Quadra-Fire QV-ST, QV-PIER owner manual The Gas Control System

Page 29
Step 5. The Gas Control System

Step 4. Positioning, Leveling, and Securing the Fireplace

The diagram below shows how to properly position, level, and secure the fireplace.

NAILING

TABS

(BOTH SIDES)

Figure 31. Proper Positioning, Leveling, and

Securing of a Fireplace

Place the fireplace into position.

Level the fireplace from side to side and from front to back.

Shim the fireplace with non-combustible material, such as sheet metal, as necessary.

Secure the fireplace to the framing by nailing or screwing.

Holes are provided in the base pan for securing the unit to the floor.

Step 5. The Gas Control System

!WARNING: THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

IPI PILOT

FLAME

 

SENSOR

 

ROD

Figure 32. Gas Control System

Intermittent Pilot Ignition (IPI) System

This system includes a 3V control valve, electronic module and intermittent pilot.

!WARNING: CONTINUOUS 110-120 VAC SERVICE MUST BE WIRED DIRECTLY TO

THE FIREPLACE JUNCTION BOX IN A IPI SYSTEM.

Quadra-FireQV-PIER, QV-ST Series: HV-IPI2005-901 Rev. G • 2/06

29

Image 29
Contents What to do if you smell gas Models QV-Pier QV-ST Series HV-IPIPROHIBITED Safety and Warning InformationTable of Contents 6 Log Assembly Service Parts ListQV-Pier-HV-IPI QV-PIER-HV-IPI ACCESSORIESCOMMON PART SERIAL #11710 Service PartsQV-ST-HV-IPI NG, LP Exploded Parts DiagramQV-ST-HV-IPI QV-ST-HV-IPI Service PartsQV-PIER-HV-IPI Installation Codes 1Approvals and CodesHigh Altitude Installations Appliance CertificationIntroducing the Quadra-FireGas Fireplaces 2Getting StartedPre-installPreparation Diagram of the QV-PIER-HV-IPI ELECTRICAL ACCESS GAS LINE ACCESSTOP STANDOFFS REAR VENTStep 1. Locating the Fireplace 3Installing the FireplaceStep 2. Framing the Fireplace QV-PIER-HV-IPI Model35-3/4 QV-ST-HV-IPIDVP90ST NOTE PIPES OVERLAP 1-1/4INCHES AT EACH JOINTA. Vent System Approvals Step 3. Installing the Vent SystemTEMS OR COMPONENTS MAY BE USED Identifying Vent ComponentsFlue Restrictor Instructions Figure 14. Venting with One 90 Elbow Figure 13. Venting with One 90 ElbowFigure 15. Venting with Two 90 Elbows Figure 17. Venting with Two 90 Elbows Venting with Two 90 ElbowsFigure 18. Venting with three 90 elbows Figure 19. Venting with three 90 elbows Venting Out Vertically B. Installing Vent Components2. Continue Adding Vent Components Figure 25 Hole & New Framing Members Figure 29. Vent Termination Minimum Clearances = AREA WHERE TERMINAL IS NOT PERMITTED= VENT TERMINAL X = AIR SUPPLY INLETMark the roof hole accordingly Step 5. The Gas Control System Natural Gas PressurePropane 5.0 inchesFor Intermittent Pilot Ignition Wiring Step 8. Wiring the FireplaceOperation using Battery Power Appliance RequirementsOptional Accessories Figure 35. Fan Wiring DiagramFan Installation Wall SwitchFigure 40. Sealant Material Hearth Extensions Step 9. FinishingIN ANY MANNER ANDIRON TABS 1/2”ANDIRONS Page Placing the Ember Material Figure 53. Placement of the Ember MaterialStep 12. Lighting the Fireplace After the InstallationStep 11. Before Lighting the Fireplace Fireplace Maintenance 4Maintaining and Servicing Your FireplaceSymptom 5 TroubleshootingPossible Causes Corrective ActionsIntellifire Ignition System - continued SymptomPossible Causes Corrective ActionsLIMITED LIFETIME WARRANTY Lifetime WarrantyTHREE YEAR WARRANTY TWO YEAR WARRANTY