Samsung SSA-S2000/EXP manual Advanced setting

Page 36

advanced setting

TO SPECIFY THE INPUT MODE FOR AUX 2

You can specify an operation for the auxiliary port 2 when it switches from LOW (0V) to HIGH (5V).

1.Present the Master Card to the device.

2. Press Button 6 and Button 3 in sequence and press ENT .

To release the setting, press the < 6 4 > buttons and press ENT .

tˆš›Œ™Gjˆ™‹

X Y Z

\ ]

`

lzj W lu{

iŒ““

zzhTzYWWW

MThe default is set to “switch from HIGH(5V) to LOW(0V)”.

TO SPECIFY THE INPUT MODE FOR AUX 3

You can specify an operation for the auxiliary port 3 when it switches from LOW (0V) to HIGH (5V).

1.Present the Master Card to the device.

2. Press Button 6 and Button 5 in sequence and press ENT .

To release the setting, repeat Step 1 above, select the

< 6 6 > buttons and press ENT .

X Y Z

[ \ ]

_ `

lzj W lu{

iŒ““

zzhTzYWWW

 

X

Y

Z

 

 

\

]

 

 

 

`

tˆš›Œ™Gjˆ™‹

lzj

W

lu{

 

 

iŒ““

 

 

 

 

 

zzhTzYWWW

MThe default is set to “switch from HIGH(5V) to LOW(0V)”.

X Y Z

[\ ] _ `

lzj W lu{

iŒ““

zzhTzYWWW

36_ advanced setting

Image 36
Contents Standalone Rfid Access Controller Imagine the possibilitiesSafety information Safety informationImportant Safety Instructions This device may not cause harmful interference,Contents To specify the input mode for AUX To specify the input mode for the DoorTo specify the use of the tamper alarm Contact Sensor alarmFeatures Product introductionWHAT’S Included Quick Guide Rings Diodes UF4004, 1N4001~4007Master Card Cables AT a Glance Front ViewCable Color Scheme Installation and external connection Cable Selection DC12VBypass Diode Connection ConnectionOutput Connection External Reader Connection Initialization Basic OperationsIf you press the Exit button, the door will be opened Wiegand Output Setup InitializationBrown line with white stripes TTL Output Chime Bell OutputForced Initialization with External Line Hardware Forcible InitializationReader mode setup Reader Mode Setup RF onlyNo Master Card or Master PIN is ever registered Reader Mode Setup RF + P/W Reader Mode Setup PIN onlyPress Button 0 and Button Reader Mode Setup RF/PIN Combination Mode Enabling Keypad Input for the Card NumberButton Sequence, and press ENT To Register Cards in RF only Mode User managementRegistering Cards in a Combination of RF and P/W Modes To Register Cards in PIN Mode Registering Cards in RF Card / PIN Combination ModeMaster PIN To Delete a Registered Card or PIN Number Basic setup Duress AlarmTo Specify the Retry Count for AN Unregistered ID To Specify the Delayed Start Time in Secure Mode  See the table below for your referenceTo Specify the Operation Time of the Door Contact Sensor To Specify the Limited Time for the Keypad InputTo Specify the Alarm Output Port for the Dismantled Device To Open or Close the Entry DoorTo SET or Release the Quick Mode To SET or Release the Toggle Mode for the Door RelayDefault is set to not used Buttons and press ENTTime setup To Specify the Output Time if the Card is AuthenticatedYou can specify from 10 to To Specify the Output Time if the Card is not Authenticated To Specify the Duress TTL OutputTo Specify the Alarm Operation Time for AUX Enter the two-digit TTL relay output time and press ENT32 I/O time setup \ ` Advanced setting To Specify the TTL Output Operation Mode The default is set to switch from HIGH5V to LOW0V  The default is set to use the chime bellTo Specify the Input Mode for AUX To Specify the Chime Bell Operation TimeAdvanced setting To Specify the Input Mode for the Exit Button To Specify the Input Mode for the Door Contact SensorAdditional features To Specify the USE of the Tamper AlarmMute To Check the Output Specified for a Registered Card User To Check the Output Specified for AN Unregistered Card UserTo Check the Output Specified for AUX Additional Features Other information Initial ValuesThis product operates in the following initial values Function Codes Sense if AUX 1 switches from L to H Sense if AUX 1 switches from H to LSense if AUX 2 switches from L to H Sense if AUX 2 switches from H to LTroubleshooting Troubleshooting√ RF Only √ Enter the command to delete the user 14 + ENT Service centerEInstall and use the product as usual Check the operation status of the productUsing the keypad Unregistered numbers in 5 consecutive times defaultUser cards to the factory default CIf SSA-S2000 responds when you press the Exit buttonIrrelevant data is transferred Disconnection or short-circuitSSA-S2000 Consult with a qualified technicianProduct Specifications Weight 220gProduct specifications 87.0 x 109.0 xCorrect disposal of batteries in this product