.Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock.

8.If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock.

9.If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.)

10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock.

CAUTION

1.Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference.

2.Do not install in a location subject to high temperature (over 50°C), low temperature (below 0°C), or high humidity. Doing so may cause fire or electric shock.

3.If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it.

4.Remove the power plug from the outlet when there is a lighting storm. Neglecting to do so may cause fire or damage to the product.

2_ safety information

Image 2
Contents Access Control Panel Please visit our websiteSafety information Safety informationImportant Safety Instructions Contents Features Product introductionSettings Input Port Format SetupDoor Open Alarm and Forced Door Open Alarm Holiday SetupCD Manual WHAT’S IncludedMain Unit Switch System after the initialization Output Relay #1 ~ Board ID SetupSwitch Address Setup 5V for any output occurrence SwitchSignal occurs IndicatoradditionallyInput LED Indicator Buzzer control settingsConnector used to connect to the main board BoardInput port #10 Input port #8Input port #9 Input port #11Cable Selection Host P.CBypass Diode Connection Connecting the Termination Resistor and DiodeTermination Resistor Termination Resistor in RS-485 CommunicationInstallation and external connection EARTH-GROUNDING the Communication CablesReader Connection POWER, READER, and I/O ConnectionPower Connection Input Connection Exit Button Connection Input #1, Input #3Output Connection DC +12V GNDHost PC Communication Line ConnectionRS-232 Communication Port Connection Check the location of the communication portTX+ RS-422 Communication Port Connection StandaloneHost RX+RS-422 Communication Port Connection Multiple Units TX+ RX+TCP/IP Communication Configuration TCP/IP Communication Port ConnectionHUB TCP / IP TCP/IP ConnectionInitialization Initializing the system using the Initialize switchSwitches simultaneously System InitializationBoard ID Setting You can specify between 0 and 255 for the board IDProblem Action TroubleshootingTroubleshooting No communication is available ProblemWhen the system is in sync with Product Specifications Product specificationsCorrect disposal of batteries in this product
Related manuals
Manual 80 pages 17.65 Kb