Empire Comfort Systems Empire Heaters Troubleshooting: Optional Blower Installation and Maintenance Instructions

Page 26

OPTIONAL BLOWER INSTALLATION INSTRUCTIONS (continued)

Cleaning

The blower wheel will collect lint and could require cleaning once a year. If the air output decreases or the noise level increases, it indicates a dirty wheel.

Blower Motor

The blower motor does not have oiling holes. Do not attempt to oil blower motor.

Wiring

The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code ANSI/NFPA No. 70, if an external electrical source is utilized. This appliance is equipped with a three-prong [grounding] plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. For an ungrounded receptacle, an adapter, which has two prongs and a wire for grounding, can be purchased, plugged into the ungrounded receptacle and its wire connected to the receptacle mounting screws. With this wire completing the ground, the appliance cord plug can be plugged into the adapter and be electrically grounded.

CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing.

WARNING:

Unplugging of blower accessory will not stop the heater from cycling. To shut heater off: Turn temperature dial or thermostat to lowest setting. Turn knob on gas control to "OFF", depressing slightly. Do not force.

 

 

PARTS LIST

Index

Part

Description

No.

No.

 

1R-1454 Brass Bushing (4 Required)

2R-1499 Rubber Grommet (4 Required)

3CI-002 Blower Housing

4R-1517 Tinnerman Clip (4 Required)

5R-2804-A Blower Assembly

6CI-003 Blower Housing Cover

7

R-2099

Cord Set

8R-3767-A Wire Harness

9A

CI-004

Fan Control Bracket

 

 

(Use with CIBV-30 and CIVF-25)

9B

CI-325

Fan Control Bracket

 

 

(Use with CIDV-30)

10

R-2503

Fan Control

11R-2805 Auto/Off/On Switch

12CI-220 Fan Control Shield (Use with CIVF-25)

13R-1410 Bushing 7/8" Diameter

Page 26

16938-3-0806

Image 26
Contents Installation Instructions Table of Contents Important Safety Information Minimize this effect. The use of this fan will also improveSafety Information for Users of LP-GAS LP-GAS Warning OdorQualified Installing Agency SpecificationsInstructions to Installer IntroductionUnusually Tight Construction Unusually tight construction is defined as construction whereRecommended Gas Pipe Diameter Installing a New Main Gas CockPressure Testing of the Gas Supply System Checking Manifold PressureClearances Figures 2, 3 Installation on Rugs and TileClearances Appliance Hardware Package Parts List Appliance Hardware PackageAssembly of Stove Casting Detailed Instructions Follow16938-3-0806 Assembly of Stove Casting Installation of Optional Stone Inlay Optional Stone Inlay InstallationWire Channel Installation Parts ListInitial Lighting Figure LOG PlacementOperating Guidelines Standing Pilot OperationFor Your Safety Read Before Lighting Lighting InstructionsPilot Flame Characteristics Correct Pilot Flame Pattern Incorrect Pilot Flame PatternMain Burner Flame Characteristics Cleaning the Log Set and FireboxWiring Maintenance Wiring Diagram FigureMain burner does not light after ODS/pilot is lit TroubleshootingDelayed ignition of main burner HOW to Order Repair Parts Parts List for Stove Casting Parts List for CIVF-25-21Parts View for Stove Casting Parts View for CIVF-25-21 Fan Control Optional Blower Installation InstructionsInstalling Optional CIB-2 Blower Blower Motor CleaningWiring Index Part DescriptionService Notes