Samsung SSA-S3010/EXP manual Dual Fingerprint Mode, Dual F/P Mode Jnot USE Dual F/P Mode USE

Page 32

reader mode setup

DUAL FINGERPRINT MODE

In Dual Fingerprint mode, you can register two ﬁngerprints for one user ID.

If one of your ﬁngers is damaged with Dual Fingerprint mode set to USE, you can use the other ﬁnger registered for the authentication.

1.Press the F10 SETUP MENU button.

2.	Use the buttons	4	and	6	to move to the DUAL F/P MODE item and
	press ENT .
3.	Use the buttons	4	and	6	to select the use of Dual Fingerprint mode.

• USE : If set, you can use the Dual Fingerprint mode.

NOT USE : If set, Dual Fingerprint mode is disabled.

4. When done, press ENT to save your settings.

M For registering ﬁngerprints, see the following table.

1.DUAL F/P MODE NOT USE

1. DUAL F/P MODE

JNOT USE

1.DUAL F/P MODE USE

	DUAL FINGER	Template/Fingerprint Count	Success	Recommended
	DUAL FINGER	Template/Fingerprint Count	Ratio	Authentication Mode
			Ratio	Authentication Mode
	NOT USE	2 ﬁngerprint templates for one ﬁnger	High	Identiﬁcation mode

USE

1 ﬁngerprint template for each of 2 different ﬁngers

Low

Veriﬁcation mode

J





Make sure not to mix Dual Finger enable/disable conﬁgurations for multiple units. Otherwise, it may degrade the recognition performance or cause data communication errors.

If you switch the Dual Finger setup from disabled to enabled, all systems should have the consistent setups and registered ﬁngerprints must be registered again. Switching to disabled requires the same.

Before registering ﬁngerprints and transfer data, make sure to setup all systems to have consistent setting at the beginning.

32_ reader mode setup

Image 32

Contents Standalone Biometric Access Controller Please visit our websiteSafety information Safety informationThis device may not cause harmful interference, Important Safety InstructionsSafety Information Contents Contents Event Memory Setup Wiegand Output SetupVoice Volume Setup Input Type SetupFeatures Product introductionExternal I/O Pins Forced Door Open AlarmDoor Open Timeout Alarm Duress AlarmWHAT’S Included Quick Guide CD ManualLCD AT a GlanceFront Panel Communication status indicator Pin Connector Preliminary connector for extensionRear Panel LEDCable Color Scheme PIN ConnectorPins Signal Cable Color TCP/IP RJ45 Connector Cable SelectionInstalling the Wall Mount Follow the instructions below to install the wall mountConnecting the Termination Resistor and Diode Bypass Diode ConnectionEARTH-GROUNDING the Communication Cables Connection Input ConnectionOutput Connection External Reader Connection External Reader ConnectionCommunication Line Connection RS-232 Communication Port ConnectionRS-485 Communication Port Connection Standalone RS-485 Communication Port Connection Multiple UnitsMax m Please follow the steps belowTCP/IP Communication Port Connection Connect all RS-485 ports of the product in parallelInitializing the system using the Initialize switch System Initialization in Master ModeInitialization Initializing the SystemTo register a master card To Access the Master ModeRegistering a Master ID To register a master card along with your ﬁngerprint To register a master card PIN00/00 Lift PUT Your FingerNot USE Name DisplayTo register a master card PIN along with your ﬁngerprint User Count Setup Language SetupDATE/TIME Setup Communication Address SetupSET DATE/TIME Comm Addr SETBaud Rate Setup Factory DefaultsDefault SET Baud RateReader mode setup Reader #1 ModeReader #2 Mode READER#1 Mode ID only JID+F/PP/W€ USE If set, you can get access using the keypad input RD#1 KEY Input not USE Reader Mode SetupReader #1 KEY Input Reader #2 KEY InputDual Fingerprint Mode Dual F/P Mode Jnot USE Dual F/P Mode USEAdaptive Mode Identification ModeAdaptive Mode not USE Jnot USE Adaptive Mode USE Mode Setup Identification Jnot USERegistering ID in Quick Mode User managementTo register ID To register ID along with ﬁngerprintPW TA TB C RD MA MB LV FP User Management ID Registered Registering the IDTo register the ID card To register the ID card along with your ﬁngerprint To register the PIN numberTo select PIN SSA-S30x1 Numeric letters in 4 ~ 8 or 10 digitsTo Delete ID To register the PIN number along with your ﬁngerprintEnter PIN ScreenViewing the ID List ID ListFP REG. Count To Check the Number of Registered FingerprintsALL ID Clear Duress Mode Duress Mode Not USE Duress Password Enter Duress P/WTo delete all registered master IDs Master ID CLRDoor Open Alarm Time Setup ARM/DISARMOpen ALR Time User Management ARM/DISARM SETTWO MEN Operation Mode To move to the TWO MEN Mode itemTo Check the Number of Events To select USE or not USE, and press ENT . J not USETo Remove ALL Events To Remove the Time ScheduleTime setup Door Contact Sensor SetupExit Button Output Exit ButtonAuxiliary Input #1 Setup Auxiliary Input #2 SetupTime Setup AUX INPUT#1Tamper Alarm Output Setup CUT OFF Output SetupTamper Alarm CUT OFF AlarmDuress Mode Output Setup ARM/DISARM Output SetupDoor Open Timeout Setup RD1 ID OK LV1Output Setup for Level 4 IDs Accessing Reader #1 Output Setup for Level 2 IDs Accessing Reader #1Output Setup for Level 3 IDs Accessing Reader #1 Reader #1 Error Output Setup Reader #1 ID Error Output SetupReader #1 Time Schedule Error Output Setup Reader #1 Antipassback Error Output SetupOutput Setup for Level IDS Accessing Reader #2 RD2 ID OK LV2Reader #2 Error Output Setup Output Setup for Level 4 IDs Accessing Reader #2Reader #2 ID Error Output Setup 12.RD2 ID ErrorReader #2 Time Schedule Error Output Setup Reader #2 Antipassback Error Output Setup13.RD2 T/S Error Time Setup 14.RD2 APB ErrorAdvanced setup Time Unit SetupOutput Time SCHEDULE+ID Time Unit Unit 1SEC Unit 0.1SECAntipassback Mode Time Schedule SetupAPB Mode Not USE ALL Clear Use the 4 Buttons to specify the interval, dayHoliday Setup Holiday Code Setup Holiday CodeCode 01 Code 10Reader Mode Time Schedule Reader #1 Mode Time Schedule Reader #2 Mode Time ScheduleRD1 Mode I T/S RD2 Mode I T/SOutput Time Schedule Setup Voice Message Time ScheduleVoice I T/S T/S Code ‘00’ means no Time Schedules are to be appliedCUT OFF SET Input Time Schedule SetupInput CUT OFF Check Setup ID Display Additional featuresEvent Memory Setup Wiegand Output Setup Voice Volume SetupVoice Volume Wiegand Output not USE Not USE The default setting for One Time Read is not USE ONE Time Read Not USE Jnot USE Additional FeaturesONE Time Read Version CheckInput Test Output TestLast Update LCD TestKeypad Test Press ANY KEYRAM TESTING… Reader TestMemory Test Reader Test SCANNING…Communication Test Fingerprint Module Version CheckFailed If the test has succeeded If the test has failedO , 0 1 N C E X D C I 1 I 2 T P 0 0 0 0 0 0 0 0 0 Input Type SetupInput Type Other information Menu StructureMenu Structure of the F3 button F3 buttonMenu Structure of the F4 button F4 buttonOther Information Menu Structure of the F5 buttonF5 button Menu Structure of the F6 button F6 buttonMenu Structure of the F7 button Menu Structure of the F8 buttonMenu Structure of the F9 button F9 buttonMenu Structure of the F10 button F10 buttonDefault Settings Output Settings for Input SourcesDuress Alarm TTL#1 TTL#2Output Setting for Authentication Trouble Shooting TroubleshootingTroubleshooting Buzzer keeps beeping Communication betweenController and the Host PC fails SoftwareProduct Specifications Product speciﬁcationsCorrect disposal of batteries in this product