Samsung SSA-R2010/EXP manual Important Safety Instructions

Page 3

7.Avoid aiming the controller directly towards extremely bright objects such as sun.

8.Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.

9.The Mains plug is used as a disconnect device and shall stay readily operable at any time.

FCC Statement

Caution : Any changes or modifications in construction of this device which are not expressly approved by the

party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1)This device may not cause harmful interference, and

2)This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, any cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

IMPORTANT SAFETY INSTRUCTIONS

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

13. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

SAFETY INFORMATION

English _ 3

Image 3
Contents Please visit our website Biometric ReaderSafety information Safety informationThis device may not cause harmful interference, Important Safety InstructionsContents Product introduction FeaturesWHAT’S Included Cables Quick Guide CD ManualMaster Card Ferrite Cores X AT a Glance Front PanelDisplays the status of the system operation Rear Panel Cable Color Scheme Pins Signal Cable ColorCable Selection Termination Resistor Installing the Wall MountHost PC EARTH-GROUNDING the Communication CablesConnection Overall Wiring DiagramConnection of External LED control PowerInput Connection ControllerWiegand Data Output Connection Output ConnectionExternal Reader Connection Connecting to the External ReaderRS-485 Communication Port Connection Standalone Communication Line ConnectionRS-485 Communication Port Connection Multiple Units Hub Host PC RJ45 RJ45 RJ45 TCP/IP Communication Port ConnectionMaster ID Initializing the System Using the DIP SwitchRefer to Communication Address Setup. on InitializationRegistration Mode Reader ModeDisplay and Operation Status of READER/REGISTER To REGISTER/DELETE the Master ID Card Communication Address SetupReader Mode and Authentication If the card is not registeredPresent the registered card to the reader User management Registering the IDTo Register the ID Card Along with the Fingerprint Successfully To Delete IDData Type 26-bit /34-bit Wiegand Output DefaultTiming Diagram Output formatOther information HOW to Register the FingerprintTroubleshooting TroubleshootingProblem Action Problem Product specifications Product SpecificationsCorrect disposal of batteries in this product