Jotul GF 400 DV manual Connect power cord to outlet, Short phillips screwdriver

Page 25

Optional Blower # 156000

Connect the gas supply line to the stove, before installing the Blower.

Use a 90° Elbow off the control valve to create clearance required for the blower installation.

1.Unpack and check the contents of the blower kit. Contact your dealer if any damage is evident or parts are missing. See fig. 42.

2.Attach the Snapstat Bracket to the studs located in the middle of the firebox floor using the two M6 hex nuts and a 10 mm wrench. See fig. 43.

3.Attach the Blower Bracket to the stove using the two M6 flange head hex bolts as shown in fig. 43.

4.Attach the Duct Deflectors using the two #7 x 1/2” screws together with the finger guard mounting screws already in place. See #7 and #11 in fig. 42.

5.Install the Blower with the duct openings oriented up and forward. See fig. 44. Feed the wire harness through the bracket opening and secure the blower to the bracket with the wingscrew.

6.Attach either Snapstat wire connector to either Snapstat terminal. See fig. 44.

7.Install the Snapstat by sliding it all the way into the slot in the bottom of the Snapstat Bracket as shown in figs. 42 and 44.

8.Connect the male wire harness connector to the female wire harness connector already installed in the stove. See fig. 44.

9. Connect power cord to outlet.

„THIS BLOWER MUST BE ELECTRICALLY GROUNDED IN ACCORDANCE WITH LOCAL CODES OR, IN THE ABSENCE OF LOCAL CODES, WITH THE CURRENT ANSI/NFPA 70, NATIONAL ELECTRICAL CODE OR CSA C22.1-CANADIAN ELECTRICAL CODE.

„THIS UNIT IS SUPPLIED WITH A THREE-PRONG (GROUNDING) PLUG FOR PROTECTION AGAINST SHOCK HAZARD AND SHOULD BE PLUGGED DIRECTLY INTO A PROPERLY GROUNDED THREE-PRONG RECEPTACLE. DO NOT CUT OR REMOVE THE GROUNDING PRONG FROM THE PLUG.

„ALWAYS DISCONECT THE POWER SUPPLY WHEN PERFORMING ANY SERVICE ON THE FIREPLACE INSERT.

6

7

 

5

 

 

8

 

 

 

 

 

11

 

 

 

 

1

 

 

2

 

3

 

 

 

 

9

 

 

 

 

 

 

 

4

 

 

 

 

 

7

10

Contents

Tools Required

 

1.

Blower

• 10 mm wrench

 

2.

Mounting Bracket

* short phillips screwdriver

3.

Snapstat Wire Harness

*

Safety Glasses

 

4.

Control Switch Wire Harness

 

*

Work Gloves

 

5.

Snapstat

 

 

 

 

6.

Snapstat Bracket

 

 

 

7.

Blower Duct Deflector (2)

 

 

 

8.

M6 Hex Head Flange Nuts (2)

 

 

 

9.

M6 x 12 Hex Head Flange Bolts (2)

 

 

10. M6 x 12 Wingscrew

11. #7 x 1/2” phillips screw (2)

Figure 42. Blower Kit Components

Hex Head

Flange Bolts

Snapstat

Bracket

Hex Head

Flange Nuts

Blower Bracket

Figure 43. Attach Snapstat and Blower Brackets.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Jøtul GF 400 DV Sebago Gas Heater Welcome to Jøtul Jøtul GF 400 DV Sebago Direct Vent Gas Heater Table of ContentsSuggested Tools for Installation and Service GF 400 DV Sebago SpecificationsInput Rates Unpacking your stove Hardware Bag ContentsGlass Panel Location Safety InformationHearth Requirements Minimum Clearances from the Vent Pipe to Combustibles Alcove InstallationHorizontal Run Vertical RunVent Restriction Venting RequirementsIntake Air Restrictor Exhaust RestrictorFront LEG Back Vertical Vent Termination„ Minimum Vertical run must be at least 8 ft .43 m Vertical Termination for Vent Termination Zones Natural GasVenting Must Terminate END Within the Shaded Area Vent Termination Zones PropaneThese installation requirements must be followed Co-linear Vent InstallationMasonry or Prefabricated Chimney Conversion Snorkel Terminations Horizontal Termination„ With a 14 Snorkel „ With a 36 SnorkelMin inches, U.S. / *12 inches 30 cm can Horizontal Termination ClearanceConversion Kit Contents Mobile Home InstallationTools required Regulator tower labeled for propane Regulator tower screws#33 for NG Mm for LPG Fuel Conversion ProcedureBurner Plate Brass Elbow Burner OrificeGas Supply Connection Adjust the Air ShutterNever USE AN Open Flame to Check for GAS Leaks Gas Pressure High Altitude AdjustmentLeak test Always Test Pressures with Valve Control Knob SET on HighOptional Wall Thermostat or Remote Control Flame Appearance / Air Shutter AdjustmentRemote Control FrontInstall Right Log Log Set InstallationProper pilot flame appearance System CheckLighting of the appliance. This fog will disappear as OperationGlass Care Annual CleaningVent System Burner and LogsetShort phillips screwdriver Connect power cord to outletBlower Operation Wingscrew Snapstat Connectors Male QuickconnectorBlocking the Pilot Assembly Opening Install the Rear PanelReplace the Glass Frame Replace the Top PlateGF 400 DV Sebago Illustrated Parts Breakdown GF 400 DV Sebago Parts List Serial Number Name of InstallerDate of Purchase Purchased fromControl Valve What to do if YOU Smell GASPush in gas control knob slightly and turn clockwise toOFF Jøtul AS November 2005 137750-EBox Fredrikstad Norway Jøtul North America

GF 400 DV specifications

The Jotul GF 400 DV is a highly sought-after gas stove, known for its excellent efficiency and stylish design. This innovative heating solution combines traditional aesthetics with modern technology to create a product that is not only functional but also enhances any living space.

One of the standout features of the Jotul GF 400 DV is its elegant cast iron construction. The durability of cast iron ensures that the stove retains heat longer, providing warmth even after the fire goes out. The design incorporates a large viewing window that allows for an unparalleled view of the flames, fostering a cozy atmosphere. The stove is available in several finishes, including classic black, which complements a variety of home decors.

Efficiency is a key characteristic of the GF 400 DV, as it is designed to achieve a high thermal efficiency rating. It utilizes direct venting technology, allowing for easy installation and efficient combustion. This technology facilitates the venting of exhaust gases outside the home, ensuring indoor air quality remains pristine. The adjustable heat output allows users to customize the warmth according to their needs.

Another impressive feature of the Jotul GF 400 DV is the inclusion of a variable flame adjustment system. This system enables users to control the intensity of the flames, providing both ambiance and practicality. The stove can produce up to 25,000 BTUs, making it suitable for heating medium to large spaces, with an estimated heating area of around 800 to 1,500 square feet.

The GF 400 DV is equipped with electronic ignition for hassle-free startup. Additionally, it features a remote control option, allowing users to operate the stove conveniently from a distance. The manual control option is also available for those who prefer a more traditional experience.

In terms of safety, the stove comes with built-in safety measures, including a flame failure device that automatically shuts off the gas supply if the flame goes out unexpectedly.

Overall, the Jotul GF 400 DV gas stove represents the perfect blend of traditional craftsmanship and modern efficiency. Its combination of aesthetics, innovative features, and practical heating capabilities makes it an ideal choice for homeowners looking to add warmth and character to their living spaces. Whether you’re enjoying a quiet evening at home or entertaining guests, this stove is sure to impress with its performance and beauty.
Top Page Image Contents