Samsung SSA-R2010/EXP manual Display and Operation Status of READER/REGISTER, Registration Mode

Page 21

DISPLAY AND OPERATION STATUS OF READER/REGISTER

LED ON :

 

LED OFF :

 

LED Blinking :

 

 

 

 

 

 

 

LED

Beep

 

Voice Message

Description

PWR

OK

ERR

WELCOME TO ACCESS

The product is in the boot process after it

 

 

1 BEEP

 

 

CONTROL SYSTEM

turned on.

 

 

 

PWR

OK

ERR

 

Restores registered user cards and other

 

 

X

SYSTEM INITIALIZED

 

 

system settings to the default.

 

 

 

 

REGISTRATION MODE

 

LED

Beep

Voice Message

Description

PWR

OK

ERR

MASTER ID REGISTRATION MODE

The first card read by the product after it is

 

 

X

Initialized will be registered as the master

 

 

 

 

card.

PWR

OK

ERR

REGISTRATION AND DELETION MODE,

 

 

 

X

You can register or remove the user card.

 

 

SCAN YOUR CARD

 

 

 

 

PWR

OK

ERR

ID REGISTERED

The user card is registered successfully.

 

 

3 BEEPS

 

 

 

 

 

 

 

 

 

 

 

 

 

PWR

OK

ERR

 

3 BEEPS

FINGERPRINT REGISTERED

The user card/fingerprint is registered

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

successfully.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PWR

OK

ERR

 

2 BEEPS

FINGERPRINT REGISTRATION

Failed to register the user card/fingerprint.

 

 

 

 

 

 

 

 

 

 

 

 

 

FAILED, PLEASE TRY AGAIN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PWR

OK

ERR

 

4 BEEPS

ID DELETED

The user card/fingerprint is deleted

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

successfully.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

READER MODE

 

 

 

 

LED

 

 

 

Beep

Voice Message

Description

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PWR

OK

ERR

 

 

X

READER MODE

User card will be authenticated in normal

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

operation mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PWR

OK

ERR

 

 

1 BEEP

ACCESS GRANTED

User access is granted

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PWR

OK

ERR

 

 

2 BEEPS

ACCESS DENIED,

User access is denied

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PLEASE TRY AGAIN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PWR

OK

ERR

 

 

2 BEEPS

ID UNREGISTERED

Unregistered user

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INITIALIZATION

English _ 21

Image 21
Contents Please visit our website Biometric ReaderSafety information Safety informationThis device may not cause harmful interference, Important Safety InstructionsContents Product introduction FeaturesWHAT’S Included Cables Quick Guide CD ManualMaster Card Ferrite Cores X AT a Glance Front PanelDisplays the status of the system operation Rear Panel Cable Color Scheme Pins Signal Cable ColorCable Selection Termination Resistor Installing the Wall MountHost PC EARTH-GROUNDING the Communication CablesConnection Overall Wiring DiagramInput Connection PowerController Connection of External LED controlWiegand Data Output Connection Output ConnectionExternal Reader Connection Connecting to the External ReaderRS-485 Communication Port Connection Standalone Communication Line ConnectionRS-485 Communication Port Connection Multiple Units Hub Host PC RJ45 RJ45 RJ45 TCP/IP Communication Port ConnectionRefer to Communication Address Setup. on Initializing the System Using the DIP SwitchInitialization Master IDRegistration Mode Reader ModeDisplay and Operation Status of READER/REGISTER To REGISTER/DELETE the Master ID Card Communication Address SetupReader Mode and Authentication If the card is not registeredPresent the registered card to the reader User management Registering the IDTo Register the ID Card Along with the Fingerprint Successfully To Delete IDTiming Diagram Wiegand Output DefaultOutput format Data Type 26-bit /34-bitOther information HOW to Register the FingerprintTroubleshooting TroubleshootingProblem Action Problem Product specifications Product SpecificationsCorrect disposal of batteries in this product