Honeywell VISTA-21IPSIA manual About Scheduling

Page 37

Scheduling

About Scheduling

The system provides to 16 end-user schedules (programmable by master/installer only), which can control various types of events.

•Each schedule causes a defined event to start and stop (when appropriate) at a specified time.

•Schedules can be set to automatically repeat at various intervals.

•Schedules can be set for random starting, if desired.

	Creating Schedules		Alpha Displays:
	1.	+ [#] + [6] [4]
	1.	+ [#] + [6] [4]	1 DISARMED
	(Master Code)		1 DISARMED
	(Master Code)		READY TO ARM
			READY TO ARM

2.Enter a 2-digit schedule number from: 01-16.

Press [∗] to continue.	ENTER SCHED NO.
	00=QUIT	00

3.Enter the desired 2-digit event number from the list: 00 = clear the scheduled event

01 = turn a programmed output on or off

ENTER EVENT
CLEAR EVENT	00

(see Using Device Commands section for a list of output device numbers used in your system)

02 = set a user access schedule for one or more users

(see Security Codes section for an explanation of access groups)

03 = send a “latch-key” report to a pager if the system is not disarmed by a specified time; message sent is “777-7777.”

04 = automatically arm the system in STAY mode at a specified time

05 = automatically arm the system in AWAY mode at a specified time 06 = automatically disarm the system at a specified time

07 = Display the word “REMINDER” at a specified time (if selected, the keypad beeps every 30 seconds beginning when the word “REMINDER” is first displayed, and the display alternates with the normal keypad display about every 4-5 seconds. To stop the beeps and cancel the display once it starts, press any key).

Press [∗] to continue.

4.For event number “01,” enter the output number associated with this schedule.

Otherwise, this prompt is skipped.

Press [∗] to continue to the “Start” prompt shown on the next page.

RELAY NUMBER

00

– 37 –

Image 37

Contents Ademco Vista Series About This Manual Table of Contents Table of Contents Introduction System OverviewSystem Basics System Overview cont’d Paging Feature Using the Voice Message Center if Voice Keypad is installedFunction Keys SchedulingGeneral Information About The KeypadsArmed Ready Message MIC About The Keypads cont’dFIXED-WORD Display Keypad Armed Ready Message MIC Functions of the KeypadsFunctions of the Keypads cont’d MIC Entry Delay Entry/Exit DelaysExit Delay Exit Alarms Entry/Exit Delays cont’dExit Error Conditions To turn the Voice Status feature on/off # Using the ∗ Key to Display and Announce System StatusChecking For Open Zones Away Mode Arms Entire System, Entry Delay On Instant Mode Arms Perimeter Only, Entry Delay OffMaximum Mode Arms Entire System, Entry Delay Off Arming the SystemMode Press these keys… Keypad Confirms By… Arming CommandsArming the System cont’d Quick ArmingSingle Button Step Arming Single Button ArmingKey First Press Second Press Third Press Using the Keyswitch KeyswitchTo arm in the Away mode To arm in the Stay modeUsing the OFF key Disarming and Silencing AlarmsBypassing Protection Zones Using the Bypass KeyQuick Bypass Bypassing Protection Zones cont’dUsing the Chime Mode Chime ModeUsing the Voice Chime Date and Time Setting the Date and TimeViewing the Current Date and Time This Function Sends This Signal With This Sounding… Using Panic KeysPanic Keys To activate a Panic FunctionAbout Macro Keys Macro Key Programming & UsageMacro Key Programming & Usage cont’d Using a Programmed Macro KeyExample of Macro Programming About Device Commands Using Device CommandsTo Activate Devices To Deactivate DevicesAbout Automatic Paging Paging FeatureAbout Manual Paging Paging Feature cont’dLatch Key Paging About Security Codes Security Codes & Authority LevelsAuthority Level Definitions Security Codes & Authority Levels cont’d How to Assign Security Codes and AttributesAbout Accessing Partitions Accessing Other PartitionsGoto Command and Multi-Partition Arming Using the GoTo Command Accessing Other Partitions cont’dMulti-Partition Arming Common Zone Operation About Scheduling SchedulingScheduling cont’d About Event Logging Event Logging ProceduresViewing the Event Log Understanding the Type of Event DisplayedSTAY/INSTANT Event Logging Procedures cont’dAbout Testing the System Testing the SystemTrouble Conditions If there are wireless sensors* in your system, the CheckTrouble Conditions cont’d Alarm 1xx Fault 1xx CheckRcvr Jam Or CheckBusy-Standby Or no ACLong Rng Trbl Maintaining Your System This Section Applies only to Residential Systems Fire Alarm SystemIndividual Keys Fire Alarm System cont’dOr Key Pairs Kitchen Dining Emergency Evacuation Quick Guide to Basic System Functions Function Procedure CommentsFixed-Word Display Keypads Summary of Audible/Visual NotificationsAlpha Display Keypads Summary of A/V Notifications cont’dFCC Part Regulatory Statements and WarningsIndustry Canada Ringer Equivalence Number Notice Regulatory Statements cont’dIndustrie Canada System Features Log User Setup System Features Log cont’dPaging Setup User Setup cont’dList of Output Devices OWNER’S Insurance Premium Credit Request Cont Page Page Limitations of this System ÊK14490V1Š