Quadra-Fire QFP44 owner manual Operating Instructions, Gas Fireplace Safety, Your Fireplace

Page 9

User Guide

2Operating Instructions

A. Gas Fireplace Safety

WARNING

HOT SURFACES!

Glass and other surfaces are hot during operation and cool down.

Hot glass will cause burns.

• Do not touch glass until it is cooled

•NEVER allow children to touch glass

•Keep children away

•CAREFULLY SUPERVISE children in same room as appliance.

•Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other ammable materials.

•Keep clothing, furniture, draperies and other combustibles away.

￿This appliance requires the installation of a decorative front with an integral barrier to prevent direct contact with the xed glass panel. Do NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the barrier is not present or help is needed to properly install one.

•Install a physical barrier such as:

-A decorative rescreen.

-Adjustable safety gate.

•Install a switch lock or a wall/remote control with child protection lockout feature.

•Keep remote controls out of reach of children.

• Never leave children alone near a hot replace, whether operating or cooling down.

•Teach children to NEVER touch the replace.

•Consider not using the replace when children will be present.

Contact your dealer for more information, or visit: www. hpba.org/staysafe.

To prevent unintended operation when not using your replace for an extended period of time (summer months, vacations, trips, etc):

•Remove batteries from remote controls.

•Turn off wall controls.

•Unplug 3 volt adapter plug and remove batteries on IPI models.

•Turn off gas controls valve on standing pilot models. When lighting the pilot light on replaces with a standing pilot, remove the xed glass assembly so you can detect presence of residual gas build-up. See Standing Pilot Lighting instructions and Maintenance Tasks.

If you expect that small children or vulnerable adults may come into contact with this replace, the following precau- tions are recommended:

B. Your Fireplace

WARNING! DO NOT operate replace before reading and understanding operating instructions. Failure to operate replace according to operating instructions could cause re or injury.

Decorative Doors

(not shown)

Section 2.E.

Mantel

Fixed Glass Assembly

Section 2.F.

Hearth

(not required)

Clear Space

Section 2.D. Dashboard

Control

Section 2.G.

Figure 2.1 General Operating Parts

Quadra-Fire • QFP44 • 4051-300 Rev M • 09/08

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Installation and Operation ModelsWhat to do if you smell gas Homeowner Reference Information CongratulationsTable of Contents Installer GuideUser Guide Troubleshooting CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Listing and Code Approvals Requirements for the Commonwealth of Massachusetts Gas Fireplace Safety Operating InstructionsYour Fireplace Clear Space Fixed Glass AssemblyDecorative Doors and Fronts Dashboard ControlIgnitor Battery Box Remote OperationCanadian Equipment Requirements Transmitter Remote ReceiverSetting the Clock Transmitter SettingsMatching Security Codes Operating InstructionsSetting Desired Room Temperature Ther- mo Operations Setting F/C ScaleSetting the Countdown Timer Operating the Fan Operates in on or THER- MO modeLow/Battery Indicator Adjusting the Flame Height Operates in on or Thermo modeTransmitter Safety Features Thermo-Updating and Communication-Safety FeaturesBattery Life Timer OperationBefore Lighting Fireplace General Information Transmitter Wall BracketLighting Instructions SP For Your Safety Read Before LightingFrequently Asked Questions Initial Break-in ProcedureAfter Fireplace is Lit Maintenance Tasks-Homeowner Maintenance and ServiceGlass Cleaning Remote ControlMaintenance Tasks-Quali ed Service Technician Standing Pilot Flame Patterns Typical Appliance System Getting StartedDesign and Installation Considerations Tools and Supplies NeededInspect Appliance and Components Select Appliance Location Framing and ClearancesClearances Construct the Appliance ChaseMantel and Wall Projections MantelsMantel Legs or Wall Projections Vent Termination Minimum Clearances Termination LocationsMinimum Clearances for Termination Approved Pipe Vent Information and DiagramsVent Table Key Use of ElbowsVent Diagrams Top Vent Horizontal TerminationOne Elbow Three Elbows Two 45 Elbows replacing One 90 ElbowTop Vent Vertical Termination No ElbowTwo Elbows 12 ft 3.66 m min 60 ft 18.29 m max Pipe Clearances to Combustibles Vent Clearances and FramingWall Penetration Framing Combustible Wall PenetrationInstalling Ceiling Firestop Install the Ceiling FirestopInstall Attic Insulation Shield Flat Ceiling InstallationVaulted Ceiling Installation Secure and Level the Appliance Appliance PreparationAttach Pipe to the Firebox Assembly Install Vent PipeAssemble Vent Sections Assemble Pipe SectionsSlip Section Pilot Holes Assemble Slip SectionsDisassemble Vent Sections Secure the Vent SectionsCaulk Install Metal Roof Flashing13 Assembling the Storm Collar Assemble and Install Storm CollarApply Sealant Top & Partial Sides Install RF4-8Heat Shield Requirements for Horizontal Termination Install Vertical Termination Cap20 Venting through the wall Install Horizontal Termination CapGas Information Kit contentsFuel Conversion Converting to LP Gas44CKP Gas Connection Gas PressureStanding Pilot Ignition System Wiring Wiring RequirementsOptional Accessories Requirements Electrical InformationJunction Box Installation Electrical Service and RepairMantel Leg or Perpendicular Wall FinishingFacing Material Facing Template RemovalMantel Remove Glass Assembly Appliance SetupInstall the Refractory Clean the ApplianceInstall Upper Back Refractory Adjust the Air ShutterInstall Logs, Ember Bed & Rockwool Adjust the Vertical Baf e12 Positioning Right Front Leg Install Andirons Reinstall Glass Install Door FrontsPlace Lava Rock and Vermiculite Standing Pilot Ignition System TroubleshootingSymptom Possible Cause Corrective Action TroubleshootingReference Materials Appliance Dimension DiagramDVP45 Vent Components DiagramsBEK DVP-BEK2 DVP-TVHW DVP-TRAP Parts ServiceDescription Serial # Part Number Service PartsOptional Components Contact Information

QFP44 specifications

The Quadra-Fire QFP44 is a highly efficient and versatile pellet stove designed to provide warmth and comfort while offering a range of advanced features and technologies. It stands out in the market for its blend of efficiency, user-friendly operation, and aesthetic appeal.

One of the key features of the QFP44 is its impressive heat output. With a heating capacity of up to 2,500 square feet, it is suitable for medium to larger living spaces, making it an ideal choice for families looking for an effective heating solution. The stove boasts an adjustable output, allowing users to set the heat level according to their specific needs, which promotes energy efficiency and enhances comfort.

The QFP44 utilizes a patented feed system that ensures a consistent and reliable supply of pellets for combustion. This technology not only maximizes fuel efficiency but also minimizes the need for frequent refueling. In addition, the stove features a large hopper capacity, capable of holding up to 45 pounds of pellets. This translates into longer burn times, enabling users to enjoy hours of warmth without constant supervision.

Another notable characteristic of the QFP44 is its advanced control system. The innovative electronic control board allows users to monitor and adjust the stove settings easily. The system includes programmable temperature settings, which enable homeowners to schedule heating times according to their lifestyle. This convenience makes the stove ideal for those who want to return to a warm home without wasting energy.

The QFP44 is also engineered with a clean-burning technology that significantly reduces emissions. This feature not only makes the stove environmentally friendly but also enhances its safety profile. The high-efficiency combustion system effectively converts pellets into heat with minimal smoke and pollutants, fulfilling strict environmental standards.

For aesthetic appeal, the QFP44 is designed with a contemporary look, featuring a large viewing window that allows users to enjoy the beautiful ambiance of the flame. The stove is available in various finishes, making it a stylish addition to any home décor.

Overall, the Quadra-Fire QFP44 combines efficiency, user-friendly technology, and an elegant design, making it a top choice for anyone seeking an effective and attractive pellet heating solution. Its blend of features ensures homeowners can enjoy both comfort and convenience during the cold months while maintaining an environmentally responsible heating option.
Top Page Image Contents