Samsung SSA-S3010/EXP manual RS-485 Communication Port Connection Standalone, Max m

Page 21

RS-485 Communication Port Connection (Standalone)

A RS-485/RS-232 converter is needed to make RS485 communications between the product and the host PC.

Please follow the steps below:

RS-485/RS-232 Converter

A B

RS-232

RS-485

Max. 1200m

Gray

Yellow

HOST PC

Mon 12 / 12 / 2009

10 : 30 : 20

1 2 3 F1 F2 F3

4 5 6 F4 F5 F6

7 8 9 F7 F8 F9

ESC 0 ENT F10 F11 F12

INSTALLATION AND EXTERNAL CONNECTION

1.Connect the yellow RS-485 RTX (+) line to RS-485 A port of the converter.

2.Connect the gray RS-485 RTX (-) line to RS-485 B port of the converter.

3.Plug in the 9-pin connector (RS-232) of the converter into serial port (COM port) of the host PC.

4.Install and launch the application (SAMS).

RS-485 Communication Port Connection (Multiple Units)

A RS-485/RS-232 converter is needed to make RS-485 communications across a multiple of the products and the host PC.

Please follow the steps below:

RS-485/RS-232 Converter

RS-232

A B	RS-485	HOST PC

Max. 1200m

Gray

Yellow

Mon 12

/ 12 / 2009

Mon 12

/ 12 / 2009

Mon 12

/ 12 / 2009

Mon 12

/ 12 / 2009

10 :

30 : 20

10 :

30 : 20

10 :

30 : 20

10 :

30 : 20

1	2	3	F1	F2	F3	1	2	3	F1	F2	F3	1	2	3	F1	F2	F3	1	2	3	F1	F2	F3
4	5	6	F4	F5	F6	4	5	6	F4	F5	F6	4	5	6	F4	F5	F6	4	5	6	F4	F5	F6
7	8	9	F7	F8	F9	7	8	9	F7	F8	F9	7	8	9	F7	F8	F9	7	8	9	F7	F8	F9
ESC	0	ENT	F10	F11	F12	ESC	0	ENT	F10	F11	F12	ESC	0	ENT	F10	F11	F12	ESC	0	ENT	F10	F11	F12

English _ 21

Image 21

Contents Please visit our website Standalone Biometric Access ControllerSafety information Safety informationImportant Safety Instructions Safety InformationThis device may not cause harmful interference, Contents Contents Wiegand Output Setup Event Memory SetupVoice Volume Setup Input Type SetupProduct introduction FeaturesForced Door Open Alarm External I/O PinsDoor Open Timeout Alarm Duress AlarmQuick Guide CD Manual WHAT’S IncludedAT a Glance Front PanelLCD Pin Connector Preliminary connector for extension Communication status indicatorRear Panel LEDPIN Connector Pins Signal Cable ColorCable Color Scheme Cable Selection TCP/IP RJ45 ConnectorFollow the instructions below to install the wall mount Installing the Wall MountBypass Diode Connection Connecting the Termination Resistor and DiodeEARTH-GROUNDING the Communication Cables Input Connection Connection Output Connection External Reader Connection External Reader ConnectionRS-232 Communication Port Connection Communication Line ConnectionRS-485 Communication Port Connection Multiple Units RS-485 Communication Port Connection StandaloneMax m Please follow the steps belowConnect all RS-485 ports of the product in parallel TCP/IP Communication Port ConnectionSystem Initialization in Master Mode Initializing the system using the Initialize switchInitialization Initializing the SystemTo Access the Master Mode Registering a Master IDTo register a master card To register a master card PIN To register a master card along with your ﬁngerprint00/00 Lift PUT Your FingerName Display To register a master card PIN along with your ﬁngerprintNot USE Language Setup User Count SetupCommunication Address Setup DATE/TIME SetupSET DATE/TIME Comm Addr SETFactory Defaults Baud Rate SetupDefault SET Baud RateReader #1 Mode Reader mode setupReader #2 Mode READER#1 Mode ID only JID+F/PP/WRD#1 KEY Input not USE Reader Mode Setup € USE If set, you can get access using the keypad inputReader #1 KEY Input Reader #2 KEY InputDual F/P Mode Jnot USE Dual F/P Mode USE Dual Fingerprint ModeIdentification Mode Adaptive ModeAdaptive Mode not USE Jnot USE Adaptive Mode USE Mode Setup Identification Jnot USEUser management Registering ID in Quick ModeTo register ID To register ID along with ﬁngerprintRegistering the ID To register the ID cardPW TA TB C RD MA MB LV FP User Management ID Registered To register the PIN number To register the ID card along with your ﬁngerprintTo select PIN SSA-S30x1 Numeric letters in 4 ~ 8 or 10 digitsTo register the PIN number along with your ﬁngerprint To Delete IDEnter PIN ScreenID List Viewing the ID ListTo Check the Number of Registered Fingerprints ALL ID ClearFP REG. Count Duress Mode Not USE Duress Password Enter Duress P/W Duress ModeTo delete all registered master IDs Master ID CLRARM/DISARM Door Open Alarm Time SetupOpen ALR Time User Management ARM/DISARM SETTo move to the TWO MEN Mode item TWO MEN Operation ModeTo Check the Number of Events To select USE or not USE, and press ENT . J not USETo Remove the Time Schedule To Remove ALL EventsDoor Contact Sensor Setup Time setupExit Button Output Exit ButtonAuxiliary Input #2 Setup Auxiliary Input #1 SetupTime Setup AUX INPUT#1CUT OFF Output Setup Tamper Alarm Output SetupTamper Alarm CUT OFF AlarmARM/DISARM Output Setup Duress Mode Output SetupRD1 ID OK LV1 Door Open Timeout SetupOutput Setup for Level 2 IDs Accessing Reader #1 Output Setup for Level 3 IDs Accessing Reader #1Output Setup for Level 4 IDs Accessing Reader #1 Reader #1 ID Error Output Setup Reader #1 Error Output SetupReader #1 Time Schedule Error Output Setup Reader #1 Antipassback Error Output SetupRD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #2Output Setup for Level 4 IDs Accessing Reader #2 Reader #2 Error Output SetupReader #2 ID Error Output Setup 12.RD2 ID ErrorReader #2 Antipassback Error Output Setup Reader #2 Time Schedule Error Output Setup13.RD2 T/S Error Time Setup 14.RD2 APB ErrorTime Unit Setup Advanced setupOutput Time SCHEDULE+ID Time Unit Unit 1SEC Unit 0.1SECTime Schedule Setup Antipassback ModeAPB Mode Not USE ALL Clear Use the 4 Buttons to specify the interval, dayHoliday Setup Holiday Code Holiday Code SetupCode 01 Code 10Reader #2 Mode Time Schedule Reader Mode Time Schedule Reader #1 Mode Time ScheduleRD1 Mode I T/S RD2 Mode I T/SVoice Message Time Schedule Output Time Schedule SetupVoice I T/S T/S Code ‘00’ means no Time Schedules are to be appliedInput Time Schedule Setup Input CUT OFF Check SetupCUT OFF SET Additional features Event Memory SetupID Display Voice Volume Setup Wiegand Output SetupVoice Volume Wiegand Output not USE Not USEONE Time Read Not USE Jnot USE Additional Features  The default setting for One Time Read is not USEONE Time Read Version CheckOutput Test Input TestLCD Test Last UpdateKeypad Test Press ANY KEYReader Test RAM TESTING…Memory Test Reader Test SCANNING…Fingerprint Module Version Check Communication TestFailed If the test has succeeded If the test has failedInput Type Setup Input TypeO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Menu Structure Other informationF3 button Menu Structure of the F3 buttonMenu Structure of the F4 button F4 buttonMenu Structure of the F5 button F5 buttonOther Information F6 button Menu Structure of the F6 buttonMenu Structure of the F8 button Menu Structure of the F7 buttonF9 button Menu Structure of the F9 buttonMenu Structure of the F10 button F10 buttonOutput Settings for Input Sources Default SettingsDuress Alarm TTL#1 TTL#2Output Setting for Authentication Troubleshooting TroubleshootingTrouble Shooting Communication between Buzzer keeps beepingController and the Host PC fails SoftwareProduct speciﬁcations Product SpecificationsCorrect disposal of batteries in this product