Petsafe PPA11-10709, PPA11-10711 manual Installing Your SmartDoor, Determine Pet Door Location

Page 7

AUTOMATIC MODE – Allows entry and exit for a pet wearing a programmed SmartKey™. To set: hold the MODE-RESET button until the yellow light illuminates and release when selected. Five SmartKeys™ can be programmed to one SmartDoor™ for selective entry and exit during AUTOMATIC MODE.

NOTE: If at any time the red light remains illuminated, replace with a set of fresh batteries. If that does not reset the red light, please call our Customer Care Center for additional help.

If any part of step C was unsuccessful, please call our Customer Care Center for additional help.

D. Check SmartDoor™ Location Before Installation

DO NOT REMOVE SENSITIVITY STICKER BEFORE INSTALLING THE SMARTDOOR™.

Prior to installation, it is recommended to check that the SmartDoor™ will operate properly in the intended location or application to guard against possible severe radio-frequency interference. Household appliances and common electronic products should be located at least two feet (60 cm) away from the SmartDoor™’s location. Radio-frequency interference detected from other household appliances or common electronic products will negatively affect the ability of the SmartDoor™ to receive a SmartKey™ signal. Typical appliances and products to consider are laptop computers, wireless telephones, microwaves, televisions, garage door openers, hand-held electronic devices (such as cell phones, game stations and remote controls).

The sticker placed over the sensitivity knob should not be removed until after installation, as the factory default sensitivity setting is positioned at the optimal level for most installations.

It is recommended to install SmartDoor™ in a location where direct wind is not a factor. Operating Temperature Range: -5˚ F to 180˚ F (-20.5˚ C to 82˚ C). Operating Humidity Range: 0 to 99.9%.

•To check if SmartDoor™’s radio-frequency technology will operate properly in desired location and application, place SmartDoor™ directly in front of and against the door or application in the upright position. After performing steps A-C, now set the SmartDoor™ in AUTOMATIC mode and hold the SmartKey™ directly in front of the SmartDoor™. The SmartDoor™ flap should unlock in about three seconds. Remember, the SmartKey™ included in the kit is already programmed to the SmartDoor™.

NOTE: If there are existing SmartKeys™ in the household, remove all (RFA-67) batteries while performing step D except the SmartKey™ included with the SmartDoor™.

If the SmartDoor™ does not unlock, move the SmartDoor™ to another location and follow steps A-D once more. If the SmartDoor™’s location test above was unsuccessful, please call our Customer Care Center for additional help.

When steps A-D are completed and all are successful, your SmartDoor™ is ready for installation.

INSTALL

 

 

Installing Your SmartDoor™

Step

Determine Pet Door Location

1

1A

 

1A Measure and mark your pet’s shoulder

1B

height on the door.

 

1B Determine location for the pet door. Draw

 

 

 

 

a vertical center line through the shoulder

 

 

height line using a level.

 

 

 

NOTICE

 

 

 

If homeowner’s door or other application is

 

 

 

not level, the pet door must be marked level to

 

 

 

swing properly.

www.petsafe.net

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Model Numbers PPA11-10711 Small, PPA11-10709 Large Operating Guide Guide d’emploi Guia para el usoImportant Safety Information Table of Contents Level Tape Pencil String ComponentsTools Needed How the SmartDoor WorksOperational Modes Outer Frame Size Overall pet door dimensionsPreparing Your SmartDoor PreparePlace Batteries in the SmartDoor Place Battery in the SmartKeyCheck Operational Modes Before Installation Operational IndicatorsDetermine Pet Door Location Installing Your SmartDoorInstall Check SmartDoor Location Before InstallationPreparing Door Cut Pet Door OpeningRe-hang door and place interior frame with Install Pet DoorStep Insert Screws Step Train Your PetSET Setting SmartDoor’s Sensitivity LevelUnderstanding Sensitivity and the Active Area Operating Your SmartDoor OperateProgramming a New SmartKey Attach the SmartKey to the Pet’s CollarComponent Part Number Replacement Parts and AccessoriesRevert SmartKey to Default Factory Setting Clear SmartKey MemoryCompliance Perchlorate Battery Important Recycling AdviceBattery Disposal Terms of Use and Limitation of LiabilityAustralia Même la mort Importante information de sécuritéPréparation Table des matièresOutils nécessaires ComposantsComment fonctionne la SmartDoor Modes de fonctionnement Définitions clefsPréparation Installez les piles dans la SmartDoorInstallez a pile dans la SmartKey Préparation de votre SmartDoorModes de fonctionnement Vérification lendroit de la SmartDoor avant linstallationÉtape Préparation de la porte Installation de votre SmartDoorInstallation Étape Déterminez le lieu dinstallation de la chatièreCoupez louverture pour la chatière Installation de la chatièrePour la scie sauteuse Réglage du niveau de sensibilité de la SmartDoor Étape Insérez les visÉtape Entraînement de votre animal Réglage~ 76 cm 2,5 pi ~ 183 cm 6 pi Compréhension la sensibilité et de la zone activeFonctionnement de votre SmartDoor FonctionnementProgrammation dune nouvelle SmartKey Fixez la SmartKey au collier de votre animalRétablir la SmartKey aux réglages par défaut Pièces de remplacement et accessoiresEffacer la mémoire SmartKey Composant Numéro de pièce Service à la clientèle InternationalPile perchlorate Conditions dutilisation et limitation de responsabilitéCC/Canada Avis de recyclage importanteMise au rebut de pile ConformitéInformación importante sobre seguridad Preparación Tabla de contenidoNivel Cinta Lápiz Hilo ComponentesHerramientas necesarias Cómo funciona el receptor SmartDoorModos de funcionamiento Definiciones claveColoque la batería en el transmisor SmartKey Prepare el receptor SmartDoorPreparación Coloque las pilas en el receptor SmartDoorModos de funcionamiento Para mascotas InstalaciónCómo instalar el receptor SmartDoor Seleccione el lugar donde instalará la puertaConsejo útil Utilice una sierra con la hoja Instale la puerta para mascotasCorte el hueco donde se colocará la puerta para mascotas Mascotas encaje correctamentePaso Coloque los tornillos ConfiguraciónConsulte el punto B Para comprender el área activa y de sensibilidad~ 2,5 pies 76 cm ~ 6 pies 183 cm Color de la luz Situación FuncionamientoCómo programar un transmisor SmartKey nuevo Cómo funciona el receptor SmartDoorCómo borrar la memoria del transmisor SmartKey Piezas y accesorios de repuestoComponente Número de pieza Atención al Cliente InternacionalComisión Federal de Comunicaciones/Canadá Pilas de perclorato Aviso importante sobre recicladoEliminación de las pilas CumplimientoAustralia Radio Systems Corporation

PPA11-10709, PPA11-10711 specifications

The PetSafe PPA11-10709 and PPA11-10711 are innovative pet training collars designed to enhance the training experience for both dogs and their owners. These products incorporate advanced features and technologies to ensure effective communication between you and your pet.

The PPA11-10709 collar is known for its lightweight design, making it comfortable for dogs of various sizes. It includes a range of training modes, allowing owners to choose the best method for their pet. The adjustable static stimulation levels provide a customizable training experience, enabling users to select the appropriate intensity for their dog's sensitivity. Additionally, this collar boasts a waterproof design, ensuring it continues to function effectively, even in wet conditions.

On the other hand, the PPA11-10711 model emphasizes a more advanced training experience. It offers a combination of audible tones and vibrations, catering to pets that may respond better to these forms of communication rather than solely static stimulation. This model also comes with a longer battery life, ensuring that training sessions can continue uninterrupted. The durable construction makes it suitable for active dogs, providing a reliable solution for both indoor and outdoor training.

Both models incorporate PetSafe’s innovative technology that ensures consistent signal transmission, reducing the chances of miscommunication during training. The collars are compatible with various PetSafe training accessories, allowing users to expand their training toolkit to meet their dog’s unique needs.

Moreover, the easy-to-read instructional manual and user-friendly interface make the setup process simple, allowing even first-time pet owners to get started with training quickly. The ergonomic design also enables owners to adjust the collar comfortably on their pets, ensuring it fits securely without causing discomfort.

In conclusion, the PetSafe PPA11-10709 and PPA11-10711 collars are excellent tools for effective dog training. By integrating customizable training modes, waterproof features, and durable materials, these collars reflect PetSafe's commitment to providing quality products that facilitate positive pet behavior. Whether you’re looking for a straightforward training collar or a more advanced system, these models deliver the functionality and reliability that every pet owner seeks.
Top Page Image Contents