Honeywell VISTA-21IPSIA manual ÊK14490V1Š

Page 64

TWO YEAR LIMITED WARRANTY

Honeywell International Inc., acting through its Security & Communications business (“Seller”), 2 Corporate Center Drive, Melville, New York 11747 warrants its products to be free from defects in materials and workmanship under normal use and service, normal wear and tear excepted, for 24 months from the manufacture date code; provided, however, that in the event the Buyer presents a proper invoice relating to the purchased product and such invoice bears a date later than the manufacture date, then Seller may at its discretion, reflect the warranty period as commencing at invoice date. Except as required by law, this Limited Warranty is only made to Buyer and may not be transferred to any third party. During the applicable warranty period, Seller will repair or replace, at its sole option and as the exclusive remedy hereunder, free of charge, any defective products.

Seller shall have no obligation under this Limited Warranty or otherwise if the product:

(i)is improperly installed, applied or maintained;

(ii)installed outside of stated operating parameters, altered or improperly serviced or repaired by anyone other than the Seller/Seller’s Authorized Service/Repair Center;

(iii)damage is caused by outside natural occurrences, such as lightning, power surges, fire, floods, acts of nature, or the like; or

(iv)defects result from unauthorized modification, misuse, vandalism, alterations of serial numbers, other causes unrelated to defective materials or workmanship, or failures related to batteries of any type used in connection with the products sold hereunder.

Exceptions to Warranty With Respect to Honeywell Products listed below:

Hardwire Contacts and PIRs – Seller warrants parts for hardwire contacts and PIRs in accordance with the terms of the above limited warranty for a period of five (5) years from the manufacture date code.

EXCLUSION OF WARRANTIES, LIMITATION OF LIABILITY

THERE ARE NO WARRANTIES OR CONDITIONS, EXPRESS OR IMPLIED, OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. TO THE FULL FULLEST EXTENT PERMITTED BY LAW, IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY (i)

CONSEQUENTIAL, INCIDENTAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES ARISING OUT OF OR RELATING IN ANY WAY TO THE PRODUCT AND/OR FOR BREACH OF THIS OR ANY OTHER WARRANTY OR CONDITION, EXPRESS OR IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER, EVEN IF THE LOSS OR DAMAGE IS CAUSED BY SELLER’S OWN NEGLIGENCE OR FAULT AND EVEN IF SELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH LOSSES OR DAMAGES. Any product description (whether in writing or made orally by Seller or Seller’s agents), specifications, samples, models, bulletin, drawings, diagrams, engineering sheets or similar materials used in connection with the Buyer’s order are for the sole purpose of identifying the Seller’s products and shall not be construed as an express warranty or condition. Any suggestions by Seller or Seller’s agents regarding use, applications, or suitability of the products shall not be construed as an express warranty or condition unless confirmed to be such in writing by Seller. Seller does not represent that the products it sells may not be compromised or circumvented; that the products will prevent any personal injury or property loss by burglary, robbery, fire or otherwise, or that the products will in all cases provide adequate warning or protection. Buyer understands that a properly installed and maintained alarm may only reduce the risk of a burglary, robbery or fire without warning, but it is not insurance or a guarantee that such will not occur or will not cause or lead to personal injury or property loss. CONSEQUENTLY, SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY DAMAGE ORF OTHER LOSS BASED ON ANY CLAIM AT ALL INCLUDING A CLAIM THE PRODUCT FAILED TO GIVE WARNING. However, if Seller is held liable whether directly or indirectly for any loss or damage with respect to the products it sells, regardless of cause or origin, its maximum liability shall not in any case exceed the purchase price of the product, which shall be fixed as liquidated damages and not as a penalty, and shall be the complete and exclusive remedy against the Seller. Should your product become defective during the warranty, please contact your installer to facilitate repair or replacement with Seller pursuant to the terms hereof. Seller reserves the right to replace any defective product under warranty with new, refurbished, or remanufactured product.

2 Corporate Center Drive, Suite 100

P.O. Box 9040

Melville, NY 11747

Copyright © 2007 Honeywell International Inc.

www.honeywell.com/security

ÊK14490V1:Š

K14490V1 7/10 Rev. A

Image 64
Contents Ademco Vista Series About This Manual Table of Contents Table of Contents Introduction System OverviewSystem Basics System Overview cont’d Using the Voice Message Center if Voice Keypad is installed Paging FeatureFunction Keys SchedulingAbout The Keypads General InformationAbout The Keypads cont’d Armed Ready Message MICFIXED-WORD Display Keypad Functions of the Keypads Armed Ready Message MICFunctions of the Keypads cont’d MIC Entry Delay Entry/Exit DelaysExit Delay Exit Alarms Entry/Exit Delays cont’dExit Error Conditions To turn the Voice Status feature on/off # Using the ∗ Key to Display and Announce System StatusChecking For Open Zones Instant Mode Arms Perimeter Only, Entry Delay Off Away Mode Arms Entire System, Entry Delay OnMaximum Mode Arms Entire System, Entry Delay Off Arming the SystemArming Commands Mode Press these keys… Keypad Confirms By…Arming the System cont’d Quick ArmingSingle Button Step Arming Single Button ArmingKey First Press Second Press Third Press Keyswitch Using the KeyswitchTo arm in the Away mode To arm in the Stay modeDisarming and Silencing Alarms Using the OFF keyUsing the Bypass Key Bypassing Protection ZonesBypassing Protection Zones cont’d Quick BypassUsing the Chime Mode Chime ModeUsing the Voice Chime Date and Time Setting the Date and TimeViewing the Current Date and Time Using Panic Keys This Function Sends This Signal With This Sounding…Panic Keys To activate a Panic FunctionMacro Key Programming & Usage About Macro KeysMacro Key Programming & Usage cont’d Using a Programmed Macro KeyExample of Macro Programming Using Device Commands About Device CommandsTo Activate Devices To Deactivate DevicesPaging Feature About Automatic PagingAbout Manual Paging Paging Feature cont’dLatch Key Paging About Security Codes Security Codes & Authority LevelsAuthority Level Definitions How to Assign Security Codes and Attributes Security Codes & Authority Levels cont’dAbout Accessing Partitions Accessing Other PartitionsGoto Command and Multi-Partition Arming Using the GoTo Command Accessing Other Partitions cont’dMulti-Partition Arming Common Zone Operation Scheduling About SchedulingScheduling cont’d Event Logging Procedures About Event LoggingViewing the Event Log Understanding the Type of Event DisplayedEvent Logging Procedures cont’d STAY/INSTANTTesting the System About Testing the SystemIf there are wireless sensors* in your system, the Check Trouble ConditionsAlarm 1xx Fault 1xx Check Trouble Conditions cont’dRcvr Jam Or CheckBusy-Standby Or no ACLong Rng Trbl Maintaining Your System Fire Alarm System This Section Applies only to Residential SystemsIndividual Keys Fire Alarm System cont’dOr Key Pairs Kitchen Dining Emergency Evacuation Function Procedure Comments Quick Guide to Basic System FunctionsSummary of Audible/Visual Notifications Fixed-Word Display KeypadsSummary of A/V Notifications cont’d Alpha Display KeypadsFCC Part Regulatory Statements and WarningsIndustry Canada Ringer Equivalence Number Notice Regulatory Statements cont’dIndustrie Canada System Features Log System Features Log cont’d User SetupUser Setup cont’d Paging SetupList of Output Devices OWNER’S Insurance Premium Credit Request Cont Page Page Limitations of this System ÊK14490V1Š