Axis Communications P5544 Multi-Connector Cable sold separately, Function Pin Specifications

Page 50

AXIS P5544 PTZ Dome Network Camera

Multi-Connector Cable (sold separately)

Multi-Connector Cable (sold separately)

When connecting external equipment to the Axis product, a multi-connector cable (available from Axis) is required in order to maintain the product’s IP rating. The multi-connector cable can be purchased from your Axis reseller.

Connect the multi-connector cable to the product’s multi-connector (see page 5 ). The cable provides the following connectors:

Note

See page 57 for technical specifications.

Power connector - 3-pin terminal block used for power input. See image below.

Audio in (pink) - 3.5 mm input for a mono microphone, or a line-in mono signal (left channel is used from a stereo signal).

Audio out (green) - 3.5 mm output for audio (line level) that can be connected to a public address (PA) system or an active speaker with a built-in amplifier. A pair of headphones can also be attached. A stereo connector must be used for the audio out.

I/O terminal connector - Use in applications for e.g. motion detection, event triggering, time lapse recording and alarm notifications. In addition to an auxiliary power and a GND pin, the I/O terminal connector provides the interface to:

•Digital output — For connecting external devices such as relays and LEDs. Connected devices can be activated by the VAPIX® Application Programming Interface, output buttons on the Live View page or by an Action Rule. The output will show as active (shown under System Options > Port & Devices > Port Status) if the alarm device is activated.

•Digital input — An alarm input for connecting devices that can toggle between an open and closed circuit, for example: PIRs, door/window contacts, glass break detectors, etc. When a signal is received the state changes and the input becomes active (shown under System Options > Port & Devices > Port Status).

Function

Pin

Notes

Specifications

 

 

 

 

GND

1

Ground

 

 

 

 

 

3.3 V DC Power

2

Can be used to power auxiliary equipment.

Max load = 250 mA

 

 

Note: This pin can only be used as power out.

 

 

 

 

 

Configurable

3–6

Digital input — Connect to GND to activate, or leave floating

0 to +40 V DC

(Input or Output)

 

(unconnected) to deactivate.

 

 

 

Digital output — Internal connection to ground when

Max load =100 mA

 

 

activated, floating (unconnected) when deactivated. If used

Max voltage = +40 V DC

 

 

with an external relay, a diode must be connected in parallel

 

 

 

with the load, for protection against voltage transients.

 

 

 

 

 

50

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Axis P5544 PTZ Dome Network Camera Liability SafetyAbout This Document Intellectual Property RightsTable of Contents Axis P5544 PTZ Dome Network CameraPerformance Considerations Hardware Overview ConnectorsHardware Overview For technical specifications, seeColor Indication LED IndicatorsMidspan LED Indicators Access from a Browser Accessing the ProductAccessing the Product Start a browser Internet Explorer, Firefox, SafariNetwork TCP/IP Advanced Access from the InternetSet the Root Password Click Create self-signed certificateOverview Mode Live ViewNormal Mode Audio Controls Go to Overview modeControls on the Live View To show the manual trigger buttons in the Live View Go to Setup EventsManual Trigger Media Streams How to Stream H.264Media Streams Axis Media Control AMCAlternative Methods of Accessing the Video Stream QuickTimeTM. The following paths can be usedAccessing Audio Streams Java applet supports simplex audio with G.711 encodingBasic Setup Setting Up the ProductSetting Up the Product Video Stream Video and AudioVideo and Audio Pixel CounterImage Click Save to apply the new settingsStream Profiles 264Image Appearance Camera SettingsExposure Settings White BalanceOverlay Image Image SettingsOverlay Go to Video & Audio Video Stream and select the Image tabAudio Modes Audio SettingsPrivacy Mask Audio InputAudio Output G711 G726Audio Clips Live View Config Default Viewer for BrowsersLive View Config User Defined Links Viewer SettingsGo to Setup Live View Config Output ButtonsAxis P5544 PTZ Dome Network Camera PTZ Pan Tilt Zoom Preset PositionsPTZ Pan Tilt Zoom GatekeeperAdvanced Guard TourOsdi Zones LimitsControls Operator Same as administrator but with lower priorityControl Queue Detectors Set Up Motion Detection WindowsDetectors Motion DetectionAudio Detection Motion Detection ParametersApplications ApplicationsEvents EventsGo to Events Action Rules and click Add Setting Up an Action RulePTZ Control Recurrences RecipientsSchedules Axis P5544 PTZ Dome Network Camera Recording List RecordingsRecordings Continuous RecordingAxis P5544 PTZ Dome Network Camera Security System OptionsSystem Options UsersAudio Support Date & TimeIeee IPv4 Address Configuration Basic TCP/IP SettingsNetwork IPv6 Address ConfigurationAdvanced TCP/IP Settings Link-Local IPv4 Address NAT traversal port mapping for IPv4QoS Quality of Service Smtp emailRTP/H.264 StorageUPnPTM BonjourGo to System Options Storage Click Network Share Network ShareGo to System Options Storage and click SD Card Ports MaintenancePorts & Devices Port StatusSupport Overview Open PTZ Calibration from System Options MaintenanceSupport System OverviewFile Upload Reset to Factory Default SettingsScripting Plain ConfigFunction Pin Specifications Multi-Connector Cable sold separatelyMulti-Connector Cable sold separately Connection diagram DC power inputEmergency Recovery Procedure TroubleshootingTroubleshooting Checking the FirmwareProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsProblems setting the IP address Product is accessible locally but not externally Problems with the H.264 formatPTZ problems Video and image problems, generalSetup Video & Audio Camera Settings Problems uploading filesMotion Detection triggers unexpectedly SettingsStorage and disk management problems No audioTechnical Specifications Technical SpecificationsConnectors Maintenance Installation aidsMemory Power Function/group Specifications Network SecurityPerformance Considerations Ver M1.15 Axis P5544 PTZ Dome Network Camera

P5544 specifications

The Axis Communications P5544 is a robust and versatile network camera designed for high-performance surveillance in various environments. With its advanced features and cutting-edge technologies, it provides exceptional video quality and reliability, making it a popular choice for businesses and organizations looking to enhance their security systems.

One of the standout features of the P5544 is its high-resolution imaging capabilities. The camera offers 720p HD video quality, ensuring clear and detailed footage, even in challenging lighting conditions. This high resolution is particularly beneficial for capturing essential details such as faces or license plates, which can be crucial in security scenarios.

The P5544 is equipped with a powerful zoom lens, allowing users to zoom in on specific areas of interest without compromising image quality. With a 22x optical zoom, operators can easily focus on distant subjects or wide scenes, providing flexibility in monitoring various locations. This feature, combined with the camera's pan and tilt functionality, enables comprehensive coverage of a designated area.

In addition to its impressive optical capabilities, the Axis P5544 incorporates advanced image enhancement technologies. It features Axis' Wide Dynamic Range (WDR) technology, which helps in handling difficult lighting conditions, such as bright sunlight and deep shadows. This ensures that video footage remains clear and detailed in various lighting scenarios, enhancing overall situational awareness.

The camera is designed for durability and adaptability, making it suitable for both indoor and outdoor use. It is housed in a rugged casing that meets IK10 vandal resistance standards, providing protection against physical damage. This robustness ensures that the camera can endure harsh weather conditions, making it a reliable option for various installations.

Moreover, the Axis P5544 supports Power over Ethernet (PoE), simplifying installation by requiring only a single cable for power and data transmission. This not only reduces the complexity of the setup but also contributes to a cleaner and more organized deployment.

In conclusion, the Axis Communications P5544 is a powerful surveillance tool that combines high-definition imagery, versatile zoom capabilities, advanced image processing, and a durable design. Its features make it an ideal choice for businesses seeking reliable security solutions that can adapt to various environments and challenges. With the P5544, organizations can enhance their monitoring capabilities, improving overall safety and security.
Top Page Image Contents