CLEANING |
| WARNING | |
AND | WARNING ICONG 001 | ||
Turn off heater and let cool before cleaning. | |||
MAINTENANCE |
|
|
|
|
| ||
|
| WARNING ICONG 001 | CAUTION |
You must keep control areas, burners, and circulating air passage- ways of heater clean. Inspect these areas of heater before each use. Have heater inspected yearly by a qualified service person. Heater may need more frequent cleaning due to excessive lint from carpeting, bedding material, etc.
ODS/PILOT AND BURNERS
• Use a vacuum cleaner or small, soft bristled brush to clean.
LOGS
•If you remove logs for cleaning, refer to Installing Logs, page 19, to properly replace logs.
•Replace log(s) if broken or chipped
TROUBLE- |
|
|
| WARNING ICONG 001 WARNING |
|
|
|
|
|
SHOOTING |
|
|
|
|
|
|
|
| |
| Turn off and unplug heater and let cool before servicing. Only a |
| |||||||
|
| qualified service person should service and repair heater. |
| ||||||
Note: All troubleshooting |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
items are listed in order of |
|
|
|
|
|
|
|
|
|
|
|
| WARNING ICONG 001 CAUTION |
|
|
|
|
| |
operation. |
|
|
|
|
|
|
|
| |
|
| Never use a wire, needle, or similar object to clean ODS/pilot. This |
| ||||||
|
| can damage ODS/pilot unit. |
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| |
| OBSERVED | POSSIBLE |
|
|
|
|
| ||
| PROBLEM | CAUSE | REMEDY | ||||||
|
|
|
|
|
|
| |||
| When ignitor button | 1. | Ignitor electrode not con- | 1. | Reconnect ignitor cable | ||||
| is pressed, there is no |
| nected to ignitor cable |
|
|
|
|
| |
| spark at ODS/pilot | 2. | Ignitor cable pinched or | 2. | Free ignitor cable if | ||||
|
|
|
| wet |
| pinched by any metal or | |||
|
|
|
|
|
| tubing. Keep ignitor | |||
|
|
|
|
|
| cable dry | |||
|
|
| 3. | Piezo ignitor nut is loose | 3. | Tighten nut holding | |||
|
|
|
|
|
| piezo ignitor to base | |||
|
|
|
|
|
| panel of log set. Nut is | |||
|
|
|
|
|
| located behind base | |||
|
|
|
|
|
| panel. | |||
|
|
| 4. | Broken ignitor cable | 4. | Replace ignitor cable | |||
|
|
| 5. | Bad piezo ignitor | 5. | Replace piezo ignitor | |||
|
|
| 6. | Ignitor electrode posi- | 6. | Replace ignitor | |||
|
|
|
| tioned wrong |
|
|
|
|
|
|
|
| 7. | Ignitor electrode broken | 7. | Replace ignitor | |||
|
|
|
|
|
| Continued |
|
|
|
|
|
|
|
|
| 25 | |||
101308 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |