Arming the System (cont’d)
Arming Commands
Before arming, close all perimeter doors and windows and make sure the Ready to Arm message is displayed.
Mode | Press these keys… |
|
|
| Keypad Confirms By… | ||||||
|
|
|
|
|
|
|
|
|
|
| • three beeps† |
STAY | security code + | 3 | STAY |
|
|
|
|
| |||
|
|
|
|
|
| • armed STAY message displayed | |||||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| • red ARMED indicator lights |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| • three beeps† |
NIGHT- | security code + | 3 | STAY | + |
| 3 | STAY | ||||
|
| • | |||||||||
STAY |
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| • red ARMED indicator lights | |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| • three beeps† |
INSTANT | security code + | 7 INSTANT |
|
|
| ||||||
|
|
|
| • armed STAY message displayed | |||||||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| • red ARMED indicator lights |
|
|
|
|
|
|
|
|
|
|
| Note that entry delay is turned off. |
|
|
|
|
|
|
|
|
|
|
| two beeps†, or, if programmed, beeping for |
AWAY | security code + | 2 | AWAY |
|
|
|
| ||||
|
|
|
| duration of exit delay | |||||||
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
| • armed AWAY message displayed |
|
|
|
|
|
|
|
|
|
|
| • red ARMED indicator lights |
|
|
|
|
|
|
|
|
|
|
| Leave the premises through an entry/exit |
|
|
|
|
|
|
|
|
|
|
| door during the exit delay period to avoid |
|
|
|
|
|
|
|
|
|
|
| causing an alarm. The keypad beeps |
|
|
|
|
|
|
|
|
|
|
| rapidly during the last 10 seconds of the |
|
|
|
|
|
|
|
|
|
|
| exit delay to warn you that it is ending. |
|
|
|
|
|
|
|
|
|
|
| • same as AWAY (described above) |
MAXIMUM | security code + | 4 | MAX |
|
|
|
|
|
| ||
|
|
|
| Note that entry delay is turned off. | |||||||
|
|
|
|
|
|
|
|
|
|
|
†Arming Ding: In addition to the keypad beeps, the external sounder emits a short “ding” sound after arming, if programmed to do so. The ding confirms that the system is armed, and may occur immediately after the command or be delayed (until arm/disarm report is sent or exit delay expires). Ask your installer about how this feature is set for your system.
Quick Arming
If "Quick Arming" was programmed by the installer, the [#] key can be pressed in place of the security code when arming the system in any of the arming modes (except Night- Stay). However, the security code must always be used when manually disarming the system.
Function Key Arming
For any arming command, a function key may have also been programmed for your system. If so, you can press and hold the appropriate function key for 2 seconds to arm the system. See your installer for the designated functions (see Single Button Arming section).
Refer to the Accessing Other Partitions section for information on
– 18 –