Desa SF20NT Códigos Locales, Identificación DEL Producto, Desempaque, Control DE Calor CON

Page 28

INFORMACIÓN DE SEGURIDAD

Continuación

5.Este calentador necesita ventilación con aire fresco del exterior para funcionar correctamente. Este calentador tiene un sistema de apagado de seguridad con detección de agotamiento de oxí- geno (ODS). La ODS apaga el calentador cuando no hay suficiente aire fresco en la habitación. Consulte Aire para combustión y ventilación, en la página 5.

6.Mantenga limpias y libres de residuos todas las aberturas de las partes anterior e inferior del calentador. Esto asegurará que haya suficiente aire para lograr una combustión adecuada.

7.Si el calentador se apaga, no lo vuelva encender hasta que éste cuente con aire fresco del exterior. Si el calentador se sigue apagando, haga que lo reparen.

8.No haga funcionar el calentador

donde se utilicen o almacenen líquidos o vapores inflamables

en condiciones con mucho polvo

9.No use el calentador si alguna de sus partes ha estado sumergida en agua. Llame inmediatamen- te a un técnico capacitado de servicio para que inspeccione el calentador y para que reemplace las piezas del sistema de control o los controles de gas que hayan estado sumergidos en agua.

10.Apague y desconecte (si utiliza electricidad) el calentador y deje que se enfríe antes de darle servicio. Sólo una persona de servicio capacitada debe repararlo y darle servicio.

11.Hacer funcionar el calentador alturas superiores de 1,371 metros (4,500 pies) puede ocasionar que el piloto se apague.

12.Para evitar problemas de rendimiento, no use tanques de propano o gas LP de menos de 45 kg (100 lb) de capacidad.

13.Apague el calentador antes de usar pulidores de muebles, ceras, limpiadores de alfombras o pro- ductos parecidos. Si se calientan, los vapores que se desprenden de estos productos pueden producir un polvo blanco dentro de la caja del calentador o en las paredes o los muebles adyacentes.

14.Procure que se cumplan las distancias mínimas alrededor de las aberturas de aire.

CÓDIGOS LOCALES

Instale y use el calentador cuidadosamente. Siga todos los códigos locales. Si no tiene los códigos lo- cales, consulte la última edición del Código nacional de gas combustible, ANSI Z223.1/NFPA 54*.

*Disponible en:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018, EE.UU.

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269, EE.UU.

IDENTIFICACIÓN DEL PRODUCTO

 

Perilla de control

Rejilla de

y botón del

encendedor (adentro

resguardo

de la puerta)

 

Panel anterior

Figura 1 - Calentador de gas sin ventilación

DESEMPAQUE

1.Extraiga el calentador, el panel anterior y la parrilla de la caja. Colóquelos a un lado en un lugar seguro.

2.Separe el refractario cuidadosamente del calen- tador y quite el material de empaque. Revise el refractario para ver si sufrió algún daño. Si el refractario está dañado, no lo use. Consulte Piezas de repuesto, en la página 21. Colóquelos a un lado en un lugar seguro.

3.Revise el calentador para ver si sufrió algún daño. Si el calentador está dañado, devuélvalo de inmediato al distribuidor a quien se lo compró.

CARACTERÍSTICAS DEL PRODUCTO

DISPOSITIVO DE SEGURIDAD Este calentador tiene un piloto con un sistema de apa- gado de seguridad con detección de agotamiento de oxígeno (ODS). El piloto con ODS es una caracterís- tica necesaria de los calentadores sin ventilación para habitaciones. El piloto con ODS apaga el calentador cuando no hay suficiente aire fresco.

SISTEMA DE ENCENDIDO Este calentador tiene un encendedor, que puede ser piezoeléctrico o electrónico, para encender el sumi- nistro de combustible del mismo.

CONTROL DE CALOR CON

TERMOSTATO Los modelos con termostato cuentan con un bulbo sensor del termostato y una válvula de control. Esto ofrece gran comodidad al usar el calentador. También puede generar ahorros en el consumo de gas.

4

www.desatech.com

116307-01A

Image 28
Contents What to do if YOU Smell GAS Residential Models Garage ModelsTable of Contents Safety Information Local Codes Product FeaturesUnpacking Providing Adequate Ventilation AIR for Combustion VentilationDetermining FRESH-AIR Flow for Heater Location Ventilation AIR Ventilation Air From Inside BuildingInstallation Installation ItemsCheck GAS Type Ventilation Air From OutdoorsInstalling Heater to Wall Locating HeaterColdest part of room Attaching to wall stud Attaching to wall anchorMarking Screw Locations Mark two screw locations on wall as shown in FigureLocate hardware packet behind left side door of heater Attaching To Wall Anchor MethodConnecting to GAS Supply External Regulator With Vent Pointing DownTest Pressures In Excess Of 1/2 Psig 3.5 kPa Checking GAS ConnectionsTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa For Your Safety Read Before Lighting Installing Refractory and Front PanelOperating Heater Make sure control knob of heater is in the OFF positionLighting Instructions What to do if YOU Smell GASInspecting Heater Cleaning Maintenance ODS/PILOT and BurnerBurner Pilot AIR Inlet CabinetObserved Problem Possible Cause Remedy TroubleshootingContact local propane/LP gas company Goes out when control knob is Control knob not pressed Problem could be caused byAssembly Delayed ignition of burners Manifold pressure is too lowNoise when burner is lit Dirty or partially clogged Clean burner see CleaningWhen heated, vapors from Turn heater off when using Turn off air supplyTechnical Service Service Publications Service HintsWhen Gas Pressure Is Too Low Gas leak. See WarningSF30NT SF30PT SpecificationsLSF30NT, VSF30NT LSF30PT, VSF30PT Replacement Parts AccessoriesParts Central Illustrated Parts Breakdown Parts List LSF20PTWarranty Information Keep this WarrantyQUÉ Hacer SI Percibe Olor a GAS Modelos Modelos Para CocheraTabla DE Contenido Información DE Seguridad Códigos Locales Identificación DEL ProductoDesempaque Características DEL ProductoAire Para Combustión Ventilación Cómo Procurar LA Ventilación AdecuadaConstrucción inusualmente sellada Espacio confinado y no confinadoAire Para Ventilación Aire del interior de la construcción para ventilaciónInstalación Verifique EL Tipo DE GASArtículos DE Instalación Aire del exterior para ventilaciónEn áreas con mucho viento o Ubicación DEL CalentadorInstalación DEL Calentador EN LA Pared Doble en anclaje de pared como se muestra en la figuraColocación del calentador en los tornillos de montaje Coloque el calentador en los tornillos de montajeConexión AL Suministro DE GAS Ventila apuntando hacia abajoRevisión DE LAS Conexiones DE GAS Gas naturalPropano o gas LP Repare todas las fugas inmediatamenteInstale el panel anterior y el refractario Abra la válvula de cierre del equipo consulte la figuraInstalación del panel anterior y el refractario Instrucciones DE Encendido No intente encender ningún aparatoFuncionamiento DEL Inspección DEL CalentadorInspección DEL Limpieza Y MantenimientoEntrada DE Aire AL Piloto DEL Quemador Como se muestra en la figuraSolución DE Problemas Causa Posible RemedioProblema Observado Causa Posible Remedio Baja presión del gasEl termopar está dañado Presione totalmente la perilla de controlEl problema desaparecerá Cierre el suministro de aireSe enciende o se apaga Silbante cuando el quemadorConsejos Para Servicio Servicio TécnicoCuando la presión del gas de entrada sea muy baja SF30NT EspecificacionesLSF30NT, VSF30NT Piezas DE Repuesto AccesoriosCentral DE Piezas Clasificación Ilustrada DE Piezas Lista DE Piezas Información DE Garantía Guarde Esta Garantía

SF20NT specifications

Desa SF20NT is a versatile and innovative gas-fired space heater designed for efficient heating solutions in various environments, whether in residential, commercial, or industrial settings. This model is known for its high performance, energy efficiency, and advanced technology, making it a popular choice among users seeking reliability and effectiveness in their heating needs.

One of the primary features of the Desa SF20NT is its impressive heating capacity. With a heating output of around 20,000 BTUs, it can effectively warm spaces up to 1,000 square feet, making it suitable for larger areas. This capability is enhanced by the heater's superior metal construction, ensuring durability and long-lasting performance.

In terms of technology, the Desa SF20NT incorporates a direct vent system that utilizes outside air for combustion. This feature not only increases efficiency but also enhances safety, as it minimizes the risk of hazardous fumes entering the living space. The direct vent system allows for installation flexibility; the unit can be vented horizontally through a wall or vertically through a roof, catering to different building designs.

Another standout characteristic of the Desa SF20NT is its thermostat control, which allows users to maintain a consistent temperature easily. This feature contributes to energy savings by enabling the heater to operate only when necessary, thus reducing unnecessary heating costs. Additionally, the unit includes a programmable timer, allowing users to set specific heating schedules, further optimizing energy use.

Safety is also a critical aspect of the Desa SF20NT design. It comes with built-in safety features such as a flame sensor and a safety shut-off system, ensuring that the heater operates under safe conditions at all times. The unit is designed to meet stringent safety standards, giving users peace of mind.

In summary, the Desa SF20NT is a powerful, efficient, and safe space heater that is equipped with modern features and technologies. With its high heating capacity, direct vent system, thermostat control, and safety mechanisms, it stands out as an excellent choice for anyone looking for reliable heating solutions. Whether for home or business use, the Desa SF20NT is built to provide comfort and efficiency year-round.