Samsung SSA-S3010/EXP manual Reader #1 Error Output Setup, Reader #1 ID Error Output Setup

Page 50

I/O time setup

READER #1 ERROR OUTPUT SETUP

READER #1 ID Error Output Setup

1.Press the F6 SETUP MENU button.

2. Use the buttons 4 and 6 to move to the RD1 ID ERROR item and press ENT .

3.You can make input when the prompt blinks.

•If you enter ‘00’, no output setting is configured.

•Use the keypad to enter the time for each output operation and press ENT . DR : Door relay output

AR : Alarm relay output

T1 : TTL #1 output

T2 : TTL #2 output

BZ : Buzzer output

5.RD1 ID ERROR

D R	A R	T 1	T 2	B Z
0 0	0 3	0 0	0 0	0 0
5.RD1 ID ERROR
D R	A R	T 1	T 2	B Z
_ 0	0 3	0 0	0 0	0 0

M	 The output time differs, depending on the time unit.
	If the time unit is 0.1 (second), you can specify the value between 0.0 and 9.8 second; if set to 1 (second), you can
	specify between 0 and 98 seconds.
	For the time unit, refer to the ‘Time Unit Setup’ under the advanced setup. (see page 54)
	 If you enter 99 for the value, the product stays in output mode until you change the setting regardless of the time
	unit.

READER #1 Time Schedule Error Output Setup

1.Press the F6 SETUP MENU button.

2. Use the buttons 4 and 6 to move to the RD1 T/S ERROR item and	6.RD1 T/S ERROR
press ENT .

•The operation time for each output is the same as in “READER #1 ID Error Output Setup” above.

M Time schedule must be conﬁgured before. (See Page 55 for “Time Schedule Setup”.)

READER #1 Antipassback Error Output Setup

D R	A R	T 1	T 2	B Z
0 0	0 3	0 0	0 0	0 0

1.Press the F6 SETUP MENU button.

2. Use the buttons 4 and 6 to move to the RD1 APB ERROR item and press ENT .

•The operation time for each output is the same as in “READER #1 ID Error Output Setup” above.

M APB mode must be enabled before. (See Page 55 for “AntiPassBack Mode”.)

7.RD1 APB ERROR

D R	A R	T 1	T 2	B Z
0 0	0 3	0 0	0 0	0 0

50_ I/O time setup

Image 50

Contents Standalone Biometric Access Controller Please visit our websiteSafety information Safety informationThis device may not cause harmful interference, Important Safety InstructionsSafety Information Contents Contents Voice Volume Setup Event Memory SetupWiegand Output Setup Input Type SetupFeatures Product introductionDoor Open Timeout Alarm External I/O PinsForced Door Open Alarm Duress AlarmWHAT’S Included Quick Guide CD ManualLCD AT a GlanceFront Panel Rear Panel Communication status indicatorPin Connector Preliminary connector for extension LEDCable Color Scheme PIN ConnectorPins Signal Cable Color TCP/IP RJ45 Connector Cable SelectionInstalling the Wall Mount Follow the instructions below to install the wall mountConnecting the Termination Resistor and Diode Bypass Diode ConnectionEARTH-GROUNDING the Communication Cables Connection Input ConnectionOutput Connection External Reader Connection External Reader ConnectionCommunication Line Connection RS-232 Communication Port ConnectionMax m RS-485 Communication Port Connection StandaloneRS-485 Communication Port Connection Multiple Units Please follow the steps belowTCP/IP Communication Port Connection Connect all RS-485 ports of the product in parallelInitialization Initializing the system using the Initialize switchSystem Initialization in Master Mode Initializing the SystemTo register a master card To Access the Master ModeRegistering a Master ID 00/00 To register a master card along with your ﬁngerprintTo register a master card PIN Lift PUT Your FingerNot USE Name DisplayTo register a master card PIN along with your ﬁngerprint User Count Setup Language SetupSET DATE/TIME DATE/TIME SetupCommunication Address Setup Comm Addr SETDefault SET Baud Rate SetupFactory Defaults Baud RateReader #2 Mode Reader mode setupReader #1 Mode READER#1 Mode ID only JID+F/PP/WReader #1 KEY Input € USE If set, you can get access using the keypad inputRD#1 KEY Input not USE Reader Mode Setup Reader #2 KEY InputDual Fingerprint Mode Dual F/P Mode Jnot USE Dual F/P Mode USEAdaptive Mode not USE Jnot USE Adaptive Mode USE Mode Setup Adaptive ModeIdentification Mode Identification Jnot USETo register ID Registering ID in Quick ModeUser management To register ID along with ﬁngerprintPW TA TB C RD MA MB LV FP User Management ID Registered Registering the IDTo register the ID card To select PIN To register the ID card along with your ﬁngerprintTo register the PIN number SSA-S30x1 Numeric letters in 4 ~ 8 or 10 digitsEnter PIN To Delete IDTo register the PIN number along with your ﬁngerprint ScreenViewing the ID List ID ListFP REG. Count To Check the Number of Registered FingerprintsALL ID Clear To delete all registered master IDs Duress ModeDuress Mode Not USE Duress Password Enter Duress P/W Master ID CLROpen ALR Time User Management Door Open Alarm Time SetupARM/DISARM ARM/DISARM SETTo Check the Number of Events TWO MEN Operation ModeTo move to the TWO MEN Mode item To select USE or not USE, and press ENT . J not USETo Remove ALL Events To Remove the Time ScheduleExit Button Output Time setupDoor Contact Sensor Setup Exit ButtonTime Setup Auxiliary Input #1 SetupAuxiliary Input #2 Setup AUX INPUT#1Tamper Alarm Tamper Alarm Output SetupCUT OFF Output Setup CUT OFF AlarmDuress Mode Output Setup ARM/DISARM Output SetupDoor Open Timeout Setup RD1 ID OK LV1Output Setup for Level 4 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 3 IDs Accessing Reader #1 Reader #1 Time Schedule Error Output Setup Reader #1 Error Output SetupReader #1 ID Error Output Setup Reader #1 Antipassback Error Output SetupOutput Setup for Level IDS Accessing Reader #2 RD2 ID OK LV2Reader #2 ID Error Output Setup Reader #2 Error Output SetupOutput Setup for Level 4 IDs Accessing Reader #2 12.RD2 ID Error13.RD2 T/S Error Time Setup Reader #2 Time Schedule Error Output SetupReader #2 Antipassback Error Output Setup 14.RD2 APB ErrorOutput Time SCHEDULE+ID Advanced setupTime Unit Setup Time Unit Unit 1SEC Unit 0.1SECAPB Mode Not USE ALL Clear Antipassback ModeTime Schedule Setup Use the 4 Buttons to specify the interval, dayHoliday Setup Code 01 Holiday Code SetupHoliday Code Code 10RD1 Mode I T/S Reader Mode Time Schedule Reader #1 Mode Time ScheduleReader #2 Mode Time Schedule RD2 Mode I T/SVoice I T/S Output Time Schedule SetupVoice Message Time Schedule T/S Code ‘00’ means no Time Schedules are to be appliedCUT OFF SET Input Time Schedule SetupInput CUT OFF Check Setup ID Display Additional featuresEvent Memory Setup Voice Volume Wiegand Output SetupVoice Volume Setup Wiegand Output not USE Not USEONE Time Read  The default setting for One Time Read is not USEONE Time Read Not USE Jnot USE Additional Features Version CheckInput Test Output TestKeypad Test Last UpdateLCD Test Press ANY KEYMemory Test RAM TESTING…Reader Test Reader Test SCANNING…Failed Communication TestFingerprint Module Version Check If the test has succeeded If the test has failedO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Input Type SetupInput Type Other information Menu StructureMenu Structure of the F4 button Menu Structure of the F3 buttonF3 button F4 buttonOther Information Menu Structure of the F5 buttonF5 button Menu Structure of the F6 button F6 buttonMenu Structure of the F7 button Menu Structure of the F8 buttonMenu Structure of the F10 button Menu Structure of the F9 buttonF9 button F10 buttonDuress Alarm Default SettingsOutput Settings for Input Sources TTL#1 TTL#2Output Setting for Authentication Trouble Shooting TroubleshootingTroubleshooting Controller and the Host PC fails Buzzer keeps beepingCommunication between SoftwareProduct Specifications Product speciﬁcationsCorrect disposal of batteries in this product