Honeywell VISTA-21IPSIA manual Maintaining Your System

Page 45

Maintaining Your System

Taking Care of Your System

Silencing Low

Battery Warning

Tones at the

Keypad

Replacing

Batteries in

Wireless Sensors

Wireless sensors may not have been used in your security system

IMPORTANT:

Use only batteries recommended by your installer as replacement.

The components of your security system are designed to be as maintenance-free as possible. However, to make sure that your system is in reliable working condition, do the following:

1.Test your system weekly.

2.Test your system after any alarm occurs.

You can silence the keypad’s warning tones by pressing the OFF key, but the keypad's low battery message display will remain on as a reminder that you have a low battery condition in one or more of your wireless sensors. When you replace the weak battery with a fresh one, the sensor sends a "good battery" signal to the control as soon as the sensor is activated (opening/closing of door, window, etc.), causing the low battery display to turn off. If the sensor is not activated, the display will automatically clear within approximately 1 hour.

Each wireless sensor in your system has a 9-volt or 3-volt battery. The system detects a low battery in wireless sensors, including smoke detectors, the personal emergency transmitter, and the portable wireless keypad and displays a low battery message*. (A low battery in a portable wireless keypad is detected as soon as one of its keys is pressed, and displayed as 00.). Battery-operated smoke detectors with a low battery also emit a single "chirp" sound approximately once every 20–30 seconds.

Alkaline batteries provide a minimum of 1 year of operation, and in most units and applications, provide 2–4 years of service. 3-volt lithium batteries provide up to 4 or more years of operation. Actual battery life will depend on the environment in which the sensor is used, the number of signals that the transmitter in the sensor has had to send, and the specific type of sensor. Factors such as humidity, high or low temperatures or large swings in temperature, may all lead to the reduction of actual battery life in an installation.

*The low battery message comes on as a warning that battery replacement in indicated sensor(s) is due within 30 days. In the meantime, a sensor causing a low battery indication is still fully operational.

Routine Care Treat the components of your security system as you would any other electrical equipment. Do not slam sensor-protected doors or windows.

Keep dust from accumulating on the keypad and all protective sensors, particularly on motion sensors and smoke detectors.

The keypad and sensors should be cleaned carefully with a dry soft cloth. Do not spray water or any other fluid on the units.

– 45 –

Image 45
Contents Ademco Vista Series About This Manual Table of Contents Table of Contents System Overview IntroductionSystem Basics System Overview cont’d Paging Feature Using the Voice Message Center if Voice Keypad is installedFunction Keys SchedulingGeneral Information About The KeypadsArmed Ready Message MIC About The Keypads cont’dFIXED-WORD Display Keypad Armed Ready Message MIC Functions of the KeypadsFunctions of the Keypads cont’d MIC Entry/Exit Delays Entry DelayExit Delay Entry/Exit Delays cont’d Exit AlarmsExit Error Conditions Using the ∗ Key to Display and Announce System Status To turn the Voice Status feature on/off #Checking For Open Zones Away Mode Arms Entire System, Entry Delay On Instant Mode Arms Perimeter Only, Entry Delay OffMaximum Mode Arms Entire System, Entry Delay Off Arming the SystemMode Press these keys… Keypad Confirms By… Arming CommandsArming the System cont’d Quick ArmingSingle Button Arming Single Button Step ArmingKey First Press Second Press Third Press Using the Keyswitch KeyswitchTo arm in the Away mode To arm in the Stay modeUsing the OFF key Disarming and Silencing AlarmsBypassing Protection Zones Using the Bypass KeyQuick Bypass Bypassing Protection Zones cont’dChime Mode Using the Chime ModeUsing the Voice Chime Setting the Date and Time Date and TimeViewing the Current Date and Time This Function Sends This Signal With This Sounding… Using Panic KeysPanic Keys To activate a Panic FunctionAbout Macro Keys Macro Key Programming & UsageUsing a Programmed Macro Key Macro Key Programming & Usage cont’dExample of Macro Programming About Device Commands Using Device CommandsTo Activate Devices To Deactivate DevicesAbout Automatic Paging Paging FeaturePaging Feature cont’d About Manual PagingLatch Key Paging Security Codes & Authority Levels About Security CodesAuthority Level Definitions Security Codes & Authority Levels cont’d How to Assign Security Codes and AttributesAccessing Other Partitions About Accessing PartitionsGoto Command and Multi-Partition Arming Accessing Other Partitions cont’d Using the GoTo CommandMulti-Partition Arming Common Zone Operation About Scheduling SchedulingScheduling cont’d About Event Logging Event Logging ProceduresViewing the Event Log Understanding the Type of Event DisplayedSTAY/INSTANT Event Logging Procedures cont’dAbout Testing the System Testing the SystemTrouble Conditions If there are wireless sensors* in your system, the CheckTrouble Conditions cont’d Alarm 1xx Fault 1xx CheckRcvr Jam Or CheckOr no AC Busy-StandbyLong Rng Trbl Maintaining Your System This Section Applies only to Residential Systems Fire Alarm SystemFire Alarm System cont’d Individual KeysOr Key Pairs Kitchen Dining Emergency Evacuation Quick Guide to Basic System Functions Function Procedure CommentsFixed-Word Display Keypads Summary of Audible/Visual NotificationsAlpha Display Keypads Summary of A/V Notifications cont’dRegulatory Statements and Warnings FCC PartIndustry Canada Regulatory Statements cont’d Ringer Equivalence Number NoticeIndustrie Canada System Features Log User Setup System Features Log cont’dPaging Setup User Setup cont’dList of Output Devices OWNER’S Insurance Premium Credit Request Cont Page Page Limitations of this System ÊK14490V1Š