Honeywell VISTA-21IPSIA manual Or no AC, Busy-Standby, Long Rng Trbl

Page 44

Trouble Conditions (cont’d)

Other Trouble	AC LOSS
Displays	(or NO AC)
(Continued)

The system is operating on battery power

only due to an AC power failure. If only some lights are out on the premises, check circuit breakers and fuses and reset or replace as necessary. If AC power cannot be restored and a “low system battery” message appears (see previous page), CALL FOR SERVICE.

Busy-Standby	If this message remains displayed for
(or dI)	more than 1 minute, system is disabled.
	CALL FOR SERVICE.

OPEN CIRCUIT	The keypad is not receiving signals from
(or OC)	the control. CALL FOR SERVICE.

Long Rng Trbl	If part of your system, back-up Long
(or bF)	Range Radio communication has failed.
	CALL FOR SERVICE.

TELCO FAULT	The telephone line has a problem.
(or CHECK 94)	CALL FOR SERVICE.

Total Power Failure If there is no keypad display at all, and the READY indicator is not lit, operating power (from AC and back-up battery) for the system

has been interrupted and the system is inoperative. CALL FOR

SERVICE.

In The Event Of Telephone Operational Problems

In the event of telephone operational problems, disconnect the control from the phone line by removing the plug from the phone wall jack. We recommend that your installer demonstrate this disconnection on installation of the system. Do not attempt to disconnect the phone connection inside the control. Doing so will result in the loss of your phone lines. If the regular phones work correctly after the control has been disconnected from the phone wall jack, the control has a problem and you should immediately call for service. If upon disconnection of the control, there is still a problem on the phone line, notify the Telephone Company that they have a problem and request prompt phone repair service. The user may not under any circumstances attempt any service or repairs to the security system. Repairs must be made only by authorized service (see the LIMITED WARRANTY statement for information on how to obtain service).

– 44 –

Image 44

Contents Ademco Vista Series About This Manual Table of Contents Table of Contents System Basics System OverviewIntroduction System Overview cont’d Using the Voice Message Center if Voice Keypad is installed Paging FeatureFunction Keys SchedulingAbout The Keypads General InformationAbout The Keypads cont’d Armed Ready Message MICFIXED-WORD Display Keypad Functions of the Keypads Armed Ready Message MICFunctions of the Keypads cont’d MIC Exit Delay Entry/Exit DelaysEntry Delay Exit Error Conditions Entry/Exit Delays cont’dExit Alarms Checking For Open Zones Using the ∗ Key to Display and Announce System StatusTo turn the Voice Status feature on/off # Instant Mode Arms Perimeter Only, Entry Delay Off Away Mode Arms Entire System, Entry Delay OnMaximum Mode Arms Entire System, Entry Delay Off Arming the SystemArming Commands Mode Press these keys… Keypad Confirms By…Arming the System cont’d Quick ArmingKey First Press Second Press Third Press Single Button ArmingSingle Button Step Arming Keyswitch Using the KeyswitchTo arm in the Away mode To arm in the Stay modeDisarming and Silencing Alarms Using the OFF keyUsing the Bypass Key Bypassing Protection ZonesBypassing Protection Zones cont’d Quick BypassUsing the Voice Chime Chime ModeUsing the Chime Mode Viewing the Current Date and Time Setting the Date and TimeDate and Time Using Panic Keys This Function Sends This Signal With This Sounding…Panic Keys To activate a Panic FunctionMacro Key Programming & Usage About Macro KeysExample of Macro Programming Using a Programmed Macro KeyMacro Key Programming & Usage cont’d Using Device Commands About Device CommandsTo Activate Devices To Deactivate DevicesPaging Feature About Automatic PagingLatch Key Paging Paging Feature cont’dAbout Manual Paging Authority Level Definitions Security Codes & Authority LevelsAbout Security Codes How to Assign Security Codes and Attributes Security Codes & Authority Levels cont’dGoto Command and Multi-Partition Arming Accessing Other PartitionsAbout Accessing Partitions Multi-Partition Arming Accessing Other Partitions cont’dUsing the GoTo Command Common Zone Operation Scheduling About SchedulingScheduling cont’d Event Logging Procedures About Event LoggingViewing the Event Log Understanding the Type of Event DisplayedEvent Logging Procedures cont’d STAY/INSTANTTesting the System About Testing the SystemIf there are wireless sensors* in your system, the Check Trouble ConditionsAlarm 1xx Fault 1xx Check Trouble Conditions cont’dRcvr Jam Or CheckLong Rng Trbl Or no ACBusy-Standby Maintaining Your System Fire Alarm System This Section Applies only to Residential SystemsOr Key Pairs Fire Alarm System cont’dIndividual Keys Kitchen Dining Emergency Evacuation Function Procedure Comments Quick Guide to Basic System FunctionsSummary of Audible/Visual Notifications Fixed-Word Display KeypadsSummary of A/V Notifications cont’d Alpha Display KeypadsIndustry Canada Regulatory Statements and WarningsFCC Part Industrie Canada Regulatory Statements cont’dRinger Equivalence Number Notice System Features Log System Features Log cont’d User SetupUser Setup cont’d Paging SetupList of Output Devices OWNER’S Insurance Premium Credit Request Cont Page Page Limitations of this System ÊK14490V1Š