Petsafe PPA11-10711 Replacement Parts and Accessories, Revert SmartKey to Default Factory Setting

Page 12

Yellow light is flashing

• Obstruction to the flap has been detected.

 

• Press the MODE-RESET button to cause the SmartDoor™ to attempt

 

to lock the flap. Clear any obstructions that keep the flap from

 

locking. When the flap successfully locks, normal operation is resumed.

 

• If your large SmartDoor™ does not close properly, you can purchase

 

an additional magnet kit to help center flap due to constant wind

 

or a variance between indoor and outdoor pressure. Please call the

 

Customer Care Center for further assistance.

Red light remains

• Remove batteries and replace them with a fresh set of batteries. If

illuminated (internal

that does not reset the red light, please call Customer Care Center at

failure has occurred)

1-800-732-2677 for additional help.

Red light is flashing

• Low battery indicator, replace batteries.

Red, green and yellow

• Sensitivity set mode has been activated. It will automatically

lights are flashing

de-activate in thirty minutes, or can be immediately de-activated by

 

pressing the MODE-RESET button once.

Revert SmartKey™ to Default Factory Setting

The SmartDoor™ can be cleared of all additional programmed SmartKey™ EXCEPT the one included from the factory. To do this, first take out batteries from battery compartment. Then, as you place batteries back into the battery compartment, hold down the LEARN button. When LEARN button is held and the last battery is in place, the red and green lights will illuminate three times. Now, all SmartKeys™ programmed to the SmartDoor™ have been cleared except the one SmartKey™ included with your SmartDoor™.

Clear SmartKey™ Memory

The SmartDoor™ can be cleared of all programmed SmartKeys™, even the one included from the factory. To do this, first remove batteries from battery compartment. Then, as you place batter- ies back into the battery compartment, hold down the MODE-RESET button. When MODE-RESET button is held and the last battery is in place, the red and yellow lights will illuminate three times. Now all SmartKeys™ have been cleared.

______________________________________________________________________________

Replacement Parts and Accessories

To purchase replacement parts for your PetSafe® SmartDoor™, contact the Customer Care Center at 1-800-732-2677or visit our website at www.petsafe.net to locate a retailer near you.

Customer Care International

Canada: 1-800-732-2677

Australia: 1800 786 608

United Kingdom: 0800 046 1414

New Zealand: 0800 543 054

Europe: 00 800 18 18 20 20

 

 

 

 

 

Component

 

Part Number

SmartKey™

 

PAC11-11405

PetSafe® RFA-67 Battery

 

RFA-67

Small Replacement Flap

 

CPA11-11580/MPA00-12830

Large Replacement Flap

 

CPA11-11579/MPA00-12829

Small SmartDoor™ Hardware Kit

 

CPA00-11617/MPA00-12814

Large SmartDoor™ Hardware Kit

 

CPA00-11618/MPA00-12815

Small Wall Conversion Kit

 

MPA11-12019

Large Wall Conversion Kit

 

MPA11-12020

Large Extension Tunnel

 

CPA00-12021/MPA00-12820

Small Wall Conversion – Hardware Replacement Kit

CPA00-12054/MPA00-12821

Large Wall Conversion – Hardware Replacement Kit

CPA00-12055/MPA00-12822

12

1-800-732-2677

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Operating Guide Guide d’emploi Guia para el uso Model Numbers PPA11-10711 Small, PPA11-10709 LargeImportant Safety Information Table of Contents Components Tools NeededHow the SmartDoor Works Level Tape Pencil StringOuter Frame Size Overall pet door dimensions Preparing Your SmartDoorPrepare Operational ModesPlace Battery in the SmartKey Check Operational Modes Before InstallationOperational Indicators Place Batteries in the SmartDoorInstalling Your SmartDoor InstallCheck SmartDoor Location Before Installation Determine Pet Door LocationCut Pet Door Opening Preparing DoorInstall Pet Door Step Insert ScrewsStep Train Your Pet Re-hang door and place interior frame withSetting SmartDoor’s Sensitivity Level SETUnderstanding Sensitivity and the Active Area Operate Programming a New SmartKeyAttach the SmartKey to the Pet’s Collar Operating Your SmartDoorReplacement Parts and Accessories Revert SmartKey to Default Factory SettingClear SmartKey Memory Component Part NumberPerchlorate Battery Important Recycling Advice Battery DisposalTerms of Use and Limitation of Liability ComplianceAustralia Importante information de sécurité Même la mortTable des matières PréparationComposants Outils nécessairesComment fonctionne la SmartDoor Définitions clefs Modes de fonctionnementInstallez les piles dans la SmartDoor Installez a pile dans la SmartKeyPréparation de votre SmartDoor PréparationVérification lendroit de la SmartDoor avant linstallation Modes de fonctionnementInstallation de votre SmartDoor InstallationÉtape Déterminez le lieu dinstallation de la chatière Étape Préparation de la porteInstallation de la chatière Coupez louverture pour la chatièrePour la scie sauteuse Étape Insérez les vis Étape Entraînement de votre animalRéglage Réglage du niveau de sensibilité de la SmartDoorCompréhension la sensibilité et de la zone active ~ 76 cm 2,5 pi ~ 183 cm 6 piFonctionnement Programmation dune nouvelle SmartKeyFixez la SmartKey au collier de votre animal Fonctionnement de votre SmartDoorPièces de remplacement et accessoires Rétablir la SmartKey aux réglages par défautEffacer la mémoire SmartKey Service à la clientèle International Pile perchlorateConditions dutilisation et limitation de responsabilité Composant Numéro de pièceAvis de recyclage importante Mise au rebut de pileConformité CC/CanadaInformación importante sobre seguridad Tabla de contenido PreparaciónComponentes Herramientas necesariasCómo funciona el receptor SmartDoor Nivel Cinta Lápiz HiloDefiniciones clave Modos de funcionamientoPrepare el receptor SmartDoor PreparaciónColoque las pilas en el receptor SmartDoor Coloque la batería en el transmisor SmartKeyModos de funcionamiento Instalación Cómo instalar el receptor SmartDoorSeleccione el lugar donde instalará la puerta Para mascotasInstale la puerta para mascotas Corte el hueco donde se colocará la puerta para mascotasMascotas encaje correctamente Consejo útil Utilice una sierra con la hojaConfiguración Paso Coloque los tornillosPara comprender el área activa y de sensibilidad Consulte el punto B~ 2,5 pies 76 cm ~ 6 pies 183 cm Funcionamiento Cómo programar un transmisor SmartKey nuevoCómo funciona el receptor SmartDoor Color de la luz SituaciónPiezas y accesorios de repuesto Cómo borrar la memoria del transmisor SmartKeyAtención al Cliente Internacional Componente Número de piezaPilas de perclorato Aviso importante sobre reciclado Eliminación de las pilasCumplimiento Comisión Federal de Comunicaciones/CanadáAustralia Radio Systems Corporation

PPA11-10709, PPA11-10711 specifications

The PetSafe PPA11-10709 and PPA11-10711 are innovative pet training collars designed to enhance the training experience for both dogs and their owners. These products incorporate advanced features and technologies to ensure effective communication between you and your pet.

The PPA11-10709 collar is known for its lightweight design, making it comfortable for dogs of various sizes. It includes a range of training modes, allowing owners to choose the best method for their pet. The adjustable static stimulation levels provide a customizable training experience, enabling users to select the appropriate intensity for their dog's sensitivity. Additionally, this collar boasts a waterproof design, ensuring it continues to function effectively, even in wet conditions.

On the other hand, the PPA11-10711 model emphasizes a more advanced training experience. It offers a combination of audible tones and vibrations, catering to pets that may respond better to these forms of communication rather than solely static stimulation. This model also comes with a longer battery life, ensuring that training sessions can continue uninterrupted. The durable construction makes it suitable for active dogs, providing a reliable solution for both indoor and outdoor training.

Both models incorporate PetSafe’s innovative technology that ensures consistent signal transmission, reducing the chances of miscommunication during training. The collars are compatible with various PetSafe training accessories, allowing users to expand their training toolkit to meet their dog’s unique needs.

Moreover, the easy-to-read instructional manual and user-friendly interface make the setup process simple, allowing even first-time pet owners to get started with training quickly. The ergonomic design also enables owners to adjust the collar comfortably on their pets, ensuring it fits securely without causing discomfort.

In conclusion, the PetSafe PPA11-10709 and PPA11-10711 collars are excellent tools for effective dog training. By integrating customizable training modes, waterproof features, and durable materials, these collars reflect PetSafe's commitment to providing quality products that facilitate positive pet behavior. Whether you’re looking for a straightforward training collar or a more advanced system, these models deliver the functionality and reliability that every pet owner seeks.
Top Page Image Contents