Napoleon Fireplaces GD19N, GD19P Blower Installation, Night Light Replacement, Bulb Replacement

Page 25
BLOWER INSTALLATION

25

BLOWER INSTALLATION

ELECTRICAL INSTALLATION TO BE DONE BY A QUALIFIED INSTALLER and must be connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.

If an optional blower is to be used, the blower must be connected to the main power supply. Route a grounded 14 gauge 2- wire power cable to the junction box and ground. At the point where the cable enters the junction box, a conduit connector must be provided.

1.Remove the two screws that secure the control panel to the front of the unit.

FIGURE 52

GS66 WIRING DIAGRAM

4. Place the thermal disk assembly onto the stud located at the lower left of the firebox and behind the support bracket.

5. Connect the wiring for the variable speed switch.

VARIABLE SPEED SWITCH

VARIABLE

SPEED SWITCH

KNOB

RED

THERMAL DISK

WHITE

BLACK

WHITE

6. Insert the blower assembly into the left side under the firebox, slide into the clip and place onto the same stud used for the thermal disk assembly. Secure with the lock washer and wing nut supplied. Ensure that the blower does not touch

 

WIRE

 

 

HARNESS

 

 

(included in GS66 kit)

BLOWER

 

TO

FIGURE 53

POWER

 

SUPPLY

2.Connect the black and red wires of the wire harness to the prongs on the blower.

3.Connect the white and black wires of the wire harness to the prongs on the thermodisc.

the base of the firebox, any wiring or

FIGURE 54

controls. Ensure that the thermodisc is

 

touching the wall of the firebox.

 

HINT: Rest the thermal disk assembly forward against the support bracket.

7.Place the variable speed switch into position and secure with the pal nut supplied. (FIGURE 25) Reinstall the control panel and install the variable speed switch knob.

NOTE: Plug into the receptacle on the right side of the unit.

NIGHT LIGHTREPLACEMENT

BULB REPLACEMENT

The GD19 comes equipped with our “Night Light™”. If in the event the lamp or lens needs to be replaced, follow these instructions.

1.Turn off all electrical supply.

2.Remove the front and door from the firebox.

3.Unscrew the lens cover making sure the washer stays in place.

Note: Do not handle the lamp (bulb) with bare fingers, protect with a clean dry cloth.

4.The lamp will pull straight out of the socket. Replace with Wolf Steel Ltd. parts only (W387-0006), as lamp and lens are special "high temperature" products .

5.Replace lens with gasket, lense covers, attach wires to quick connects and replace the door when finished.

THE FIREBOX MUST BE SEALED.

FIGURE 55 When re-assembling the light assembly, care must be taken. “Light Leakage” from above the cast doors may be noticed. The holes in the lamp housing are necessary for ventilation and must not be covered.

LENS ASSEMBLY INSTALLATION

1. Remove the door from

KEY HOLE

FIGURE 56

the firebox.

 

 

2.Run the wires up through the lens hole.

3.Align key hole with lens assembly.

4.Snap into place.

5.Replace light shields,

attach the wires and replace the door to the firebox.

LENS ASSEMBLY REPLACEMENT

1. Remove the front door

FIGURE 57

and top shield from the

 

firebox.

 

2.Compress the retainer fins in with a screw driver while pressing firmly on the top of the light assembly.

3.Once all the retainer fins are pushed in the lens assembly will snap out of place.

W415-0612 / C / 01.25.08

Image 25
Contents SAFETY INFORMATION INSTALLATION AND OPERATION INSTRUCTIONSGD19N GD19PRETAIN THIS MANUAL FOR FUTURE REFERENCE TABLE of CONTENTSCONDITIONS AND LIMITATIONS GENERAL INFORMATION GENERAL INSTRUCTIONSCARE OF GLASS AND PLATED PARTS VENTING HORIZONTAL VENT SECTIONS VENT INSTALLATIONSVERTICAL VENT SECTIONS FOR SPECIFIC VENTING PARAMETERS, REFER TO PAGESSPECIAL VENT INSTALLATIONS TYPICAL VENT INSTALLATIONSREAR EXIT TOP EXITW415-0612 /C MINIMUM AIR TERMINAL LOCATION CLEARANCESFIREPLACE VENT EXIT VENTING APPLICATION FLOW CHARTREAR EXIT TOP EXITDEFINITIONS TOP EXIT / HORIZONTAL TERMINATIONELBOW VENT LENGTH VALUES HT VTTOP EXIT / HORIZONTAL TERMINATION H2 REAR EXIT / HORIZONTAL TERMINATIONHT VT REAR EXIT / HORIZONTAL TERMINATION HT VT TOP OR REAR EXIT VERTICAL TERMINATIONHT VT TOP EXIT CONVERSION HORIZONTAL INSTALLATION INSTALLATION WALL AND CEILING PROTECTIONVERTICAL INSTALLATION 3/4”HORIZONTAL AIR TERMINAL INSTALLATION USING FLEXIBLE VENT COMPONENTSVERTICAL AIR TERMINAL INSTALLATION FIREPLACE VENT CONNECTION AIR TERMINAL INSTALLATION VERTICAL VENTING INSTALLATIONRESTRICTING VERTICAL VENTS EXTENDED HORIZONTAL AND CORNERGAS INSTALLATION MOBILE HOME INSTALLATIONELECTRICAL INSTALLATION OPTIONAL WALL SWITCH INSTALLATIONREAR VENT FRAMINGTOP VENT Combustible Framing 0 to stand-offsFIGURES 41a&b MINIMUM MANTEL AND ENCLOSURE CLEARANCESFIREBOX FRONT FACING AND INSET KIT INSTALLATIONNIGHT LIGHT REPLACEMENT BLOWER INSTALLATIONBULB REPLACEMENT LENS ASSEMBLY INSTALLATIONGLASS DOOR INSTALLATION AND REMOVAL FINISHINGDOOR GLASS REPLACEMENT LOG PLACEMENTMAIN BURNER SWITCH LOGO PLACEMENTFLAME ADJUSTMENT NIGHT LIGHTTM SWITCHSee detail for optional wall switch GD-660wiring WIRING DIAGRAMMAINTENANCE OPERATION / MAINTENANCEFOR YOUR SAFETY READ BEFORE OPERATING OPERATING INSTRUCTIONSPILOT INJECTOR AND ORIFICE REPLACEMENT ADJUSTMENTSVENTURI ADJUSTMENT FLAME ADJUSTMENTREPLACEMENT PARTS REPLACEMENTSACCESSORIES FOR WARRANTY REPLACEMENT PARTS, A PHOTOCOPY OFW415-0612 /C SYMPTOM TROUBLE SHOOTING GUIDEPROBLEM TEST SOLUTIONPROBLEM SYMPTOMTEST SOLUTION Pilot lightsserviced annually depending on usage Fireplace Service HistoryThis fireplace must be W415-0612 /CW415-0612 /C