Samsung SSA-S2000/EXP manual To Check the Output Specified for AUX

Page 40

additional features

TO CHECK THE OUTPUT SPECIFIED FOR THE DOOR CONTACT SENSOR ALARM

You can check the output setting that you speciﬁed in “To specify the alarm output for an input error of the Door contact Sensor”. (See page 31.)

1. Present the Master Card to the device.

	X	Y	Z
2. Press Button 3 and Button 4 in sequence and press ENT .		\	]
2. Press Button 3 and Button 4 in sequence and press ENT .			`
			`
tGj	lzj	W	lu{
	lzj	W	lu{
	i
			zzhTzYWWW
	X	Y	Z
		\	]
	^	_	`
	lzj	W	lu{
	i
			zzhTzYWWW

TO CHECK THE OUTPUT SPECIFIED FOR AUX 1

You can check the output setting that you speciﬁed in “To specify the alarm operation time for AUX 1”. (See page 31.)

1.Present the Master Card to the device.

2. Press Button 3 and Button 5 in sequence and press ENT .

t

Gj

X Y Z

\ ]

`

lzj W lu{

i

zzhTzYWWW

X Y Z

\ ]

^_ `

lzj W lu{

i

zzhTzYWWW

40_ additional features

Image 40

Contents Standalone Rfid Access Controller Imagine the possibilitiesSafety information Safety informationImportant Safety Instructions This device may not cause harmful interference,Contents To specify the input mode for AUX To specify the input mode for the DoorTo specify the use of the tamper alarm Contact Sensor alarmFeatures Product introductionQuick Guide Rings Diodes UF4004, 1N4001~4007 WHAT’S IncludedMaster Card Cables AT a Glance Front ViewCable Color Scheme Installation and external connection Cable Selection DC12VBypass Diode Connection ConnectionOutput Connection External Reader Connection Basic Operations InitializationIf you press the Exit button, the door will be opened Wiegand Output Setup InitializationBrown line with white stripes TTL Output Chime Bell OutputForced Initialization with External Line Hardware Forcible InitializationReader Mode Setup RF only Reader mode setupNo Master Card or Master PIN is ever registered Reader Mode Setup PIN only Reader Mode Setup RF + P/WPress Button 0 and Button Enabling Keypad Input for the Card Number Reader Mode Setup RF/PIN Combination ModeButton Sequence, and press ENT User management To Register Cards in RF only ModeRegistering Cards in a Combination of RF and P/W Modes Registering Cards in RF Card / PIN Combination Mode To Register Cards in PIN ModeMaster PIN To Delete a Registered Card or PIN Number Duress Alarm Basic setupTo Specify the Retry Count for AN Unregistered ID To Specify the Delayed Start Time in Secure Mode  See the table below for your referenceTo Specify the Operation Time of the Door Contact Sensor To Specify the Limited Time for the Keypad InputTo Specify the Alarm Output Port for the Dismantled Device To Open or Close the Entry DoorTo SET or Release the Quick Mode To SET or Release the Toggle Mode for the Door RelayDefault is set to not used Buttons and press ENTTo Specify the Output Time if the Card is Authenticated Time setupYou can specify from 10 to To Specify the Output Time if the Card is not Authenticated To Specify the Duress TTL OutputTo Specify the Alarm Operation Time for AUX Enter the two-digit TTL relay output time and press ENT32 I/O time setup \ ` Advanced setting To Specify the TTL Output Operation Mode The default is set to switch from HIGH5V to LOW0V  The default is set to use the chime bellTo Specify the Input Mode for AUX To Specify the Chime Bell Operation TimeAdvanced setting To Specify the Input Mode for the Exit Button To Specify the Input Mode for the Door Contact SensorTo Specify the USE of the Tamper Alarm Additional featuresMute To Check the Output Specified for a Registered Card User To Check the Output Specified for AN Unregistered Card UserTo Check the Output Specified for AUX Additional Features Initial Values Other informationThis product operates in the following initial values Function Codes Sense if AUX 1 switches from L to H Sense if AUX 1 switches from H to LSense if AUX 2 switches from L to H Sense if AUX 2 switches from H to LTroubleshooting Troubleshooting√ RF Only √ Enter the command to delete the user 14 + ENT Service centerEInstall and use the product as usual Check the operation status of the productUsing the keypad Unregistered numbers in 5 consecutive times defaultUser cards to the factory default CIf SSA-S2000 responds when you press the Exit buttonIrrelevant data is transferred Disconnection or short-circuitSSA-S2000 Consult with a qualiﬁed technicianProduct Specifications Weight 220gProduct speciﬁcations 87.0 x 109.0 xCorrect disposal of batteries in this product