Trane PTAC-SVX01C-EN manual Display units, Setpoint limiting, SI Metric

Page 18

Installation

1.Ventilation Door Function

The power door works based upon control logic functions. When the unit is on, the vent door will open to allow fresh air to be conditioned before entering the room. When the unit is off, the door closes to prevent unconditioned air from entering the room.

For more information on vent door function with dehumidificaiton, refer to the dehumidification chart.

2.Indoor Fan Cycle set up

The indoor fan can be configured to provide different types of operation between its OFF and ON (high/low) states. This setting is adjustable and does not force the unit to reset.

3.Temperature Setpoint Limiting set up

The range of temperature control setpoints can be limited using this configuration parameter. After the controller has determined the desired user setpoint from the display, the resulting value is validated against the setpoint limits. There are four valid combinations of heating and cooling setpoint limits:

These set point limits apply to both the occupied and unoccupied standby, heating and cooling setpoints. This setting is adjustable “on-the-fly” and will not force the unit into a restart condition.

4.Energy Management Setpoint Offset set up

The range of the Energy Management System's effect on setpoints can be adjusted using this configuration parameter. This parameter is adjustable "on-the-fly" and will not force the controller into a restart condition. The range and resolution of available selections is

Range: 0°F to 20°F( 0.0°C to 11.0°C)

Resolution: 1.0°F( 0.5°C)

5.Display Unit set up

The user can change the way the interface module displays temperature. The symbols °F and °C will not be present on the display; however, the range and precision of the room temperature and setpoint values will make the selection obvious.

6.Indoor temperature calibration

The indoor temperature can be calibrated to match an independent reading. The adjustment range is +/- 10.0°F (6°C) with a resolution of 1°F (0.5°C).

7.Dehumidification Offset

The offset defines the point below the setpoint where the unit will stop running the compressor. A DH display module is required to use this feature.

The PTAC allows the options of 0°F (disable), 1°F (default) and 2°F (optional) for the dehumidification offset. The dehumidification feature will be disabled when the configuration of 0°F is selected.

Last User Setpoint, Mode, and

Fan Selections

The controller saves the last inputs that the user has chosen 5 seconds after the user has ceased changing them. These settings will be used after the next power cycle or controller reset.

Operation without configuration

The controller tests the configuration for validity. If the data is corrupted the controller will revert to default values for every parameter. A diagnostic code will be displayed when using the default values.

Table 10.

Display units

 

 

 

 

Selection

Unit of

Display

#

Measure

Example

 

 

 

0

IP (English)

77 (DEFAULT)

 

 

 

1

SI (Metric)

24.5

 

 

 

Table 11.

Setpoint limiting

 

 

 

 

 

 

 

 

 

 

Cooling Setpoint

Heating Setpoint

 

 

 

 

 

 

Selection

 

 

High

Low

 

#

 

Low Limit

Limit

Limit

High Limit

 

 

 

 

 

 

0

 

50°F

90°F

50°F

90°F (DEFAULT)

 

 

 

 

 

 

1

 

55°F

90°F

50°F

85°F

 

 

 

 

 

 

2

 

60°F

90°F

50°F

80°F

 

 

 

 

 

 

3

 

65°F

90°F

50°F

75°F

 

 

 

 

 

 

18

PTAC-SVX01C-EN

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Packaged Terminal Air Conditioner Table of Contents Model Number Description E E 0 9 0 1 * a aOverview of Manual General InformationImportant Environmental Concerns Responsible Refrigerant PracticesGeneral Information Checklist Pre-InstallationPre-Installation Considerations Fire HazardReceiving and Handling Pre-InstallationReceiving Checklist Shipping PackageUnit Dimensions Unit with wall sleeve and subbase accessory Wall SleeveUnit Dimensions Air dischargeInstallation Live Electrical ComponentsElectrical Requirements Installation Power receptacle configurationsHazardous Voltage w Installation ProcedureRemove rear closure Panel from wall sleeveInstall unit power supply BottomOption Install the unit controlsVoltage Options Accessory Accessory part number 115V 265 OptionSpecification Wiring VoltageWire External Interface Size LengthConfigure the display module settings Output settingsField commissioning support Programmable Settings Set point configurationSelection Unit Display Measure Example IP English Display unitsSetpoint limiting SI MetricIndoor fan cycle configuration Energy Management SystemOccupancy arbitration for energy management Off 10 sec Ptee manual test sequencePthe manual test sequence Off 20 secOperation Sequence of OperationVent Control OperationRemote Fan Operation Air Discharge GrilleAir conditioner performance data Electric heat Data Heater size Heat pump performanceVoltage 208 230 265 Cooling data Btu/HCooling temperature change heat pumps Cooling temperature change air conditionersCooling amperage air conditioners Cooling amperage heat pumpsHeating total wattage input heat pumps Voltage 208 230 265Heating Btu/H Unit accessory model numbers Hydronic heat options Maintenance Maintenance ProceduresMaintenance Refrigeration System ServiceHigh Temperatures Maintenance BrazingLeak Testing Use of Pressure Regulator Valves GaugesMaintenance Evacuation Evacuation ProcedureFan Motor Overheat Refrigerant Charging ProcedureCharging the System Line Piercing ValvesSling Psychrometer Maintenance Cooling Performance TestThermometers Cooling Performance TestTesting Capacitor Resistance Heating Power Consumption TestCalculating procedure Resistance CheckResistance Test Heater Assembly with Power OFF to the Unit and HeaterGround Test Indoor Coil and Air ThermistorsThermistor indoor coil Resistance Rmin Rnom RmaxUnit Disassembly Procedures Power Cord RemovalComponent Replacement Power cord InstallationIndoor Fan and Motor Control Board Replacement Procedure Hazardous VoltageRemoving the Outdoor Coil and Outdoor Air Thermistors Outdoor Fan and MotorTroubleshooting DiagnosticsIndoor/remote fan outputs do not energize TroubleshootingCompressor output does not energize Outdoor fan output does not energizeAuxiliary heat output does not energize Random restart timer ExplanationReversing valve output does not energize Ventilation output does not energizeCondensate pump does not energize Output on when the mode is offSymptom Control fuse is blownWiring Diagram AIR CoilWiring Diagram PVDWiring diagram 07 models PVD Energy management system Full 2nd 5th Sealed System Warranty WarrantyFull 1st Year Warranty Limited 2nd through 5th Year Functional Parts WarrantyPage PTAC-SVX01C-EN

PTAC-SVX01C-EN specifications

The Trane PTAC-SVX01C-EN is a cutting-edge Packaged Terminal Air Conditioner (PTAC) designed to provide optimal temperature control, energy efficiency, and user comfort in a variety of settings, including hotels, apartments, and office buildings. This unit stands out with its robust features and advanced technologies, making it a reliable choice for meeting diverse heating and cooling needs.

At the heart of the Trane PTAC-SVX01C-EN is its innovative design, which combines powerful performance with quiet operation. This unit utilizes a high-efficiency compressor that ensures rapid cooling and heating, providing ideal comfort regardless of the external climate. With a capacity range suitable for smaller spaces, the PTAC delivers strong performance while maintaining energy efficiency, thus reducing operational costs over time.

One of the key characteristics of the PTAC-SVX01C-EN is its user-friendly interface. The intuitive controls allow users to effortlessly adjust temperature settings, fan speeds, and modes of operation, including cooling, heating, and fan only. This flexibility enhances user comfort while optimizing energy consumption. Additionally, the unit features a programmable timer, enabling users to schedule operation according to their specific needs, further conserving energy when spaces are unoccupied.

The unit's Quiet Operation Technology minimizes noise levels, making it an ideal choice for environments where peace and quiet are paramount. This feature is particularly beneficial in hospitality settings, where guests expect a tranquil atmosphere. The PTAC is engineered to provide ample airflow while minimizing sound, creating a pleasant indoor environment.

Another standout feature of the Trane PTAC-SVX01C-EN is its advanced air filtration system. The integrated filter effectively captures dust, allergens, and other airborne particles, promoting a cleaner and healthier living environment. This is particularly essential for individuals with allergy sensitivities or respiratory issues.

Durability is also a hallmark of the PTAC-SVX01C-EN. Built with high-quality materials, it is designed to withstand the demands of continuous operation while requiring minimal maintenance. The unit's sleek and compact design allows for easy installation in various locations, ensuring versatility without sacrificing performance.

In summary, the Trane PTAC-SVX01C-EN represents a perfect blend of efficiency, comfort, and innovative technology. Its user-friendly controls, quiet operation, and advanced air filtration make it a leading choice for those seeking reliable climate control solutions in residential and commercial spaces alike. Whether for heating or cooling, the Trane PTAC-SVX01C-EN is engineered to deliver exceptional performance and lasting dependability.
Top Page Image Contents