Samsung SSA-S2000/EXP manual Reader Mode Setup RF + P/W, Reader Mode Setup PIN only

Page 19

READER MODE SETUP (RF + P/W)

No Master Card or Master PIN is ever registered.

If you remember the Master Card or the Master PIN was registered, initialize the product and try again.

1.When you turn on the product, all of the 3 LED indicators will flash with a beep.

No flashing of the 3 indicators denotes that the reader mode is already specified.

2. Press Button 0 and Button 2 in sequence and press ENT .

3.Present a card that you want to register as the Master Card to the device. When the Master Card is registered, only the red LED indicator flashes.

4.Present a card to the device, enter the 4-6 digit password and press ENT .

If you don’t want to register the cards right now, simply jump to Step 5 above without through Step 4 above.

5.Present the registered Master Card to the product once again.

6.The device enters Standby mode with only the orange LED indicator flashing.

X Y Z

[\ ] ^ _ `

lzj W lu{

iŒ““

zzhTzYWWW

READER MODE SETUP

X Y Z

Î

X Y Z

Î

X Y Z

Î

 

X Y Z

[

 

]

[

\

]

[

\

]

tˆš›Œ

\

]

 

 

`

 

^

_

`

 

^

_

`

 

 

 

`

tˆš›Œ™Gjˆ™‹

W

lu{

 

lzj

W

lu{

 

lzj

W

lu{

 

 

lzj W

lu{

lzj

 

 

 

 

 

™Gjˆ™‹

iŒ““

 

 

 

iŒ““

 

 

 

iŒ““

 

 

 

 

iŒ““

 

 

 

zzhTzYWWW

 

 

 

zzhTzYWWW

 

 

 

zzhTzYWWW

 

 

 

zzhTzYWWW

READER MODE SETUP (PIN ONLY)

No Master Card or Master PIN is ever registered.

If you remember the Master Card or the Master PIN was registered, initialize the product and try again.

1.When you turn on the product, all of the 3 LED indicators will flash with a beep.

No flashing of the 3 indicators denotes that the reader mode is already specified.

X Y Z

[\ ] ^ _ `

lzj W lu{

2. Press Button 0 and Button 3

in sequence and press

ENT .

iŒ““

zzhTzYWWW

When the mode is specified, only the green LED indicator flashes.

3.Enter the 4-6 digit Master PIN number and press ENT .

When the Master PIN is registered, only the red LED indicator flashes.

4.Enter a PIN number to register (4-6 digits) and press ENT .

Repeat the step above if you want to register PIN numbers with the device in sequence.

If you don’t want to register the PIN number right now, simply jump to Step 5 above without through Step 4 above.

5.Enter the 4-6 digit Master PIN number again and press ENT .

6.The device enters Standby mode with only the orange LED indicator flashing.

English _ 19

Image 19
Contents Imagine the possibilities Standalone Rfid Access ControllerSafety information Safety informationThis device may not cause harmful interference, Important Safety InstructionsContents Contact Sensor alarm To specify the input mode for AUXTo specify the input mode for the Door To specify the use of the tamper alarmProduct introduction FeaturesQuick Guide Rings Diodes UF4004, 1N4001~4007 WHAT’S IncludedMaster Card Cables Front View AT a GlanceCable Color Scheme Installation and external connection DC12V Cable SelectionConnection Bypass Diode ConnectionOutput Connection External Reader Connection Basic Operations InitializationIf you press the Exit button, the door will be opened TTL Output Chime Bell Output Wiegand Output SetupInitialization Brown line with white stripesHardware Forcible Initialization Forced Initialization with External LineReader Mode Setup RF only Reader mode setupNo Master Card or Master PIN is ever registered Reader Mode Setup PIN only Reader Mode Setup RF + P/WPress Button 0 and Button Enabling Keypad Input for the Card Number Reader Mode Setup RF/PIN Combination ModeButton Sequence, and press ENT User management To Register Cards in RF only ModeRegistering Cards in a Combination of RF and P/W Modes Registering Cards in RF Card / PIN Combination Mode To Register Cards in PIN ModeMaster PIN To Delete a Registered Card or PIN Number Duress Alarm Basic setupTo Specify the Retry Count for AN Unregistered ID  See the table below for your reference To Specify the Delayed Start Time in Secure ModeTo Specify the Limited Time for the Keypad Input To Specify the Operation Time of the Door Contact SensorTo Open or Close the Entry Door To Specify the Alarm Output Port for the Dismantled DeviceButtons and press ENT To SET or Release the Quick ModeTo SET or Release the Toggle Mode for the Door Relay Default is set to not usedTo Specify the Output Time if the Card is Authenticated Time setupYou can specify from 10 to To Specify the Duress TTL Output To Specify the Output Time if the Card is not AuthenticatedEnter the two-digit TTL relay output time and press ENT To Specify the Alarm Operation Time for AUX32 I/O time setup \ `  The default is set to use the chime bell Advanced settingTo Specify the TTL Output Operation Mode  The default is set to switch from HIGH5V to LOW0VTo Specify the Chime Bell Operation Time To Specify the Input Mode for AUXAdvanced setting To Specify the Input Mode for the Door Contact Sensor To Specify the Input Mode for the Exit ButtonTo Specify the USE of the Tamper Alarm Additional featuresMute To Check the Output Specified for AN Unregistered Card User To Check the Output Specified for a Registered Card UserTo Check the Output Specified for AUX Additional Features Initial Values Other informationThis product operates in the following initial values Function Codes Sense if AUX 2 switches from H to L Sense if AUX 1 switches from L to HSense if AUX 1 switches from H to L Sense if AUX 2 switches from L to HTroubleshooting Troubleshooting√ RF Only Check the operation status of the product √ Enter the command to delete the user 14 + ENTService center EInstall and use the product as usualCIf SSA-S2000 responds when you press the Exit button Using the keypadUnregistered numbers in 5 consecutive times default User cards to the factory defaultConsult with a qualified technician Irrelevant data is transferredDisconnection or short-circuit SSA-S200087.0 x 109.0 x Product SpecificationsWeight 220g Product specificationsCorrect disposal of batteries in this product