Samsung SSA-S3010/EXP manual User Count Setup, Language Setup

Page 27

USER COUNT SETUP

You can select the maximum number of registered users to 10,000 or 20,000.

If you set the maximum user count to 20,000, the maximum number of events will be changed to 10,000.

1.Press the F3 SETUP MENU button.

2.

Use the buttons

4

and

6

to move to the MAX USER SETUP item and

 

press ENT .

 

 

 

 

3.

Use the buttons

4

and

6

to select a max user count.

•10,000 : The max user count will be set to 10,000.

20,000 : The max user count will be set to 20,000.

MBefore setting the user count, you must initialize the system.

LANGUAGE SETUP

5.MAX USER SETUP 10000

5. MAX USER SETUP

J10000

INITIALIZATION

1.Press the F1 SETUP MENU button.

2.

Use the buttons

4

and

6

to move to the LANGUAGE item and press

 

ENT .

 

 

 

 

3.

Use the buttons

4

and

6

to select a max user count.

•€ ENGLISH

€ESPANOL

€PORTUGUESE

€한국어

MThe default language is ENGLISH.

By default, English, Spanish, Portuguese and Korean are supported.

1.LANGUAGE ENGLISH

1. LANGUAGE

JENGLISH

English _ 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Please visit our website Standalone Biometric Access ControllerSafety information Safety informationImportant Safety Instructions Safety InformationThis device may not cause harmful interference, Contents Contents Input Type Setup Event Memory SetupWiegand Output Setup Voice Volume SetupProduct introduction FeaturesDuress Alarm External I/O PinsForced Door Open Alarm Door Open Timeout AlarmQuick Guide CD Manual WHAT’S IncludedAT a Glance Front PanelLCD LED Communication status indicatorPin Connector Preliminary connector for extension Rear PanelPIN Connector Pins Signal Cable ColorCable Color Scheme Cable Selection TCP/IP RJ45 ConnectorFollow the instructions below to install the wall mount Installing the Wall MountBypass Diode Connection Connecting the Termination Resistor and DiodeEARTH-GROUNDING the Communication Cables Input Connection ConnectionOutput Connection External Reader Connection External Reader ConnectionRS-232 Communication Port Connection Communication Line ConnectionPlease follow the steps below RS-485 Communication Port Connection StandaloneRS-485 Communication Port Connection Multiple Units Max mConnect all RS-485 ports of the product in parallel TCP/IP Communication Port ConnectionInitializing the System Initializing the system using the Initialize switchSystem Initialization in Master Mode Initialization To Access the Master Mode Registering a Master ID To register a master card Lift PUT Your Finger To register a master card along with your fingerprintTo register a master card PIN 00/00Name Display To register a master card PIN along with your fingerprintNot USE Language Setup User Count SetupComm Addr SET DATE/TIME SetupCommunication Address Setup SET DATE/TIMEBaud Rate Baud Rate SetupFactory Defaults Default SETREADER#1 Mode ID only JID+F/PP/W Reader mode setupReader #1 Mode Reader #2 ModeReader #2 KEY Input € USE If set, you can get access using the keypad inputRD#1 KEY Input not USE Reader Mode Setup Reader #1 KEY InputDual F/P Mode Jnot USE Dual F/P Mode USE Dual Fingerprint ModeIdentification Jnot USE Adaptive ModeIdentification Mode Adaptive Mode not USE Jnot USE Adaptive Mode USE Mode SetupTo register ID along with fingerprint Registering ID in Quick ModeUser management To register IDRegistering the ID To register the ID cardPW TA TB C RD MA MB LV FP User Management ID Registered SSA-S30x1 Numeric letters in 4 ~ 8 or 10 digits To register the ID card along with your fingerprintTo register the PIN number To select PINScreen To Delete IDTo register the PIN number along with your fingerprint Enter PINID List Viewing the ID ListTo Check the Number of Registered Fingerprints ALL ID ClearFP REG. Count Master ID CLR Duress ModeDuress Mode Not USE Duress Password Enter Duress P/W To delete all registered master IDsARM/DISARM SET Door Open Alarm Time SetupARM/DISARM Open ALR Time User ManagementTo select USE or not USE, and press ENT . J not USE TWO MEN Operation ModeTo move to the TWO MEN Mode item To Check the Number of EventsTo Remove the Time Schedule To Remove ALL EventsExit Button Time setupDoor Contact Sensor Setup Exit Button OutputAUX INPUT#1 Auxiliary Input #1 SetupAuxiliary Input #2 Setup Time SetupCUT OFF Alarm Tamper Alarm Output SetupCUT OFF Output Setup Tamper AlarmARM/DISARM Output Setup Duress Mode Output SetupRD1 ID OK LV1 Door Open Timeout SetupOutput Setup for Level 2 IDs Accessing Reader #1 Output Setup for Level 3 IDs Accessing Reader #1Output Setup for Level 4 IDs Accessing Reader #1 Reader #1 Antipassback Error Output Setup Reader #1 Error Output SetupReader #1 ID Error Output Setup Reader #1 Time Schedule Error Output SetupRD2 ID OK LV2 Output Setup for Level IDS Accessing Reader #212.RD2 ID Error Reader #2 Error Output SetupOutput Setup for Level 4 IDs Accessing Reader #2 Reader #2 ID Error Output Setup14.RD2 APB Error Reader #2 Time Schedule Error Output SetupReader #2 Antipassback Error Output Setup 13.RD2 T/S Error Time SetupTime Unit Unit 1SEC Unit 0.1SEC Advanced setupTime Unit Setup Output Time SCHEDULE+IDUse the 4 Buttons to specify the interval, day Antipassback ModeTime Schedule Setup APB Mode Not USE ALL ClearHoliday Setup Code 10 Holiday Code SetupHoliday Code Code 01RD2 Mode I T/S Reader Mode Time Schedule Reader #1 Mode Time ScheduleReader #2 Mode Time Schedule RD1 Mode I T/ST/S Code ‘00’ means no Time Schedules are to be applied Output Time Schedule SetupVoice Message Time Schedule Voice I T/SInput Time Schedule Setup Input CUT OFF Check SetupCUT OFF SET Additional features Event Memory SetupID Display Wiegand Output not USE Not USE Wiegand Output SetupVoice Volume Setup Voice VolumeVersion Check  The default setting for One Time Read is not USEONE Time Read Not USE Jnot USE Additional Features ONE Time ReadOutput Test Input TestPress ANY KEY Last UpdateLCD Test Keypad TestReader Test SCANNING… RAM TESTING…Reader Test Memory TestIf the test has succeeded If the test has failed Communication TestFingerprint Module Version Check FailedInput Type Setup Input TypeO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Menu Structure Other informationF4 button Menu Structure of the F3 buttonF3 button Menu Structure of the F4 buttonMenu Structure of the F5 button F5 buttonOther Information F6 button Menu Structure of the F6 buttonMenu Structure of the F8 button Menu Structure of the F7 buttonF10 button Menu Structure of the F9 buttonF9 button Menu Structure of the F10 buttonTTL#1 TTL#2 Default SettingsOutput Settings for Input Sources Duress AlarmOutput Setting for Authentication Troubleshooting TroubleshootingTrouble Shooting Software Buzzer keeps beepingCommunication between Controller and the Host PC failsProduct specifications Product SpecificationsCorrect disposal of batteries in this product
Top Page Image Contents