Petsafe PPA11-10711, PPA11-10709 manual Setting SmartDoor’s Sensitivity Level

Page 10

NOTE: The SmartDoor™ is designed with an electric motor to release and unlock flap when a SmartKey™ is detected. Do not allow your pet to run or charge through the SmartDoor™. Due to variable radio-frequency interferences it could take several seconds for SmartKey™’s unique code to read properly and SmartDoor™’s flap to unlock.

SET

A. Setting SmartDoor™’s Sensitivity Level

It is necessary to set your SmartDoor™’s sensitivity level so your pet’s SmartKey™ works properly due to location or application material, such as radio-frequency interferences, wood or metal door installations.

To begin, it is recommended to use the split ring (included) to attach the SmartKey™ to the D-ring on your pet’s collar. Also do not use metal tags as the additional metal can cause radio-frequency interference and hinder the detection of your pet’s SmartKey™. Now, continue with the following “product in use” steps:

1. Put the dog’s collar on your leg just below your knee. Tape

may be used to secure the collar, if necessary. See A. A. 2. Stand directly in front of the SmartDoor™ so the SmartKey™

is approximately 2.5 feet (76 cm) from the SmartDoor™. 3. Put the SmartDoor™ in the UNLOCKED Mode. (See page 6

for operational instructions).

4. Put the SmartDoor™ in the Sensitivity Test Mode by holding down the MODE-RESET and LEARN buttons at the same time until all three lights flash once.

5. Turn the Sensitivity Knob counter clockwise to the minimum position, then turn the Sensitivity Knob clockwise until all lights begin to flash again.

6.Slowly continue to adjust the Sensitivity Knob clockwise

until you see a minimum of six consecutive flashes and stop adjusting. Do not adjust higher than necessary.

7. Put the SmartDoor™ in AUTOMATIC Mode and step away at least 10 feet (3 m), allowing the door to automatically lock. This may take up to fifteen seconds after the SmartKey™ no longer is detected.

8. Now confirm the sensitivity level by approaching the SmartDoor™ again. The door should unlock when you step within approximately 2 feet (60 cm) in front of the SmartDoor™.

B. Understanding Sensitivity and the Active Area

The Active Area is the area where the SmartDoor™ will consistently open based on your adjustment of the sensitivity level. In the Fringe Area the SmartDoor™ may open inconsistently due to variables of radio-frequency interferences or reflections. In the Inactive Area the door will generally not unlock automatically. See B.

You may see slight differences between Outside and Inside Active Areas due to radio-frequency interferences.

Depending on location and application

~2.5 feet (76 cm)

~6 feet (183 cm)

B.Door - Top View

Outside Inactive

Fringe

Active

Active

Fringe

Inside Inactive

10

1-800-732-2677

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Operating Guide Guide d’emploi Guia para el uso Model Numbers PPA11-10711 Small, PPA11-10709 LargeImportant Safety Information Table of Contents How the SmartDoor Works ComponentsTools Needed Level Tape Pencil StringPrepare Outer Frame Size Overall pet door dimensionsPreparing Your SmartDoor Operational ModesOperational Indicators Place Battery in the SmartKeyCheck Operational Modes Before Installation Place Batteries in the SmartDoorCheck SmartDoor Location Before Installation Installing Your SmartDoorInstall Determine Pet Door LocationCut Pet Door Opening Preparing DoorStep Train Your Pet Install Pet DoorStep Insert Screws Re-hang door and place interior frame withSET Setting SmartDoor’s Sensitivity LevelUnderstanding Sensitivity and the Active Area Attach the SmartKey to the Pet’s Collar OperateProgramming a New SmartKey Operating Your SmartDoorClear SmartKey Memory Replacement Parts and AccessoriesRevert SmartKey to Default Factory Setting Component Part NumberTerms of Use and Limitation of Liability Perchlorate Battery Important Recycling AdviceBattery Disposal ComplianceAustralia Importante information de sécurité Même la mortTable des matières PréparationOutils nécessaires ComposantsComment fonctionne la SmartDoor Définitions clefs Modes de fonctionnementPréparation de votre SmartDoor Installez les piles dans la SmartDoorInstallez a pile dans la SmartKey PréparationVérification lendroit de la SmartDoor avant linstallation Modes de fonctionnementÉtape Déterminez le lieu dinstallation de la chatière Installation de votre SmartDoorInstallation Étape Préparation de la porteCoupez louverture pour la chatière Installation de la chatièrePour la scie sauteuse Réglage Étape Insérez les visÉtape Entraînement de votre animal Réglage du niveau de sensibilité de la SmartDoorCompréhension la sensibilité et de la zone active ~ 76 cm 2,5 pi ~ 183 cm 6 piFixez la SmartKey au collier de votre animal FonctionnementProgrammation dune nouvelle SmartKey Fonctionnement de votre SmartDoorRétablir la SmartKey aux réglages par défaut Pièces de remplacement et accessoiresEffacer la mémoire SmartKey Conditions dutilisation et limitation de responsabilité Service à la clientèle InternationalPile perchlorate Composant Numéro de pièceConformité Avis de recyclage importanteMise au rebut de pile CC/CanadaInformación importante sobre seguridad Tabla de contenido PreparaciónCómo funciona el receptor SmartDoor ComponentesHerramientas necesarias Nivel Cinta Lápiz HiloDefiniciones clave Modos de funcionamientoColoque las pilas en el receptor SmartDoor Prepare el receptor SmartDoorPreparación Coloque la batería en el transmisor SmartKeyModos de funcionamiento Seleccione el lugar donde instalará la puerta InstalaciónCómo instalar el receptor SmartDoor Para mascotasMascotas encaje correctamente Instale la puerta para mascotasCorte el hueco donde se colocará la puerta para mascotas Consejo útil Utilice una sierra con la hojaConfiguración Paso Coloque los tornillosConsulte el punto B Para comprender el área activa y de sensibilidad~ 2,5 pies 76 cm ~ 6 pies 183 cm Cómo funciona el receptor SmartDoor FuncionamientoCómo programar un transmisor SmartKey nuevo Color de la luz SituaciónPiezas y accesorios de repuesto Cómo borrar la memoria del transmisor SmartKeyAtención al Cliente Internacional Componente Número de piezaCumplimiento Pilas de perclorato Aviso importante sobre recicladoEliminación de las pilas Comisión Federal de Comunicaciones/CanadáAustralia Radio Systems Corporation

PPA11-10709, PPA11-10711 specifications

The PetSafe PPA11-10709 and PPA11-10711 are innovative pet training collars designed to enhance the training experience for both dogs and their owners. These products incorporate advanced features and technologies to ensure effective communication between you and your pet.

The PPA11-10709 collar is known for its lightweight design, making it comfortable for dogs of various sizes. It includes a range of training modes, allowing owners to choose the best method for their pet. The adjustable static stimulation levels provide a customizable training experience, enabling users to select the appropriate intensity for their dog's sensitivity. Additionally, this collar boasts a waterproof design, ensuring it continues to function effectively, even in wet conditions.

On the other hand, the PPA11-10711 model emphasizes a more advanced training experience. It offers a combination of audible tones and vibrations, catering to pets that may respond better to these forms of communication rather than solely static stimulation. This model also comes with a longer battery life, ensuring that training sessions can continue uninterrupted. The durable construction makes it suitable for active dogs, providing a reliable solution for both indoor and outdoor training.

Both models incorporate PetSafe’s innovative technology that ensures consistent signal transmission, reducing the chances of miscommunication during training. The collars are compatible with various PetSafe training accessories, allowing users to expand their training toolkit to meet their dog’s unique needs.

Moreover, the easy-to-read instructional manual and user-friendly interface make the setup process simple, allowing even first-time pet owners to get started with training quickly. The ergonomic design also enables owners to adjust the collar comfortably on their pets, ensuring it fits securely without causing discomfort.

In conclusion, the PetSafe PPA11-10709 and PPA11-10711 collars are excellent tools for effective dog training. By integrating customizable training modes, waterproof features, and durable materials, these collars reflect PetSafe's commitment to providing quality products that facilitate positive pet behavior. Whether you’re looking for a straightforward training collar or a more advanced system, these models deliver the functionality and reliability that every pet owner seeks.
Top Page Image Contents