Dansons Group HCF120, HCS, HCF300, HCJ manual Outside AIR, Through The Wall Kits Include

Page 12

OUTSIDE AIR

Outside air is REQUIRED ON ALL MOBILE HOME INSTALLATIONS.

Outside air is strongly recommended for all other installations. Failure to install intake air may result in improper combustion as well as the unit smoking during power failures.

Metal pipe, ONLY, either solid or flexible, must be used in all outside air installations.(B) NOTE: Non-metallic material MUST NOT BE USED for outside air installations.

A wind shield, (C), over the termination of the outside air pipe or a 90 degree elbow or bend directed away from the prevailing winds MUST be used when an outside air pipe is installed through the side of a building. Keep the outside air pipe termination at least 1 foot away from the exhaust system termination.

When outside air is taken from an existing chimney the exhaust system must not terminate in the same chimney.

The outside air pipe on your stove is 2" OD. The outside air connecting pipe must be at least 2" ID The outside air connecting pipe must be as short and free of elbows as possible, and must fit over, (A), not inside, the outside air pipe on your stove.

Through The Wall Kits Include:

3 FOOT PACKAGE PART# ACFAKT03

10 FOOT PACKAGE – PART# ACFAKT10

1

– 2” Galvanized Hood c/w screen

1

– 2” Galvanized Hood c/w screen

1

– 2” Aluminum Flex Duct –

1

– 2” Aluminum Flex Duct –

 

compressed 15” length, extends to 30” – 36”

 

compressed 4’ length, extends to 120”

2

– 2” Worm Gear Clamps

2

– 2” Worm Gear Clamps

NOTE: Available from your local Authorized Dealer or Dansons Group Inc. 1-877-303-3134

Figure 11

Copyright 2004

12

Cheap Charlie Owner’s Manual

Canadian Comfort Industries

www.dansons.com

Dansons Group Inc.

Image 12
Contents Cheap Charlie Dear Cheap Charlie Owner Canadian Comfort Industries Dansons Group IncTable of Contents Safety Precautions Safety Precautions Specifications Automatic Safety Features L250 High Limit SwitchL120 LOW Limit Switch F140 FAN Limit SwitchInstallation Options Read this Entire Manual Before YOU Install and USE YourInstallation Options Include Cheap Charlie Home & Shop HeaterInstallation Check List Vent Installation Exhaust Systems GeneralPellet Vent Type Venting DistancePellet Vent Termination Figures 7 Vent Termination ClearancesOutside AIR Through The Wall Kits IncludeFreestanding Installation Heater PlacementFloor Protection Requirements Minimum Clearances to CombustiblesClearances Corner Installation Alcove InstallationThrough the Wall Direct INSTALLATION. Figure Vertical Installations Figures 19 COMMON, but not inclusive, Vertical Installation Designs areMobile Home Installation Operating Your Stove HOW Your Cheap Charlie Heater WorksLighting stove manually No Igniter NON-Thermostat Mode Lighting Your StoveBasic Overview HOW the Board WorksTrim Pots Fine Tune Adjustments- Factory Settings Shutting the Stove OFFAuger Cycle FAN Speed Convection or heatingDamper Adjustment Guideline Performance Enhancement TipsExcessive Combustion Air Initial Appliance Burn Setup StartFine Tuning the Pellet Feed Rates Pellet FuelPellet Quality Pellet ConsumptionFines PFI Pellet StandardsRequired Routine Cleaning Every 2 -3 Days / WeeklyPeriodic Maintenance Check and Clean the HopperPeriodic Maintenance … Trouble Shooting Problem SolutionLimited Warranty Extended WarrantyINSERTING, Removing & Adjusting the Burn Grate Appendix aBurn box Upper Grate LipAppendix a Burn Grate … Damper Adjustment Guideline Lack of Combustion Air Appendix BOptional Accessories Appendix CReplacement Parts Appendix DSee Your Cheap Charlie Dealer for Additional Info Appendix E OperationHigh / LOW Cycle Option Flashing 3 On / OFF Option Flashing 1Installation Steps Tools NeededHow to Install PurposeTools Needed Service & Maintenance Log