Bosch Appliances D9412GV2 manual Completing the Installation

Page 18

D9412GV2/D7412GV2 Operation and Installation Guide 4.0 Installation

4.6Completing the Installation

If not already complete, make the earth ground connection to Terminal 10 and lock the reset pin in the closed position.

4.6.1Charging the Battery

Connect the battery, then the transformer to allow the control panel to charge the battery while you complete the installation. Refer to Section 5.0 Power Supply on page 20 for instructions.

On-board Buzzer Sounds at Power Up and Reset: The system performs a series of self-diagnostic tests of hardware, software, and programming at power up and at reset. The buzzer on the control panel sounds during the tests. The self-diagnostics tests complete in approximately 1 to 3 seconds.

If the control panel fails any test, the buzzer continues sounding and a System Trouble message appears at the keypads. Refer to Problems Found during Self Diagnostics in the D9412GV2/D7412GV2/D7212GV2 Installation and Troubleshooting Quick Reference Guide (P/N: F01U003638) for a description of each system trouble message.

Touch Terminal 10 First: If the on-board buzzer sounds briefly when the control panel is touched, any static charge you carry discharges to the control panel.

Avoid electrostatic discharge. Always touch Terminal 10, the earth ground connection, before beginning work on the control panel.

If the control panel receives an electrostatic discharge, it might generate Watchdog Reset and Param Fail events. Refer to Watchdog Reset Reports in the D9412GV2/7412G/D7212GV2 Installation and Troubleshooting Quick Reference Guide

P/N: F01U003638) for a description of these events.

4.6.2Installing and Wiring Detection Devices

Install and wire detection devices and keypads at their locations throughout the premises. Do not connect the control panel yet.

Section 8.0 On-Board Points on page 31 contains instructions for wiring the on-board points to detection devices. Section 11.0 Arming Devices on page 53 contains instructions for wiring the keypads.

Instructions for wiring the off-board point POPIT sensor loops are found in the instructions packaged with the POPIT modules.

4.6.3Installing Modules and Relays

1.Power down the unit by unplugging the transformer and disconnecting the battery.

Always power down the unit when installing modules or relays, or when making wiring connections to the control panel.

2.Install and wire any modules required for the installation as described in the module’s installation instructions.

Instructions for the D8125 POPEX Module, D8128D OctoPOPIT Module, D8129 OctoRelay Module, D811 Arm Status Relay Module, and D928 Dual Phone Line Switcher appear in this guide.

Refer to Section 9.0 Off-Board Points on page 34 for D8125 and D8128D instructions. Refer to Section 10.0 Off-Board Relays on page 48 for D8129 and D811 instructions. Refer to Section 7.11 D928 Dual Phone Line Switcher on page 29 for D928 instructions.

3.If using the power outputs at Terminals 7 or 8, install a D136 relay in the appropriate sockets. Refer to Section Programmable Power Output Terminals 6, 7, and 8 on page 25 for instructions.

4.6.4Connecting the On-board Points and Keypads

Connect the on-board points and keypad wiring to the system. Refer to Section 8.0 On-Board Points on page 31 and Section 11.0 Arming Devices on page 53 for instructions.

4.6.5Powering Up

Reconnect the battery, then plug in the transformer. The buzzer sounds for 2 seconds when the control panel is powered up. Leave the reset pin in the locked position.

Yellow Charging Status LED Remains Lit: If the yellow charging status LED remains lit after five minutes of powering up the control panel, either the battery is deeply discharged or too many powered devices were connected to the control panel. Combined continuous current draw for Terminals 3, 8, 24, and 32, and the accessory connector cannot exceed

1.4A. Refer to Section 6.0 Power Outputs on page 25 for help.

18

Bosch Security Systems, Inc. 5/05 F01U003641B

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Operation and Installation Guide D9412GV2/D7412GV2Listings and Approvals TrademarksCertifications and Approvals Federal Communications Commission FCC RulesBosch Security Systems, Inc /05 F01U003641B Contents D9412GV2/D7412GV2 Operation and Installation Guide Figures TablesIntroduction Related DocumentationPrecautions during Installation Lightning StrikesEffects Configuration and Parts OverviewGV2 Series Control Panel Differences Literature Pack Parts ListAssembly Parts Available by Separate OrderAccessories Compatible AccessoriesFeatures in the D9412GV2 and D7412GV2 Ground Fault Detection KeyswitchAccess Control Ground Fault Detection Added FeatureOther Features NetCom FunctionsProgramming Enclosure Options InstallationInstallation Preparation Mounting EnclosureTerminals to earth ground Ground Fault Detect Enable Installing the Control PanelConnecting Earth Ground Terminal4 D9412GV2 and D7412GV2 Ground Fault Specifications Enabling Ground Fault DetectionGround Fault Detection Status Ground Fault ImpedanceCompleting the Installation Installing the Point Chart Label Testing the SystemProgramming the Control Panel Power Supply Primary Power Terminals 1Secondary Power Terminals Installing the Battery Non-Power-Limited Wiring Replacing the BatteryBattery Supervision Battery Charging Circuit Float ChargeBattery Discharge and Recharge Schedule Charging Status and Low Battery LEDs Continuous Power Output Terminals 24, Power OutputsTotal Available Power Programmable Power Output Terminals 6, 7,Verification/Reset Relay Available PowerFire System Power Formula Terminals 6Notification Telephone ConnectionsRegistration LocationDialing Format Phone LED RedOperation Monitor LED Green Telephone Line Monitor11 D928 Dual Phone Line Switcher DescriptionOperation AC Power LED Installing the D928 MountingWiring Telephone ConnectionsPoint Sensor Loops On-Board PointsTerminals 11 to 22 Description Point ParametersPoint Response Time 3 4 5 Off-Board Points Point Zonex Bus D9412GV2 Terminals and D7412GV2 Terminals5 D9412GV2/D7412GV2 Responses to Missing Point Conditions Off-Board Point ErrorsD8125, D8127 and D9127 Popit Modules ListingsConnecting the D8125 Popex to the D9412GV2 Control Panel Connecting the D8125 Popex to the D7412GV2 Panel Wiring POPITs to the Data Expansion Loop Installing the D8125 Popex ModuleWiring the D8125 to the Control Panel Data Expansion Loop Wire SpecificationsWiring Data Expansion Loops to Popex Modules Popit Sensor LoopsPopit Module Point Assignments D8128D OctoPOPIT Module Installation Setting the OctoPOPIT SwitchesAddress Switches Wiring OctoPOPITs D8128D OctoPOPIT Switch Settings for D9412GV2 and D7412GV2Point DIP Switches Mounting OctoPOPITsUsing the Terminal Strip Terminal Strip ConnectionsConnecting D8128D OctoPOPITs to the D9412GV2 First address on Zonex Bus Sensor loops Using Molex Connectors OctoPOPIT Sensor LoopsTesting Off-Board Points D8128D OctoPOPIT Sensor LoopsOff-Board Relays 10.1 D8129 OctoRelayRelay outputs can activate when you are Configuring the D8129 OctoRelayD8129 OctoRelay Switch Settings Setting the OctoRelay switches or10.2 D811 Arm Status Relay Module Wiring ConnectionsOutputs when you perform this function Number of D8128Ds Used with D8129sD811 for Relay On-board points D811 for Relay Arming Devices DescriptionKeypad Terminals 29 to Wire Limits for Individual Keypads Extra Power for More KeypadsKeyswitch Maintained ContactMomentary Contact Silencing the Bell12.3 D9131A Parallel Printer Interface Module InstallationSDI Devices 12.4 D9210B Wiegand Control Interface ModuleAddress Settings AccessAddress Switch Settings for Access Control Module SDI AddressUsed as an External Modem Connecting the D9133DC12.6.1 D9133DC Direct Connect Programming Module Network Interface ModulesDX4020 DIP Switch Settings Programmer Access Reports Programmer and Accessory ConnectionsProgrammer Connector Accessory ConnectorFaceplates 14.1 D9412GV2 Faceplate14.2 D7412GV2 Faceplate D7412GV2Appendix a System Wiring Diagrams, Issue a D9412GV2 Control PanelD9412GV2 Popex D7412GV2, Power Supply Side D7412GV2 Control PanelD7412GV2, Input Points and Peripheral Devices UL Smoke Detector Compatibility P/N 33284 forD7412GV2, SDI Devices Appendix B Point Address Charts Zonex 1 Point Address ChartZonex 2 Point Address Chart Zonex 2, Points 129 to 247 D9412GV2 OnlySpecifications D9412GV2/D7412GV2 Program Entry Guide P/N F01U003636Bosch Security Systems, Inc /05 F01U003641B Bosch Security Systems F01U003641B
Related manuals
Manual 158 pages 17.38 Kb

D9412GV2 specifications

The Bosch D9412GV2 is an exceptional dishwasher that stands out in the competitive world of home appliances. Known for its reliability and advanced features, this model offers a blend of cutting-edge technology and user-friendly design that appeals to modern households.

One of the most noteworthy features of the D9412GV2 is its impressive cleaning performance. Boasting a unique combination of powerful jets and specialized wash cycles, it ensures that even the toughest stains are removed effectively. The dishwasher features Bosch’s patented PrecisionWash system, which utilizes intelligent sensors to monitor the wash cycle’s progress and adjust the water spray for optimal cleaning results. This not only guarantees sparkling dishes but also conserves water and energy.

In terms of capacity, the D9412GV2 does not disappoint. It has a spacious interior that is designed to accommodate up to 16 place settings, making it an ideal choice for families or those who frequently entertain guests. The adjustable racks and flexible loading options allow users to maximize space and customize the dishwasher to suit their unique needs. The third rack is particularly useful for utensils and smaller items, providing additional space that enhances efficiency.

The dishwasher is also engineered with noise reduction features for a quieter operation. With a sound rating of 44 decibels, it operates silently in the background, allowing for uninterrupted conversations and a peaceful home environment. This is especially beneficial for open-concept living spaces.

Energy efficiency is another hallmark of the Bosch D9412GV2. It is Energy Star certified, reflecting its commitment to sustainable practices. It uses less water and electricity without compromising performance, making it a responsible choice for eco-conscious consumers.

Moreover, the presence of the Home Connect feature allows users to control and monitor their dishwasher remotely via a smartphone app. This innovative technology enables users to start or stop cycles, receive notifications, and even download new wash programs, adding convenience and flexibility to busy lifestyles.

In conclusion, the Bosch D9412GV2 is a state-of-the-art dishwasher that excels in cleaning performance, capacity, and energy efficiency. With its innovative technologies and thoughtful design, it represents Bosch's commitment to quality and customer satisfaction, making it a valuable addition to any kitchen.
Top Page Image Contents