Bosch Appliances D9412GV2 manual Installing the D928 Mounting, Wiring, Telephone Connections

Page 30

D9412GV2/D7412GV2 Operation and Installation Guide 7.0 Telephone Connections

7.11.3Installing the D928 Mounting

Mount the D928 on the lower right side of the enclosure using the screws provided with the switcher.

Wiring

The D928 has two flying leads. The green lead monitors AC power. The black lead is the ground reference for the AC Power LED.

1.Connect the green lead from the D928 to Terminal 1.

2.Connect the black lead from the D928 to Terminal 9.

Telephone Connections

1.Plug one end of the ribbon cable provided into J4 on the control panel. Plug the other end of the ribbon cable into the ACCESSORY connector on the control panel.

2.Plug one end of the D162 phone cord provided into the telco jack. Plug the other end of the phone cord into the telco jack on the control panel. Refer to Error! Reference source not found. for phone cord lengths.

Table 9: Phone Cord Lengths

 

 

Phone Cord

Length

D161

2.4 m (8 ft)

D162

61 cm (2 ft)

3.Plug one end of a D161 or D162 phone cord into J1 on the control panel. Plug the other end of the phone cord into the RJ31X or RJ138X for the primary telephone line.

4.Plug one end of a D161 or D162 phone cord into J2 on the control panel. Plug the other end of the phone cord into the RJ31X or RJ138X for the secondary telephone line. Refer to Error! Reference source not found. for phone cord lengths.

If you installed a D928 before November 19, 2001 on a D9412GV2 or D7412GV2, disconnect AC power from the control panel (battery must remain connected) and observe the green LED.

If this LED glows dimly, contact Customer Service at (800)289-0096 for a replacement module at no charge.

7.11.4 D928 Status LEDs

Four LEDs mounted on the front edge of the D928 Module show the status of AC power for the control panel, the status of the two telephone lines, and communication failure (Figure 11 on page 33). When programmed and operating normally, only the green AC power status LED is lit.

AC Power LED

The green AC Power Status LED lights when AC power is applied to Terminals 1 and 2 on the control panel.

Phone Line Fail LEDs

Two yellow Phone Line Status LEDs (one for the primary telephone line, one for the secondary telephone line) light if the voltage on the telephone line falls to between 5.0 and 7.0 VDC, without the corresponding current of 13 mA. The control panel monitors the faulty telephone line for the programmed interval before indicating a trouble condition. Refer to Section 7.8 Telephone Line Monitor on page 28 for a description of phone line monitor operation.

Communication Failure LED

The yellow Communication Failure LED lights when the system is in communication failure. The LED turns off when communication restores. Refer to Section 7.10 Communication Failure on page 28.

30

Bosch Security Systems, Inc. 5/05 F01U003641B

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Operation and Installation Guide D9412GV2/D7412GV2Listings and Approvals TrademarksCertifications and Approvals Federal Communications Commission FCC RulesBosch Security Systems, Inc /05 F01U003641B Contents D9412GV2/D7412GV2 Operation and Installation Guide Figures TablesIntroduction Related DocumentationPrecautions during Installation Lightning StrikesEffects Configuration and Parts OverviewGV2 Series Control Panel Differences Literature Pack Parts ListAssembly Parts Available by Separate OrderAccessories Compatible AccessoriesFeatures in the D9412GV2 and D7412GV2 Ground Fault Detection KeyswitchAccess Control Ground Fault Detection Added FeatureOther Features NetCom FunctionsProgramming Enclosure Options InstallationInstallation Preparation Mounting EnclosureTerminals to earth ground Ground Fault Detect Enable Installing the Control PanelConnecting Earth Ground Terminal4 D9412GV2 and D7412GV2 Ground Fault Specifications Enabling Ground Fault DetectionGround Fault Detection Status Ground Fault ImpedanceCompleting the Installation Installing the Point Chart Label Testing the SystemProgramming the Control Panel Power Supply Primary Power Terminals 1Secondary Power Terminals Installing the Battery Non-Power-Limited Wiring Replacing the BatteryBattery Supervision Battery Charging Circuit Float ChargeBattery Discharge and Recharge Schedule Charging Status and Low Battery LEDs Continuous Power Output Terminals 24, Power OutputsTotal Available Power Programmable Power Output Terminals 6, 7,Verification/Reset Relay Available PowerFire System Power Formula Terminals 6Notification Telephone ConnectionsRegistration LocationDialing Format Phone LED RedOperation Monitor LED Green Telephone Line Monitor11 D928 Dual Phone Line Switcher DescriptionOperation AC Power LED Installing the D928 MountingWiring Telephone ConnectionsPoint Sensor Loops On-Board PointsTerminals 11 to 22 Description Point ParametersPoint Response Time 3 4 5 Off-Board Points Point Zonex Bus D9412GV2 Terminals and D7412GV2 Terminals5 D9412GV2/D7412GV2 Responses to Missing Point Conditions Off-Board Point ErrorsD8125, D8127 and D9127 Popit Modules ListingsConnecting the D8125 Popex to the D9412GV2 Control Panel Connecting the D8125 Popex to the D7412GV2 Panel Wiring POPITs to the Data Expansion Loop Installing the D8125 Popex ModuleWiring the D8125 to the Control Panel Data Expansion Loop Wire SpecificationsWiring Data Expansion Loops to Popex Modules Popit Sensor LoopsPopit Module Point Assignments D8128D OctoPOPIT Module Installation Setting the OctoPOPIT SwitchesAddress Switches Wiring OctoPOPITs D8128D OctoPOPIT Switch Settings for D9412GV2 and D7412GV2Point DIP Switches Mounting OctoPOPITsUsing the Terminal Strip Terminal Strip ConnectionsConnecting D8128D OctoPOPITs to the D9412GV2 First address on Zonex Bus Sensor loops Using Molex Connectors OctoPOPIT Sensor LoopsTesting Off-Board Points D8128D OctoPOPIT Sensor LoopsOff-Board Relays 10.1 D8129 OctoRelayRelay outputs can activate when you are Configuring the D8129 OctoRelayD8129 OctoRelay Switch Settings Setting the OctoRelay switches or10.2 D811 Arm Status Relay Module Wiring ConnectionsOutputs when you perform this function Number of D8128Ds Used with D8129sD811 for Relay On-board points D811 for Relay Arming Devices DescriptionKeypad Terminals 29 to Wire Limits for Individual Keypads Extra Power for More KeypadsKeyswitch Maintained ContactMomentary Contact Silencing the Bell12.3 D9131A Parallel Printer Interface Module InstallationSDI Devices 12.4 D9210B Wiegand Control Interface ModuleAddress Settings AccessAddress Switch Settings for Access Control Module SDI AddressUsed as an External Modem Connecting the D9133DC12.6.1 D9133DC Direct Connect Programming Module Network Interface ModulesDX4020 DIP Switch Settings Programmer Access Reports Programmer and Accessory ConnectionsProgrammer Connector Accessory ConnectorFaceplates 14.1 D9412GV2 Faceplate14.2 D7412GV2 Faceplate D7412GV2Appendix a System Wiring Diagrams, Issue a D9412GV2 Control PanelD9412GV2 Popex D7412GV2, Power Supply Side D7412GV2 Control PanelD7412GV2, Input Points and Peripheral Devices UL Smoke Detector Compatibility P/N 33284 forD7412GV2, SDI Devices Appendix B Point Address Charts Zonex 1 Point Address ChartZonex 2 Point Address Chart Zonex 2, Points 129 to 247 D9412GV2 OnlySpecifications D9412GV2/D7412GV2 Program Entry Guide P/N F01U003636Bosch Security Systems, Inc /05 F01U003641B Bosch Security Systems F01U003641B
Related manuals
Manual 158 pages 17.38 Kb

D9412GV2 specifications

The Bosch D9412GV2 is an exceptional dishwasher that stands out in the competitive world of home appliances. Known for its reliability and advanced features, this model offers a blend of cutting-edge technology and user-friendly design that appeals to modern households.

One of the most noteworthy features of the D9412GV2 is its impressive cleaning performance. Boasting a unique combination of powerful jets and specialized wash cycles, it ensures that even the toughest stains are removed effectively. The dishwasher features Bosch’s patented PrecisionWash system, which utilizes intelligent sensors to monitor the wash cycle’s progress and adjust the water spray for optimal cleaning results. This not only guarantees sparkling dishes but also conserves water and energy.

In terms of capacity, the D9412GV2 does not disappoint. It has a spacious interior that is designed to accommodate up to 16 place settings, making it an ideal choice for families or those who frequently entertain guests. The adjustable racks and flexible loading options allow users to maximize space and customize the dishwasher to suit their unique needs. The third rack is particularly useful for utensils and smaller items, providing additional space that enhances efficiency.

The dishwasher is also engineered with noise reduction features for a quieter operation. With a sound rating of 44 decibels, it operates silently in the background, allowing for uninterrupted conversations and a peaceful home environment. This is especially beneficial for open-concept living spaces.

Energy efficiency is another hallmark of the Bosch D9412GV2. It is Energy Star certified, reflecting its commitment to sustainable practices. It uses less water and electricity without compromising performance, making it a responsible choice for eco-conscious consumers.

Moreover, the presence of the Home Connect feature allows users to control and monitor their dishwasher remotely via a smartphone app. This innovative technology enables users to start or stop cycles, receive notifications, and even download new wash programs, adding convenience and flexibility to busy lifestyles.

In conclusion, the Bosch D9412GV2 is a state-of-the-art dishwasher that excels in cleaning performance, capacity, and energy efficiency. With its innovative technologies and thoughtful design, it represents Bosch's commitment to quality and customer satisfaction, making it a valuable addition to any kitchen.
Top Page Image Contents