Desa SF20NT Connecting to GAS Supply, External Regulator With Vent Pointing Down

Page 10

INSTALLATION

Continued

CONNECTING TO GAS SUPPLY

WARNING: This appliance requires a 3/8" NPT (National Pipe Thread) inlet connection to the pressure regulator.

WARNING: A qualified ser- vice person must connect heater to gas supply. Follow all local codes.

WARNING: For natural gas, never connect heater to private (non-utility) gas wells. This gas is commonly known as wellhead gas.

IMPORTANT: For natural gas, check gas line pressure before connecting heater to gas line. Gas line pressure must be no greater than 10.5" of wa- ter. If gas line pressure is higher, heater regulator damage could occur.

CAUTION: For propane/LP gas, never connect heater di- rectly to the propane/LP supply. This heater requires an external regulator (not supplied). Install theexternalregulatorbetweenthe heater and propane/LP supply.

Propane/LP

External

Supply Tank

 

Regulator

Vent

Pointing

Down

Figure 10 - External Regulator With Vent

Pointing Down

For propane/LP gas, the installer must supply an external regulator. The external regulator will reduce incoming gas pressure. You must reduce incoming gas pressure to between 11" and 14" of water. If you do not reduce incoming gas pressure, heater regulator damage could occur. Install the external regulator with the vent pointing down as shown in Figure 10. Pointing the vent down protects it from freezing rain or sleet.

CAUTION: Use only new, black iron or steel pipe. Inter- nally-tinned copper tubing may be used in certain areas. Check your local codes. Use pipe of large enough diameter to allow proper gas volume to heater. If pipe is too small, undue loss of volume will occur.

Typical Inlet Pipe Diameters

20,000 Btu/Hr Models - 3/8" or greater

30,000 Btu/Hr Models - 1/2" or greater

Installation must include equipment shutoff valve, union and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 11, page 11).

IMPORTANT: Install an equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the appliance.

Apply pipe joint sealant lightly to male NPT threads. This will prevent excess sealant from going into pipe. Sealant in pipe could result in clogged heater valves. Most flex gas tubing does not require sealant. Read instructions supplied with flex gas tubing.

WARNING: Use pipe joint sealant that is resistant to liquid petroleum (LP) gas.

Install sediment trap in supply line as shown in Figure 11, page 11. Locate sediment trap where it is within reach for cleaning. Locate sediment trap where trapped matter is not likely to freeze. A sediment trap traps moisture and contaminants. This keeps them from going into heater controls. If sediment trap is not installed or is installed wrong, heater may not run properly.

Install male connector and flex gas line to equipment shutoff valve as shown in Figure 11, page 11.

10

www.desatech.com

116307-01A

Image 10
Contents What to do if YOU Smell GAS Residential Models Garage ModelsTable of Contents Safety Information Local Codes Product FeaturesUnpacking Providing Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation AIR Ventilation Air From Inside BuildingCheck GAS Type InstallationInstallation Items Ventilation Air From OutdoorsColdest part of room Installing Heater to WallLocating Heater Attaching to wall stud Attaching to wall anchorLocate hardware packet behind left side door of heater Marking Screw LocationsMark two screw locations on wall as shown in Figure Attaching To Wall Anchor MethodConnecting to GAS Supply External Regulator With Vent Pointing DownTest Pressures In Excess Of 1/2 Psig 3.5 kPa Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Operating Heater For Your Safety Read Before LightingInstalling Refractory and Front Panel Make sure control knob of heater is in the OFF positionLighting Instructions What to do if YOU Smell GASInspecting Heater Burner Pilot AIR Inlet Cleaning MaintenanceODS/PILOT and Burner CabinetObserved Problem Possible Cause Remedy TroubleshootingContact local propane/LP gas company Assembly Goes out when control knob is Control knob not pressedProblem could be caused by Delayed ignition of burners Manifold pressure is too lowWhen heated, vapors from Turn heater off when using Noise when burner is litDirty or partially clogged Clean burner see Cleaning Turn off air supplyWhen Gas Pressure Is Too Low Technical ServiceService Publications Service Hints Gas leak. See WarningSF30NT SF30PT SpecificationsLSF30NT, VSF30NT LSF30PT, VSF30PT Replacement Parts AccessoriesParts Central Illustrated Parts Breakdown Parts List LSF20PTWarranty Information Keep this WarrantyQUÉ Hacer SI Percibe Olor a GAS Modelos Modelos Para CocheraTabla DE Contenido Información DE Seguridad Desempaque Códigos LocalesIdentificación DEL Producto Características DEL ProductoConstrucción inusualmente sellada Aire Para Combustión VentilaciónCómo Procurar LA Ventilación Adecuada Espacio confinado y no confinadoAire Para Ventilación Aire del interior de la construcción para ventilaciónArtículos DE Instalación InstalaciónVerifique EL Tipo DE GAS Aire del exterior para ventilaciónEn áreas con mucho viento o Ubicación DEL CalentadorColocación del calentador en los tornillos de montaje Instalación DEL Calentador EN LA ParedDoble en anclaje de pared como se muestra en la figura Coloque el calentador en los tornillos de montajeConexión AL Suministro DE GAS Ventila apuntando hacia abajoPropano o gas LP Revisión DE LAS Conexiones DE GASGas natural Repare todas las fugas inmediatamenteInstale el panel anterior y el refractario Abra la válvula de cierre del equipo consulte la figuraInstalación del panel anterior y el refractario Instrucciones DE Encendido No intente encender ningún aparatoFuncionamiento DEL Inspección DEL CalentadorEntrada DE Aire AL Piloto DEL Quemador Inspección DELLimpieza Y Mantenimiento Como se muestra en la figuraSolución DE Problemas Causa Posible RemedioEl termopar está dañado Problema Observado Causa Posible RemedioBaja presión del gas Presione totalmente la perilla de controlSe enciende o se apaga El problema desapareceráCierre el suministro de aire Silbante cuando el quemadorConsejos Para Servicio Servicio TécnicoCuando la presión del gas de entrada sea muy baja SF30NT EspecificacionesLSF30NT, VSF30NT Piezas DE Repuesto AccesoriosCentral DE Piezas Clasificación Ilustrada DE Piezas Lista DE Piezas Información DE Garantía Guarde Esta Garantía

SF20NT specifications

Desa SF20NT is a versatile and innovative gas-fired space heater designed for efficient heating solutions in various environments, whether in residential, commercial, or industrial settings. This model is known for its high performance, energy efficiency, and advanced technology, making it a popular choice among users seeking reliability and effectiveness in their heating needs.

One of the primary features of the Desa SF20NT is its impressive heating capacity. With a heating output of around 20,000 BTUs, it can effectively warm spaces up to 1,000 square feet, making it suitable for larger areas. This capability is enhanced by the heater's superior metal construction, ensuring durability and long-lasting performance.

In terms of technology, the Desa SF20NT incorporates a direct vent system that utilizes outside air for combustion. This feature not only increases efficiency but also enhances safety, as it minimizes the risk of hazardous fumes entering the living space. The direct vent system allows for installation flexibility; the unit can be vented horizontally through a wall or vertically through a roof, catering to different building designs.

Another standout characteristic of the Desa SF20NT is its thermostat control, which allows users to maintain a consistent temperature easily. This feature contributes to energy savings by enabling the heater to operate only when necessary, thus reducing unnecessary heating costs. Additionally, the unit includes a programmable timer, allowing users to set specific heating schedules, further optimizing energy use.

Safety is also a critical aspect of the Desa SF20NT design. It comes with built-in safety features such as a flame sensor and a safety shut-off system, ensuring that the heater operates under safe conditions at all times. The unit is designed to meet stringent safety standards, giving users peace of mind.

In summary, the Desa SF20NT is a powerful, efficient, and safe space heater that is equipped with modern features and technologies. With its high heating capacity, direct vent system, thermostat control, and safety mechanisms, it stands out as an excellent choice for anyone looking for reliable heating solutions. Whether for home or business use, the Desa SF20NT is built to provide comfort and efficiency year-round.