Honeywell VISTA-21IPSIA manual About Testing the System

Page 41

Testing the System

About Testing the System

Using the Test mode allows each protection point to be checked for proper operation. Testing should be conducted weekly to ensure proper operation.

The keypad sounds a single beep about every 30 seconds as a reminder that the system is in the Test mode.

Alarm messages are not sent to your Central Station while Test mode is on.

1.Disarm the system and close all protected windows, doors, etc. The READY indicator light should come on if all zones are intact (i.e., all protected windows, doors, etc. are closed.

2. + 5 TEST then [0] (walk)

(Master Code)

Alpha Displays:

∗∗∗∗DISARMED∗∗∗∗

READY TO ARM

1 = DIAL, 0 = WALK

The Dial test (option “1”) is intended for the installer and should not be used unless directed to do so by your Security System Representative.

3.Listen. The external sounder should sound for about 1 second then turn off. If the sounder does not sound, CALL FOR SERVICE. The “Test in Progress” display appears only on the keypad that started the test.

TEST IN PROGRESS

4.Fault zones. Open each protected door and window in turn and listen for three beeps from the keypad. Identification (zone number or zone description) of each faulted protection point should appear on the display. The display clears when the door or window is closed.

5.Walk in front of any interior motion detectors (if used) and listen for three beeps. The identification of the detector should appear on the display when it is activated. The display clears when no motion is detected. Note that if wireless motion detectors are used, there is a 3-minute delay between activations. This conserves battery life.

6.Test all smoke detectors, following the manufacturer's instructions. The identification of each detector should appear on the display when each is activated. If a problem is experienced with any protection point (no confirming sounds, no display), call for service immediately.

When all protection points have been checked and are intact (closed), there should be no zone identification numbers displayed on the keypad.

7. Exit test mode:

+

(Security Code)

1OFF

If the test mode is inadvertently left active, it automatically turns off after 4 hours. During the final five minutes, the keypad will emit a double beep every 30 seconds.

– 41 –

Image 41
Contents Ademco Vista Series About This Manual Table of Contents Table of Contents System Basics System OverviewIntroduction System Overview cont’d Paging Feature Using the Voice Message Center if Voice Keypad is installedFunction Keys SchedulingGeneral Information About The KeypadsArmed Ready Message MIC About The Keypads cont’dFIXED-WORD Display Keypad Armed Ready Message MIC Functions of the KeypadsFunctions of the Keypads cont’d MIC Exit Delay Entry/Exit DelaysEntry Delay Exit Error Conditions Entry/Exit Delays cont’dExit Alarms Checking For Open Zones Using the ∗ Key to Display and Announce System StatusTo turn the Voice Status feature on/off # Away Mode Arms Entire System, Entry Delay On Instant Mode Arms Perimeter Only, Entry Delay OffMaximum Mode Arms Entire System, Entry Delay Off Arming the SystemMode Press these keys… Keypad Confirms By… Arming CommandsArming the System cont’d Quick ArmingKey First Press Second Press Third Press Single Button ArmingSingle Button Step Arming Using the Keyswitch KeyswitchTo arm in the Away mode To arm in the Stay modeUsing the OFF key Disarming and Silencing AlarmsBypassing Protection Zones Using the Bypass KeyQuick Bypass Bypassing Protection Zones cont’dUsing the Voice Chime Chime ModeUsing the Chime Mode Viewing the Current Date and Time Setting the Date and TimeDate and Time This Function Sends This Signal With This Sounding… Using Panic KeysPanic Keys To activate a Panic FunctionAbout Macro Keys Macro Key Programming & UsageExample of Macro Programming Using a Programmed Macro KeyMacro Key Programming & Usage cont’d About Device Commands Using Device CommandsTo Activate Devices To Deactivate DevicesAbout Automatic Paging Paging FeatureLatch Key Paging Paging Feature cont’dAbout Manual Paging Authority Level Definitions Security Codes & Authority LevelsAbout Security Codes Security Codes & Authority Levels cont’d How to Assign Security Codes and AttributesGoto Command and Multi-Partition Arming Accessing Other PartitionsAbout Accessing Partitions Multi-Partition Arming Accessing Other Partitions cont’dUsing the GoTo Command Common Zone Operation About Scheduling SchedulingScheduling cont’d About Event Logging Event Logging ProceduresViewing the Event Log Understanding the Type of Event DisplayedSTAY/INSTANT Event Logging Procedures cont’dAbout Testing the System Testing the SystemTrouble Conditions If there are wireless sensors* in your system, the CheckTrouble Conditions cont’d Alarm 1xx Fault 1xx CheckRcvr Jam Or CheckLong Rng Trbl Or no ACBusy-Standby Maintaining Your System This Section Applies only to Residential Systems Fire Alarm SystemOr Key Pairs Fire Alarm System cont’dIndividual Keys Kitchen Dining Emergency Evacuation Quick Guide to Basic System Functions Function Procedure CommentsFixed-Word Display Keypads Summary of Audible/Visual NotificationsAlpha Display Keypads Summary of A/V Notifications cont’dIndustry Canada Regulatory Statements and WarningsFCC Part Industrie Canada Regulatory Statements cont’dRinger Equivalence Number Notice System Features Log User Setup System Features Log cont’dPaging Setup User Setup cont’dList of Output Devices OWNER’S Insurance Premium Credit Request Cont Page Page Limitations of this System ÊK14490V1Š