White Rodgers G1N 4R9 manual Early Signs Of Overfired Furnace, Wood As Heating Fuel

Page 13

HEATING

HEATING

1.When loading the furnace, lower the kindled pieces of wood and place them at the center of the combustion chamber before adding new logs.

2.Do not overload. Air must circulate freely in the upper part of the furnace in order to obtain an efficient operation of the appliance. Please note that a small hot fire will produce much less residues than a large smouldering one.

IMPORTANT: DURING THE HEATING PROCESS, REMOVE THE ASHES AND WOOD THAT COULD OBSTRUCT THE 1/4" (6.4 mm) HOLE LOCATED BELOW THE DOOR INSIDE THE FURNACE.

PROCEDURE TO OPEN THE LOADING DOOR

TO MINIMIZE THE RISK OF A BACK DRAUGHT OPEN THE DOOR 1”

AND WAIT ABOUT 10 SECONDS BEFORE OPENING COMPLETELY.

THE PURPOSE IS TO STABILIZE THE PRESSURE INSIDE THE FURNACE.

EARLY SIGNS OF OVERFIRED FURNACE

1.Roaring fire.

2.Chimney connector is glowing red.

3.Extreme heat coming from the furnace. If this occurs, DO NOT OPEN THE DOOR, shut-off the air inlet opening completely, and wait until the glow has completely subsided.

ALWAYS KEEP THE DOOR AND THE ASH DRAWER CLOSED

(except for lighting and maintenance).

WOOD AS HEATING FUEL

We recommend that you burn dry wood only.

There are two important factors to be considered when choosing a type of wood: the moisture content and the wood density. Hardwood, such as maple, oak and beech will provide better results because of the high density and minimal tar produced during combustion. It is highly recommended to use wood that has been dried at least six months. Do not use coal as heating fuel in this appliance.

13

Image 13

Contents QuébecQuébec G1N 4R9 Stove Builder International Inc 1700, Léon-HarmelWOOD COMBINED ELECTRICTable of contents LIMITED LIFETIME WARRANTY 11. TROUBLESHOOTING12. DUCTS AND REGISTER MEASUREMENTS INTRODUCTION 2. SAFETY RULES1.CHIMNEY AND DRAFT GENERAL REQUIREMENTSTHEASH DRAWER GET VERY HOT W A R N I N GDONOT MANIPULATE WITH BARE HANDS ODOUR FROM THE PAINTThe drawer must be cleaned regularly 3. APPLIANCE INSTALLATIONSMOKE DETECTOR ASH DRAWERCLEARANCES TO COMBUSTIBLE MATERIALS PIPE CONNECTOR AND DAMPER24” both sides for PSG5000 WOOD FLUE PIPEUNPROPER INSTALLATION PROPER INSTALLATIONDAMPER COMBUSTION AIRELECTRICAL CONNECTION WARNING USE FEEDING WIRES SUITABLE FOR 75OCWOOD ONLY WOOD/ELECTRICWARNING USE FEEDING WIRES SUITABLE FOR 75OC Red button manual reset Thermodisk L-170ELECTRIC ELEMENT INSIDE VIEW OF THE ELECTRIC ELEMENTFAN CONTROL THERMOSTATOUTSIDE VIEW OF THE ELECTRIC ELEMENT Control system 4. OPERATING INSTRUCTIONSLIGHTING PREHEATINGexcept for lighting and maintenance PROCEDURE TO OPEN THE LOADING DOORHEATING EARLY SIGNS OF OVERFIRED FURNACELOCAL FIRE DEPARTMENT CHIMNEY FIRESMAINTENANCE OF THE EXCHANGERS 5. MAINTENANCEMAINTENANCE OF THE BLOWER MOTOR CHIMNEY MAINTENANCEDOOR GASKET MAINTENANCE 6. REPLACEMENT PARTSFILTERS GASKETWOOD-ONLYFURNACES 7. ELECTRIC DIAGRAMS FOR UNITS BUILT FROMTHERMINAL BOARD15 KW @ 30KW WOOD/ELECTRIC FURNACESBLOWER PSG5000 WOOD-ONLYFURNACES2 SPEED MOTOR20 KW @ 30KW PSG5000 WOOD/ELECTRIC FURNACES20 KW @ 30KW SWITCH 8. ELECTRIC DIAGRAMS FOR UNITS BUILT BEFOREWOOD ONLY FURNACES PSG BLOWERBLOWER WOOD ONLY FURNACES PSGMOTOR 1 SPEED15 KW @ 30KW WOOD/ELECTRIC FURNACES PSGWOOD/ELECTRIC FURNACES PSG 5000 40KW @ 60KW 20 KW @ 30KW COMMAND20 KW @ 30KW BOARD TERMINALWOOD ONLY FURNACES PSG BLOWER15 KW @ 30KW WOOD/ELECTRIC FURNACES PSG9. TECHNICAL SPECIFICATIONS COMMERCIAL AREA RESIDENTIAL AREAIMPORTANT NOTE 11. TROUBLESHOOTINGDAMPER 12. DUCTS AND REGISTER MEASUREMENTSExposed walls N.B. The main duct mustWARRANTY APPLICATION LIMITED LIFETIME WARRANTY1700, rue Léon-Harmel,Québec Québec G1N 4R9 tel. 418 527-3060fax