Vermont Casting RUVS40 manual General Information, Vent Free Features, Quick Installation

Page 5

General Information

Vent Free Features

The Radiance RUVS40 is an unvented gas heating appliance tested and listed to the ANSI standard Z21.11.2a 1997. This appliance is specifically configured to burn either Natural Gas or Propane fuel, as indicated on the metal rating plate attached to the rear shroud. The Radiance RUVS40 is not fuel convertible.

The Radiance burner controls are conveniently located and easy to operate. As illustrated in Figure 1, the front lip of the heater swings down to reveal the gas valve controls and piezo pilot ignitor. Once the standing pilot is lit, the heater can be set for either manual or thermostatic operation using the convenient toggle switch (Fig. 3) at the rear of the unit. A variable regula- tor allows you to adjust burner heat output between HIGH, (35,000 BTU), and LOW, (26,000 BTU). See the Operation section for details.

A push button Piezo ignitor is used to light the standing pilot. The pilot incorporates an Oxygen Depletion System (ODS/pilot) which will shut off gas flow to the burner in the event that sufficient fresh air becomes unavailable for continued safe operation.

Quick Installation

Your Radiance Vent Free heater is shipped completely assembled and ready for installation. You must, however, locate the heater in accordance with the specifications detailed in the next section of this manual. Connection to the gas supply must be made only by a qualified gas technician and only after verification that the minimum combustion air and ventilation requirements have been met.

Optional Fan Kit #2767 /FK26

This accessory will help distribute heated air from within the firebox out into the room. The fan is con- trolled by a snapstat that turns power on and off as the firebox temperature rises above and falls below a preset temperature. A rheostat provides for variable fan speeds up to 160 cfm.

Optional

Glass / Catalyst Kit RGDCFK

The glass panel replaces the standard screen. The catalytic combustor installs easily into the upper manifold above the firebox. Ask your dealer for details.

Vermont Castings Radiance

 

HI

Piezo Ignitor

 

Valve Control

Regulator

 

Radiance

 

ON

 

PILOT

 

OFF

 

ST174/183

Fig. 2 Radiance rating plate and control panel.

T'STAT

OFF

ON

ST182

Fig. 3 Remote burner switch.

5

Image 5
Contents Radiance Table of Contents Fuel Type SpecificationsRadiance Unvented Gas Heater RUVS40 Carbon Monoxide Poisoning MAY Lead to Death Safety InformationQuick Installation Vent Free FeaturesGeneral Information Optional Fan Kit #2767 /FK26Fresh Air Requirements for Combustion and Ventilation Installation RequirementsProvide For Adequate Ventilation Unusually Tight ConstructionVent options to provide additional air Hearth Requirements Minimum Clearances to Combustible MaterialsFreestanding Stove Alcove ClearancesHardware Bag Contents AssemblyUnpacking the Radiance Remove the Front, Screen and LogsKit Contents used with the RUVS40 Install Optional Fan, #2767/FK26Install the Control Switch. Fig AA DResecure the Rear Shroud panels Attach the fan assembly to the fan bracketConnect the Gas Line Thermostat Connection optionalRemove the valve cover plate Install the LogsReplace the front panel Complete the InstallationPilot and Burner Inspection OperationYour First Fire For Your Safety Read Before Lighting Trouble No spark at Pilot when Ignitor is operatedOdor During Operation TroubleshootingCondition Possible Cause Solution Cleaning Procedure Firebox Cleaning and InspectionGlass Replacement Care of Cast IronCatalytic Combustor Clean the combustor moduleRemove the combustor module Replace the combustor moduleRadiance Vent Free Gas Heater RUVS40 #10-24 X 1/4 Phil. Pn Hd Screw RUVS40Limited One Year Warranty Limited Three Year WarrantyHow To Obtain Service Exclusions and LimitationsVermont Castings Majestic Products Company