New Buck Corporation 1127B Lighting Instructions Modulating Valvemaxitrol, Operating Instructions

Page 24
OPERATING INSTRUCTIONS

OPERATING INSTRUCTIONS

Before operating this appliance, proceed through the following checklist

.

1.Read and understand these instructions before operating this appliance.

2.Check that there no leaks. If you smell gas do not attempt to light this appliance.

LIGHTING INSTRUCTIONS

MODULATING VALVE(MAXITROL)

FOR YOUR SAFETY, READ BEFORE LIGHTING

A.This appliance has a pilot which must be lighted by hand. When lighting the pilot, follow these instructions exactly.

B.BEFORE LIGHTING: Smell all around the appliance for gas. Be sure to smell next to the floor because gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

*Do not try to light any appliance.

*Do not touch any electrical switch; do not use any phone in your building.

*Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

*If you cannot reach your gas supplier, call your local fire department.

C.Use only your hand to push in or turn the gas control knob. Never use tools. If the knob will not push in or turn by hand, don’t try to repair it, call a qualified service technician. Force or attempted repair may result in fire or explosion.

D.Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water.

22

Image 24
Contents NEW BUCK CORPORATION MODEL 1127B VENT-FREEGAS HEATERManufacturer NEW BUCK CORPORATION P.O. Box 8000 Highway 226 South Spruce Pine, NCPage TABLE OF CONTENTS Page SAFETY INFORMATION WARNINGS Do not try to light any appliance 21. . ”WARNING Failure to keep the primary air openings of the burners clean may result in sooting and property damage.” PRODUCT IDENTIFICATION PRODUCT FEATURES UNPACKINGSAFETY DEVICE PIEZO IGNITION SYSTEMMINIMUM CLEARANCES TO COMBUSTIBLE CONSTRUCTION NOTE FOR GARAGE INSTALLATIONFor convenience and efficiency, install heater INSTALLATION 1.Wall Mounted2.Freestanding heater with optional pedestal 3.Freestanding with optional wooden mantelCLEANING INFORMATION FREESTANDING WITH OPTIONAL PEDESTAL INSTALLATION FREESTANDING OPTIONAL WOODEN MANTEL INSTALLATIONOPTIONAL “L” BRACKETS 2 AND SCREWS 2 PRO PRODUCING ADEQUATE VENTILATION DETERMINING FRESH-AIRFLOW FOR HEATER LOCATIONVent-freeheater VENTILATION AIR VENTILATION AIR FROM INSIDE BUILDINGVENTILATION AIR FROM OUTDOORS GAS CONNECTION FLAMECONNECTING TO A GAS SUPPLY Propane Supply TankExternal Regulator Vent Pointing Down Installation must include manual shutoff valve and plugged 1/2 NPT tap. Locate NPT tap within reach for test gauge hook-up.NPT tap must be upstream from unit GAS PRESSURE CHECK LOG PLACEMENT FOR Logs are shipped secured in unitFront View of Logs FOR YOUR SAFETY, READ BEFORE LIGHTING LIGHTING INSTRUCTIONS MODULATING VALVEMAXITROLOPERATING INSTRUCTIONS LIGHTING INSTRUCTIONS to IGNITE andfor “LOW” for “HIGH”TO TURN OFF GAS TO APPLIANCE IGNITER ELECTRODE THERMO-COUPLEO.D.S PILOT BURNER MANUAL LIGHTING PROCEDURE THERMOSTAT CONTROL OPERATIONFLAME CHECK BURNER FLAME PATTERN CORRECT FLAME PATTERN AT HIGH POSITIONFigure 1815 - Correct Burner Flame Pattern INCORRECT FLAME PATTERN AT HIGH POSITIONWIRING DIAGRAM POWER CORDMOTOR JUMPERTHERMOSTATREPAIR PARTS SERVICINGIMPORTANT SAFEGUARDS CLEANINGTROUBLE-SHOOTING PROBLEM SOLUTIONOBSERVED POSSIBLE1.Control knob is not fully pressed in Delayed ignition of burner 1. Heater produces a clinking TECHNICAL SERVICE MODEL 1127 - MODULATING VALVEPARTS LIST BLOWN UP VIEW OF HEATER, FAN MOTOR, AND ALL REMOVABLE PARTSPARTS LIST BURNER SYSTEMBLOWN UP VIEW OF BURNER ASSEMBLY LIMITED WARRANTY ON VENT-FREEGAS LOG HEATER NEW BUCK CORPORATION