Napoleon Fireplaces GD19N, GD19P Charcoal Embers, Vermiculite, Glowing Embers, Logo Placement

Page 27
CHARCOAL EMBERS

3.Place the center log as shown, ensuring the holes on the underside are placed onto the two center pins.

4.Place the hole in the underside of the right log onto the locating pin, on the burner base and rests against the rear log as shown.

5.Re-install the glass door.

CHARCOAL EMBERS

Randomly place the charcoal embers along the front and sides of the burner in a realistic manner. Fine dust found in the bottom of the bag should not be used.

VERMICULITE

Sprinkle vermiculite around the charcoal embers.

Note: Both charcoal embers and vermiculite are not to be placed on the burner ports.

GLOWING EMBERS

Tear the embers into pieces and place along the burner ports covering all of the burner. Care should be taken to shred the embers into thin, small irregular pieces as only the exposed edges of the fibre hairs will glow. The ember material will only glow when exposed to direct flame; however, care should be taken to not block the burner ports.

Blocked burner ports can cause an incorrect flame pattern, carbon deposits and delayed ignition. PhazerTM logs glow when exposed to direct flame. Use only certified "glowing embers" and PhazerTM logs available from your Napoleon® dealer.

LOGO PLACEMENT

 

 

 

 

 

 

 

FIGURE 61

Remove the backing of the

 

 

 

 

 

 

1/2"

 

1/2"

logo supplied and place on

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the glass viewing door, as

 

 

 

 

 

 

 

 

 

 

 

 

LOGO

 

 

 

 

 

indicated.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

27

CONTROL FUNCTIONS

FAN

 

 

CONTROL

 

 

(OPTION)

 

 

FLAME

NIGHT

 

ADJUSTMENT

MAIN

 

LIGHTTM

FIGURE 62

SWITCH

BURNER

SWITCH

 

 

MAIN BURNER SWITCH

This switch turns the Main Burner on and off.

FLAME ADJUSTMENT

Turn this knob clockwise or counter-clockwise to adjust the main burner flame height.

NIGHT LIGHTTM SWITCH

This switch turns the Night LightTM on and off.

FAN CONTROL OPTION

If installed this switch will turn on and off the power to the blower and control the fan speed. There is also a thermally activated switch that will only let the blower come on once the unit has reached a comfortable temperature.

W415-0612 / C / 01.25.08

Image 27
Contents GD19P INSTALLATION AND OPERATION INSTRUCTIONSSAFETY INFORMATION GD19NRETAIN THIS MANUAL FOR FUTURE REFERENCE TABLE of CONTENTSCONDITIONS AND LIMITATIONS GENERAL INSTRUCTIONS GENERAL INFORMATIONCARE OF GLASS AND PLATED PARTS VENTING FOR SPECIFIC VENTING PARAMETERS, REFER TO PAGES VENT INSTALLATIONSHORIZONTAL VENT SECTIONS VERTICAL VENT SECTIONSTOP EXIT TYPICAL VENT INSTALLATIONSSPECIAL VENT INSTALLATIONS REAR EXITW415-0612 /C MINIMUM AIR TERMINAL LOCATION CLEARANCESTOP EXIT VENTING APPLICATION FLOW CHARTFIREPLACE VENT EXIT REAR EXITHT VT TOP EXIT / HORIZONTAL TERMINATIONDEFINITIONS ELBOW VENT LENGTH VALUESTOP EXIT / HORIZONTAL TERMINATION REAR EXIT / HORIZONTAL TERMINATION H2HT VT REAR EXIT / HORIZONTAL TERMINATION HT VT TOP OR REAR EXIT VERTICAL TERMINATIONHT VT TOP EXIT CONVERSION 3/4” INSTALLATION WALL AND CEILING PROTECTIONHORIZONTAL INSTALLATION VERTICAL INSTALLATIONUSING FLEXIBLE VENT COMPONENTS HORIZONTAL AIR TERMINAL INSTALLATIONVERTICAL AIR TERMINAL INSTALLATION FIREPLACE VENT CONNECTION EXTENDED HORIZONTAL AND CORNER VERTICAL VENTING INSTALLATIONAIR TERMINAL INSTALLATION RESTRICTING VERTICAL VENTSOPTIONAL WALL SWITCH INSTALLATION MOBILE HOME INSTALLATIONGAS INSTALLATION ELECTRICAL INSTALLATIONCombustible Framing 0 to stand-offs FRAMINGREAR VENT TOP VENTFIGURES 41a&b MINIMUM MANTEL AND ENCLOSURE CLEARANCESFIREBOX FRONT FACING AND INSET KIT INSTALLATIONLENS ASSEMBLY INSTALLATION BLOWER INSTALLATIONNIGHT LIGHT REPLACEMENT BULB REPLACEMENTLOG PLACEMENT FINISHINGGLASS DOOR INSTALLATION AND REMOVAL DOOR GLASS REPLACEMENTNIGHT LIGHTTM SWITCH LOGO PLACEMENTMAIN BURNER SWITCH FLAME ADJUSTMENTSee detail for optional wall switch GD-660wiring WIRING DIAGRAMOPERATING INSTRUCTIONS OPERATION / MAINTENANCEMAINTENANCE FOR YOUR SAFETY READ BEFORE OPERATINGFLAME ADJUSTMENT ADJUSTMENTSPILOT INJECTOR AND ORIFICE REPLACEMENT VENTURI ADJUSTMENTFOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OF REPLACEMENTSREPLACEMENT PARTS ACCESSORIESW415-0612 /C TEST SOLUTION TROUBLE SHOOTING GUIDESYMPTOM PROBLEMPilot lights SYMPTOMPROBLEM TEST SOLUTIONW415-0612 /C Fireplace Service Historyserviced annually depending on usage This fireplace must beW415-0612 /C