Samsung SSA-S3010/EXP manual Input Connection

Page 17

I/O CONNECTION

Input Connection

183

"-.

%003

Mon 12 / 12 / 2009

10 : 30 : 20

1 2 3 F1 F2 F3

4 5 6 F4 F5 F6

7 8 9 F7 F8 F9

ESC 0 ENT F10 F11 F12

Door Contact Sensor

Exit Button

Door Contact Sensor: Yellow with the red stripe, GND

Exit Button: Orange line, GND

Connect 2.2K to check for cut-off detection

	GND	FG
Black -	GND
Black -		100V-220V
		L
Red +	DC+12v	N
	DC+12v

Power

Supply

INSTALLATION AND EXTERNAL CONNECTION

1.Connect the DC 12V(+) line of the power supply unit to the red line.

2.Connect the GND(-) line of the power supply unit to the black line.

- Exit Button Connection

1.Connect one end of the Exit button to the orange line.

2.Connect the other end of the Exit button to GND

- Door Contact Sensor Connection

1.Connect one end of the door contact sensor to the yellow with red stripes.

2.Connect the other end of the door contact sensor to GND.

- Auxiliary Input Device Connection (auxiliary input #1 – green, auxiliary input #2 – green with white stripes)

1.Connect one end of the auxiliary input device to auxiliary input #1 or auxiliary input #2.

2.Connect the other end of the auxiliary input device to GND.

English _ 17

Image 17

Contents Please visit our website Standalone Biometric Access ControllerSafety information Safety informationThis device may not cause harmful interference, Important Safety InstructionsSafety Information Contents Contents Wiegand Output Setup Event Memory SetupVoice Volume Setup Input Type SetupProduct introduction FeaturesForced Door Open Alarm External I/O PinsDoor Open Timeout Alarm Duress AlarmQuick Guide CD Manual WHAT’S IncludedLCD AT a GlanceFront Panel Pin Connector Preliminary connector for extension Communication status indicatorRear Panel LEDCable Color Scheme PIN ConnectorPins Signal Cable Color Cable Selection TCP/IP RJ45 ConnectorFollow the instructions below to install the wall mount Installing the Wall MountBypass Diode Connection Connecting the Termination Resistor and DiodeEARTH-GROUNDING the Communication Cables Input Connection ConnectionOutput Connection External Reader Connection External Reader ConnectionRS-232 Communication Port Connection Communication Line ConnectionRS-485 Communication Port Connection Multiple Units RS-485 Communication Port Connection StandaloneMax m Please follow the steps belowConnect all RS-485 ports of the product in parallel TCP/IP Communication Port ConnectionSystem Initialization in Master Mode Initializing the system using the Initialize switchInitialization Initializing the SystemTo register a master card To Access the Master ModeRegistering a Master ID To register a master card PIN To register a master card along with your ﬁngerprint00/00 Lift PUT Your FingerNot USE Name DisplayTo register a master card PIN along with your ﬁngerprint Language Setup User Count SetupCommunication Address Setup DATE/TIME SetupSET DATE/TIME Comm Addr SETFactory Defaults Baud Rate SetupDefault SET Baud RateReader #1 Mode Reader mode setupReader #2 Mode READER#1 Mode ID only JID+F/PP/WRD#1 KEY Input not USE Reader Mode Setup € USE If set, you can get access using the keypad inputReader #1 KEY Input Reader #2 KEY InputDual F/P Mode Jnot USE Dual F/P Mode USE Dual Fingerprint ModeIdentification Mode Adaptive ModeAdaptive Mode not USE Jnot USE Adaptive Mode USE Mode Setup Identification Jnot USEUser management Registering ID in Quick ModeTo register ID To register ID along with ﬁngerprintPW TA TB C RD MA MB LV FP User Management ID Registered Registering the IDTo register the ID card To register the PIN number To register the ID card along with your ﬁngerprintTo select PIN SSA-S30x1 Numeric letters in 4 ~ 8 or 10 digitsTo register the PIN number along with your ﬁngerprint To Delete IDEnter PIN ScreenID List Viewing the ID ListFP REG. Count To Check the Number of Registered FingerprintsALL ID Clear Duress Mode Not USE Duress Password Enter Duress P/W Duress ModeTo delete all registered master IDs Master ID CLRARM/DISARM Door Open Alarm Time SetupOpen ALR Time User Management ARM/DISARM SETTo move to the TWO MEN Mode item TWO MEN Operation ModeTo Check the Number of Events To select USE or not USE, and press ENT . J not USETo Remove the Time Schedule To Remove ALL EventsDoor Contact Sensor Setup Time setupExit Button Output Exit ButtonAuxiliary Input #2 Setup Auxiliary Input #1 SetupTime Setup AUX INPUT#1CUT OFF Output Setup Tamper Alarm Output SetupTamper Alarm CUT OFF AlarmARM/DISARM Output Setup Duress Mode Output SetupRD1 ID OK LV1 Door Open Timeout SetupOutput Setup for Level 4 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 3 IDs Accessing Reader #1 Reader #1 ID Error Output Setup Reader #1 Error Output SetupReader #1 Time Schedule Error Output Setup Reader #1 Antipassback Error Output SetupRD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #2Output Setup for Level 4 IDs Accessing Reader #2 Reader #2 Error Output SetupReader #2 ID Error Output Setup 12.RD2 ID ErrorReader #2 Antipassback Error Output Setup Reader #2 Time Schedule Error Output Setup13.RD2 T/S Error Time Setup 14.RD2 APB ErrorTime Unit Setup Advanced setupOutput Time SCHEDULE+ID Time Unit Unit 1SEC Unit 0.1SECTime Schedule Setup Antipassback ModeAPB Mode Not USE ALL Clear Use the 4 Buttons to specify the interval, dayHoliday Setup Holiday Code Holiday Code SetupCode 01 Code 10Reader #2 Mode Time Schedule Reader Mode Time Schedule Reader #1 Mode Time ScheduleRD1 Mode I T/S RD2 Mode I T/SVoice Message Time Schedule Output Time Schedule SetupVoice I T/S T/S Code ‘00’ means no Time Schedules are to be appliedCUT OFF SET Input Time Schedule SetupInput CUT OFF Check Setup ID Display Additional featuresEvent Memory Setup Voice Volume Setup Wiegand Output SetupVoice Volume Wiegand Output not USE Not USEONE Time Read Not USE Jnot USE Additional Features  The default setting for One Time Read is not USEONE Time Read Version CheckOutput Test Input TestLCD Test Last UpdateKeypad Test Press ANY KEYReader Test RAM TESTING…Memory Test Reader Test SCANNING…Fingerprint Module Version Check Communication TestFailed If the test has succeeded If the test has failedO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Input Type SetupInput Type Menu Structure Other informationF3 button Menu Structure of the F3 buttonMenu Structure of the F4 button F4 buttonOther Information Menu Structure of the F5 buttonF5 button F6 button Menu Structure of the F6 buttonMenu Structure of the F8 button Menu Structure of the F7 buttonF9 button Menu Structure of the F9 buttonMenu Structure of the F10 button F10 buttonOutput Settings for Input Sources Default SettingsDuress Alarm TTL#1 TTL#2Output Setting for Authentication Trouble Shooting TroubleshootingTroubleshooting Communication between Buzzer keeps beepingController and the Host PC fails SoftwareProduct speciﬁcations Product SpecificationsCorrect disposal of batteries in this product