New Buck Corporation
1127B
manual
Producing Adequate Ventilation
Troubleshooting
Install
Repair Parts
Parts list
Wiring Diagram
Connecting To A Gas Supply
Problem
Manual Lighting Procedure
Cleaning Information
Log Placement For
Page 15
Page 14
Page 16
Image 15
Page 14
Page 16
Contents
8000 Highway 226 South Spruce Pine, NC
NEW BUCK CORPORATION
MODEL 1127B VENT-FREEGAS HEATER
Manufacturer NEW BUCK CORPORATION P.O. Box
Page
TABLE OF CONTENTS
Page
SAFETY INFORMATION WARNINGS
Do not try to light any appliance
21. . ”WARNING Failure to keep the primary air openings of the burners clean may result in sooting and property damage.”
PRODUCT IDENTIFICATION
PIEZO IGNITION SYSTEM
PRODUCT FEATURES
UNPACKING
SAFETY DEVICE
MINIMUM CLEARANCES TO COMBUSTIBLE CONSTRUCTION
NOTE FOR GARAGE INSTALLATION
For convenience and efficiency, install heater
3.Freestanding with optional wooden mantel
INSTALLATION
1.Wall Mounted
2.Freestanding heater with optional pedestal
CLEANING INFORMATION
FREESTANDING OPTIONAL WOODEN MANTEL INSTALLATION
FREESTANDING WITH OPTIONAL PEDESTAL INSTALLATION
OPTIONAL “L” BRACKETS 2 AND SCREWS 2 PRO
DETERMINING FRESH-AIRFLOW FOR HEATER LOCATION
PRODUCING ADEQUATE VENTILATION
Vent-freeheater
VENTILATION AIR FROM INSIDE BUILDING
VENTILATION AIR
VENTILATION AIR FROM OUTDOORS
FLAME
GAS CONNECTION
CONNECTING TO A GAS SUPPLY
Propane Supply Tank
External Regulator Vent Pointing Down
Installation must include manual shutoff valve and plugged 1/2 NPT tap. Locate NPT tap within reach for test gauge hook-up.NPT tap must be upstream from unit
GAS PRESSURE CHECK
LOG PLACEMENT FOR
Logs are shipped secured in unit
Front View of Logs
FOR YOUR SAFETY, READ BEFORE LIGHTING
LIGHTING INSTRUCTIONS MODULATING VALVEMAXITROL
OPERATING INSTRUCTIONS
for “HIGH”
LIGHTING INSTRUCTIONS
to IGNITE and
for “LOW”
TO TURN OFF GAS TO APPLIANCE
IGNITER ELECTRODE THERMO-COUPLE
O.D.S PILOT BURNER
THERMOSTAT CONTROL OPERATION
MANUAL LIGHTING PROCEDURE
FLAME CHECK
INCORRECT FLAME PATTERN AT HIGH POSITION
BURNER FLAME PATTERN
CORRECT FLAME PATTERN AT HIGH POSITION
Figure 1815 - Correct Burner Flame Pattern
JUMPERTHERMOSTAT
WIRING DIAGRAM
POWER CORD
MOTOR
SERVICING
REPAIR PARTS
CLEANING
IMPORTANT SAFEGUARDS
TROUBLE-SHOOTING
POSSIBLE
PROBLEM
SOLUTION
OBSERVED
1.Control knob is not fully pressed in
Delayed ignition of burner
1. Heater produces a clinking
MODEL 1127 - MODULATING VALVE
TECHNICAL SERVICE
PARTS LIST
MOTOR, AND ALL REMOVABLE PARTS
BLOWN UP VIEW OF HEATER, FAN
BURNER SYSTEM
PARTS LIST
BLOWN UP VIEW OF BURNER ASSEMBLY
NEW BUCK CORPORATION
LIMITED WARRANTY ON VENT-FREEGAS LOG HEATER
Related pages
Troubleshooting for Cisco Systems 3750E
Specifications for Sylvania dbc840e
Error Message Cause Action for Brother DCP-375CW
COM Port Adapter Wiring and Signal Diagram for Enterasys Networks X16-C
To exit, press SET Menu when finished for Yamaha RX-V650
Installation suite for White Rodgers 8B43A-601
Replacement Parts List For Air Curtain Cabinets for Marley Engineered Products E4806-1125HFD
To call by searching for a contact using the keypad for Polycom CX500
Power on/off Menu for Samsung GH68-06534A
What are the common
dishdrawer fault codes
?
Top
Page
Image
Contents