Samsung SSA-S2000/EXP manual WHAT’S Included, Quick Guide Rings Diodes UF4004, 1N4001~4007

Page 7

WHAT’S INCLUDED

Check if the following items are included in the product package.

X Y Z

[\ ] ^ _ `

lzj W lu{

i

zzhTzYWWW

Main Unit

3.5x 40mm Screws (x4)

3.5x 12mm Screws (x4)

6 x 30mm Plastic Anchors (x4)

Wall Mount

xGn

Quick Guide

O-rings (x5)

Diodes (x2)

(UF4004, 1N4001~4007)

PRODUCT INTRODUCTION

tGj

Master Card (x1)

Cables (x4)

CD Manual

English _ 7

Image 7

Contents Imagine the possibilities Standalone Rfid Access ControllerSafety information Safety informationThis device may not cause harmful interference, Important Safety Instructions Contents Contact Sensor alarm To specify the input mode for AUXTo specify the input mode for the Door To specify the use of the tamper alarmProduct introduction FeaturesQuick Guide Rings Diodes UF4004, 1N4001~4007 WHAT’S IncludedMaster Card Cables Front View AT a GlanceCable Color Scheme Installation and external connection DC12V Cable SelectionConnection Bypass Diode ConnectionOutput Connection External Reader Connection Basic Operations InitializationIf you press the Exit button, the door will be opened TTL Output Chime Bell Output Wiegand Output SetupInitialization Brown line with white stripesHardware Forcible Initialization Forced Initialization with External LineReader Mode Setup RF only Reader mode setupNo Master Card or Master PIN is ever registered Reader Mode Setup PIN only Reader Mode Setup RF + P/WPress Button 0 and Button Enabling Keypad Input for the Card Number Reader Mode Setup RF/PIN Combination ModeButton Sequence, and press ENT User management To Register Cards in RF only ModeRegistering Cards in a Combination of RF and P/W Modes Registering Cards in RF Card / PIN Combination Mode To Register Cards in PIN ModeMaster PIN To Delete a Registered Card or PIN Number Duress Alarm Basic setupTo Specify the Retry Count for AN Unregistered ID  See the table below for your reference To Specify the Delayed Start Time in Secure ModeTo Specify the Limited Time for the Keypad Input To Specify the Operation Time of the Door Contact SensorTo Open or Close the Entry Door To Specify the Alarm Output Port for the Dismantled DeviceButtons and press ENT To SET or Release the Quick ModeTo SET or Release the Toggle Mode for the Door Relay Default is set to not usedTo Specify the Output Time if the Card is Authenticated Time setupYou can specify from 10 to To Specify the Duress TTL Output To Specify the Output Time if the Card is not AuthenticatedEnter the two-digit TTL relay output time and press ENT To Specify the Alarm Operation Time for AUX32 I/O time setup \ `  The default is set to use the chime bell Advanced settingTo Specify the TTL Output Operation Mode  The default is set to switch from HIGH5V to LOW0VTo Specify the Chime Bell Operation Time To Specify the Input Mode for AUXAdvanced setting To Specify the Input Mode for the Door Contact Sensor To Specify the Input Mode for the Exit ButtonTo Specify the USE of the Tamper Alarm Additional featuresMute To Check the Output Specified for AN Unregistered Card User To Check the Output Specified for a Registered Card UserTo Check the Output Specified for AUX Additional Features Initial Values Other informationThis product operates in the following initial values Function Codes Sense if AUX 2 switches from H to L Sense if AUX 1 switches from L to HSense if AUX 1 switches from H to L Sense if AUX 2 switches from L to HTroubleshooting Troubleshooting√ RF Only Check the operation status of the product √ Enter the command to delete the user 14 + ENTService center EInstall and use the product as usualCIf SSA-S2000 responds when you press the Exit button Using the keypadUnregistered numbers in 5 consecutive times default User cards to the factory defaultConsult with a qualiﬁed technician Irrelevant data is transferredDisconnection or short-circuit SSA-S200087.0 x 109.0 x Product SpecificationsWeight 220g Product speciﬁcationsCorrect disposal of batteries in this product