Honeywell VISTA-21IPSIA manual Scheduling cont’d

Page 38

Scheduling (cont’d)

5.For event number “02,” enter the access group

number. Otherwise, this prompt is skipped. Press [∗] to continue to the “Start” prompt below.

6.For event numbers “03-07,” enter the partition number to be armed or disarmed.

0 = arm all; 1 = partition 1; 2 = partition 2; 3 = arm common

Otherwise, this prompt is skipped.

Press [∗] to continue to the “Start” prompt.

7.Enter the event’s start time and days of week. Hour = 00-12; minute = 00-59

AM = 0; PM = 1

Days = Position the cursor under the desired days using the [∗] key to move forward, then press “1” to

select the day. Press [∗] to continue.

8.If applicable, enter the event’s stop time and days of week (applies only to event numbers 01, 02, and 03).

Refer to step 7 for available entries. Press [∗] to continue.

9.Enter the desired repeat option.

0 = no repeat

1 = repeat schedule weekly

2 = repeat schedule biweekly (every other week)

3 = repeat schedule every third week

4 = repeat schedule every fourth week

e.g., To make a schedule that happens everyday you would select all days with a repeat count of 1. To make a schedule that runs for one week then stops, select everyday with a repeat count of 0.

10.For event number 01 (output on/off), select the randomize option, if desired.

0 = no; 1 = yes

If selected, the schedule times will vary within 60 minutes of the “hour” time. For example, if a schedule is set to start at 6:15pm, it will do so the first time 6:15pm arrives, but on subsequent days it

will start anytime between 6:00 and 6:59 p.m. Press [∗] to continue.

GROUP NUMBER

X

PARTITION

X

START SMTWTFS HH:MMAM 1000000

STOP SMTWTFS HH:MMAM 1000000

REPEAT OPTION

0-4X

RANDOMIZE 0=NO 1=YES X

– 38 –

Image 38
Contents Ademco Vista Series About This Manual Table of Contents Table of Contents System Basics System OverviewIntroduction System Overview cont’d Function Keys Using the Voice Message Center if Voice Keypad is installedPaging Feature SchedulingAbout The Keypads General InformationAbout The Keypads cont’d Armed Ready Message MICFIXED-WORD Display Keypad Functions of the Keypads Armed Ready Message MICFunctions of the Keypads cont’d MIC Exit Delay Entry/Exit DelaysEntry Delay Exit Error Conditions Entry/Exit Delays cont’dExit Alarms Checking For Open Zones Using the ∗ Key to Display and Announce System StatusTo turn the Voice Status feature on/off # Maximum Mode Arms Entire System, Entry Delay Off Instant Mode Arms Perimeter Only, Entry Delay OffAway Mode Arms Entire System, Entry Delay On Arming the SystemArming the System cont’d Arming CommandsMode Press these keys… Keypad Confirms By… Quick ArmingKey First Press Second Press Third Press Single Button ArmingSingle Button Step Arming To arm in the Away mode KeyswitchUsing the Keyswitch To arm in the Stay modeDisarming and Silencing Alarms Using the OFF keyUsing the Bypass Key Bypassing Protection ZonesBypassing Protection Zones cont’d Quick BypassUsing the Voice Chime Chime ModeUsing the Chime Mode Viewing the Current Date and Time Setting the Date and TimeDate and Time Panic Keys Using Panic KeysThis Function Sends This Signal With This Sounding… To activate a Panic FunctionMacro Key Programming & Usage About Macro KeysExample of Macro Programming Using a Programmed Macro KeyMacro Key Programming & Usage cont’d To Activate Devices Using Device CommandsAbout Device Commands To Deactivate DevicesPaging Feature About Automatic PagingLatch Key Paging Paging Feature cont’dAbout Manual Paging Authority Level Definitions Security Codes & Authority LevelsAbout Security Codes How to Assign Security Codes and Attributes Security Codes & Authority Levels cont’dGoto Command and Multi-Partition Arming Accessing Other PartitionsAbout Accessing Partitions Multi-Partition Arming Accessing Other Partitions cont’dUsing the GoTo Command Common Zone Operation Scheduling About SchedulingScheduling cont’d Viewing the Event Log Event Logging ProceduresAbout Event Logging Understanding the Type of Event DisplayedEvent Logging Procedures cont’d STAY/INSTANTTesting the System About Testing the SystemIf there are wireless sensors* in your system, the Check Trouble ConditionsRcvr Jam Alarm 1xx Fault 1xx CheckTrouble Conditions cont’d Or CheckLong Rng Trbl Or no ACBusy-Standby Maintaining Your System Fire Alarm System This Section Applies only to Residential SystemsOr Key Pairs Fire Alarm System cont’dIndividual Keys Kitchen Dining Emergency Evacuation Function Procedure Comments Quick Guide to Basic System FunctionsSummary of Audible/Visual Notifications Fixed-Word Display KeypadsSummary of A/V Notifications cont’d Alpha Display KeypadsIndustry Canada Regulatory Statements and WarningsFCC Part Industrie Canada Regulatory Statements cont’dRinger Equivalence Number Notice System Features Log System Features Log cont’d User SetupUser Setup cont’d Paging SetupList of Output Devices OWNER’S Insurance Premium Credit Request Cont Page Page Limitations of this System ÊK14490V1Š