Quadra-Fire QV-PIER Top Standoffs, Rear Vent, Collars, Gas Line Access, Electrical Access, 205mm

Page 12

(205mm)

			5-14
			(133mm)	1/2
				1/2
				(13mm)
				(4)
		12
		(306mm)
		Ø8
		(205mm)
		12
		(305mm)
		Ø8	46-5/8
		(205mm)	(1183mm)
		ELECTRICAL
		ACCESS
			32-5/16
34-3/4		42	(821mm)	4-1/2
34-3/4		42		(114mm)
(882mm)		(1067mm)		21-9/16
		GAS LINE		(548mm)
		ACCESS		(548mm)
		ACCESS
				8-1/2
				(216mm)
4-1/16		2-5/16	36-3/16	24
4-1/16		(58mm)	(919mm)	(610mm)	2-9/16
(102mm)					(64mm)
4-1/2		4-3/4
(114mm)		(121mm)
Figure 2.		Dimensions of the QV-ST-HV-IPI
	TOP VENT
	COLLARS
		TOP STANDOFFS		REAR VENT
				REAR VENT
				COLLARS

GAS CONTROLS	SIDE GLASS
& LABELS	DOOR

GAS LINE

ACCESS

Figure 3. Diagram of the QV-ST-HV-IPI

ELECTRICAL

ACCESS

12	Quadra-Fire • QV-PIER, QV-ST Series: HV-IPI • 2005-901 Rev. G • 2/06

Image 12

Contents Models QV-Pier QV-ST Series HV-IPI What to do if you smell gasSafety and Warning Information PROHIBITEDTable of Contents Service Parts List QV-Pier-HV-IPI6 Log Assembly ACCESSORIES QV-PIER-HV-IPICOMMON PART SERIAL #Service Parts 11710QV-ST-HV-IPI NG, LP Exploded Parts DiagramQV-ST-HV-IPI Service Parts QV-PIER-HV-IPIQV-ST-HV-IPI 1Approvals and Codes Installation CodesHigh Altitude Installations Appliance Certification2Getting Started Pre-installPreparationIntroducing the Quadra-FireGas Fireplaces Diagram of the QV-PIER-HV-IPI GAS LINE ACCESS ELECTRICAL ACCESSTOP STANDOFFS REAR VENT3Installing the Fireplace Step 1. Locating the FireplaceStep 2. Framing the Fireplace Model QV-PIER-HV-IPI35-3/4 QV-ST-HV-IPINOTE PIPES OVERLAP 1-1/4INCHES AT EACH JOINT DVP90STStep 3. Installing the Vent System A. Vent System ApprovalsTEMS OR COMPONENTS MAY BE USED Identifying Vent ComponentsFlue Restrictor Instructions Figure 13. Venting with One 90 Elbow Figure 14. Venting with One 90 ElbowFigure 15. Venting with Two 90 Elbows Venting with Two 90 Elbows Figure 17. Venting with Two 90 ElbowsFigure 18. Venting with three 90 elbows Figure 19. Venting with three 90 elbows B. Installing Vent Components Venting Out Vertically2. Continue Adding Vent Components Figure 25 Hole & New Framing Members = AREA WHERE TERMINAL IS NOT PERMITTED Figure 29. Vent Termination Minimum Clearances= VENT TERMINAL X = AIR SUPPLY INLETMark the roof hole accordingly Step 5. The Gas Control System Pressure Natural GasPropane 5.0 inchesStep 8. Wiring the Fireplace For Intermittent Pilot Ignition WiringOperation using Battery Power Appliance RequirementsFigure 35. Fan Wiring Diagram Optional AccessoriesFan Installation Wall SwitchStep 9. Finishing IN ANY MANNERFigure 40. Sealant Material Hearth Extensions 1/2” ANDIRONSANDIRON TABS Page Figure 53. Placement of the Ember Material Placing the Ember MaterialAfter the Installation Step 11. Before Lighting the FireplaceStep 12. Lighting the Fireplace 4Maintaining and Servicing Your Fireplace Fireplace Maintenance5 Troubleshooting SymptomPossible Causes Corrective ActionsSymptom Intellifire Ignition System - continuedPossible Causes Corrective ActionsLifetime Warranty LIMITED LIFETIME WARRANTYTHREE YEAR WARRANTY TWO YEAR WARRANTY