Samsung SSA-S2000/EXP manual Important Safety Instructions

Page 3

8.Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

9.The Mains plug is used as a disconnect device and shall stay readily operable at any time.

FCC Statement

Caution : Any changes or modifications in construction of this device which are not expressly approved by the

party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1)This device may not cause harmful interference, and

2)This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, any cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT SAFETY INSTRUCTIONS

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

13. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

SAFETY INFORMATION

English _ 3

Image 3
Contents Imagine the possibilities Standalone Rfid Access ControllerSafety information Safety informationThis device may not cause harmful interference, Important Safety InstructionsContents Contact Sensor alarm To specify the input mode for AUXTo specify the input mode for the Door To specify the use of the tamper alarmProduct introduction FeaturesWHAT’S Included Quick Guide Rings Diodes UF4004, 1N4001~4007Master Card Cables Front View AT a GlanceCable Color Scheme Installation and external connection DC12V Cable SelectionConnection Bypass Diode ConnectionOutput Connection External Reader Connection Initialization Basic OperationsIf you press the Exit button, the door will be opened TTL Output Chime Bell Output Wiegand Output SetupInitialization Brown line with white stripesHardware Forcible Initialization Forced Initialization with External LineReader mode setup Reader Mode Setup RF onlyNo Master Card or Master PIN is ever registered Reader Mode Setup RF + P/W Reader Mode Setup PIN onlyPress Button 0 and Button Reader Mode Setup RF/PIN Combination Mode Enabling Keypad Input for the Card NumberButton Sequence, and press ENT To Register Cards in RF only Mode User managementRegistering Cards in a Combination of RF and P/W Modes To Register Cards in PIN Mode Registering Cards in RF Card / PIN Combination ModeMaster PIN To Delete a Registered Card or PIN Number Basic setup Duress AlarmTo Specify the Retry Count for AN Unregistered ID  See the table below for your reference To Specify the Delayed Start Time in Secure ModeTo Specify the Limited Time for the Keypad Input To Specify the Operation Time of the Door Contact SensorTo Open or Close the Entry Door To Specify the Alarm Output Port for the Dismantled DeviceButtons and press ENT To SET or Release the Quick ModeTo SET or Release the Toggle Mode for the Door Relay Default is set to not usedTime setup To Specify the Output Time if the Card is AuthenticatedYou can specify from 10 to To Specify the Duress TTL Output To Specify the Output Time if the Card is not AuthenticatedEnter the two-digit TTL relay output time and press ENT To Specify the Alarm Operation Time for AUX32 I/O time setup \ `  The default is set to use the chime bell Advanced settingTo Specify the TTL Output Operation Mode  The default is set to switch from HIGH5V to LOW0VTo Specify the Chime Bell Operation Time To Specify the Input Mode for AUXAdvanced setting To Specify the Input Mode for the Door Contact Sensor To Specify the Input Mode for the Exit ButtonAdditional features To Specify the USE of the Tamper AlarmMute To Check the Output Specified for AN Unregistered Card User To Check the Output Specified for a Registered Card UserTo Check the Output Specified for AUX Additional Features Other information Initial ValuesThis product operates in the following initial values Function Codes Sense if AUX 2 switches from H to L Sense if AUX 1 switches from L to HSense if AUX 1 switches from H to L Sense if AUX 2 switches from L to HTroubleshooting Troubleshooting√ RF Only Check the operation status of the product √ Enter the command to delete the user 14 + ENTService center EInstall and use the product as usualCIf SSA-S2000 responds when you press the Exit button Using the keypadUnregistered numbers in 5 consecutive times default User cards to the factory defaultConsult with a qualified technician Irrelevant data is transferredDisconnection or short-circuit SSA-S200087.0 x 109.0 x Product SpecificationsWeight 220g Product specificationsCorrect disposal of batteries in this product