Samsung SSA-S2000/EXP manual Additional Features

Page 41

TO CHECK THE OUTPUT SPECIFIED FOR AUX 2

You can check the output setting that you speciﬁed in “To specify the alarm operation time for AUX 2”. (See page 32.)

1.Present the Master Card to the device.

	X	Y	Z
2. Press Button 3 and Button 6 in sequence and press ENT .		\	]
			`
tGj	lzj	W	lu{
	lzj	W	lu{
	i
			zzhTzYWWW
	X	Y	Z
		\	]
	^	_	`
	lzj	W	lu{
	i
			zzhTzYWWW

ADDITIONAL FEATURES

TO CHECK THE OUTPUT SPECIFIED FOR AUX 3

You can check the output setting that you speciﬁed in “To specify the alarm operation time for AUX 3”. (See page 32.)

1. Present the Master Card to the device.

	X	Y	Z
2. Press Button 3 and Button 7 in sequence and press ENT .		\	]
2. Press Button 3 and Button 7 in sequence and press ENT .			`
			`
tGj	lzj	W	lu{
	lzj	W	lu{
	i
			zzhTzYWWW
	X	Y	Z
		\	]
	^	_	`
	lzj	W	lu{
	i
			zzhTzYWWW

English _ 41

Image 41

Contents Imagine the possibilities Standalone Rfid Access ControllerSafety information Safety informationThis device may not cause harmful interference, Important Safety InstructionsContents To specify the input mode for the Door To specify the input mode for AUXTo specify the use of the tamper alarm Contact Sensor alarmProduct introduction FeaturesMaster Card Cables WHAT’S IncludedQuick Guide Rings Diodes UF4004, 1N4001~4007 Front View AT a GlanceCable Color Scheme Installation and external connection DC12V Cable SelectionConnection Bypass Diode ConnectionOutput Connection External Reader Connection If you press the Exit button, the door will be opened InitializationBasic Operations Initialization Wiegand Output SetupBrown line with white stripes TTL Output Chime Bell OutputHardware Forcible Initialization Forced Initialization with External LineNo Master Card or Master PIN is ever registered Reader mode setupReader Mode Setup RF only Press Button 0 and Button Reader Mode Setup RF + P/WReader Mode Setup PIN only Button Sequence, and press ENT Reader Mode Setup RF/PIN Combination ModeEnabling Keypad Input for the Card Number Registering Cards in a Combination of RF and P/W Modes To Register Cards in RF only ModeUser management Master PIN To Register Cards in PIN ModeRegistering Cards in RF Card / PIN Combination Mode To Delete a Registered Card or PIN Number To Specify the Retry Count for AN Unregistered ID Basic setupDuress Alarm  See the table below for your reference To Specify the Delayed Start Time in Secure ModeTo Specify the Limited Time for the Keypad Input To Specify the Operation Time of the Door Contact SensorTo Open or Close the Entry Door To Specify the Alarm Output Port for the Dismantled DeviceTo SET or Release the Toggle Mode for the Door Relay To SET or Release the Quick ModeDefault is set to not used Buttons and press ENTYou can specify from 10 to Time setupTo Specify the Output Time if the Card is Authenticated To Specify the Duress TTL Output To Specify the Output Time if the Card is not AuthenticatedEnter the two-digit TTL relay output time and press ENT To Specify the Alarm Operation Time for AUX32 I/O time setup \ ` To Specify the TTL Output Operation Mode Advanced setting The default is set to switch from HIGH5V to LOW0V  The default is set to use the chime bellTo Specify the Chime Bell Operation Time To Specify the Input Mode for AUXAdvanced setting To Specify the Input Mode for the Door Contact Sensor To Specify the Input Mode for the Exit ButtonMute Additional featuresTo Specify the USE of the Tamper Alarm To Check the Output Specified for AN Unregistered Card User To Check the Output Specified for a Registered Card UserTo Check the Output Specified for AUX Additional Features This product operates in the following initial values Other informationInitial Values Function Codes Sense if AUX 1 switches from H to L Sense if AUX 1 switches from L to HSense if AUX 2 switches from L to H Sense if AUX 2 switches from H to LTroubleshooting Troubleshooting√ RF Only Service center √ Enter the command to delete the user 14 + ENTEInstall and use the product as usual Check the operation status of the productUnregistered numbers in 5 consecutive times default Using the keypadUser cards to the factory default CIf SSA-S2000 responds when you press the Exit buttonDisconnection or short-circuit Irrelevant data is transferredSSA-S2000 Consult with a qualiﬁed technicianWeight 220g Product SpecificationsProduct speciﬁcations 87.0 x 109.0 xCorrect disposal of batteries in this product