New Buck Corporation 1127B manual Heater produces a clinking

Page 37

1. Heater produces a clinking/ 1.

IMPORTANT: Operating heater where impurities in the air exist may create odors. Cleaning supplies, paint, paint remover, cigarette smoke, cements and glues, new carpet or textiles, etc. create fumes. These fumes may mix with combustion air and create odor.

OBSERVED	POSSIBLE	SOLUTION
PROBLEM	CAUSE
1. Heater produces a clinking/ 1.	Metal expands while	1. This is common with most
ticking noise just after burner	heating or contracts while	heaters. If noise is
is lit or shut off	cooling.	excessive, contact a
		qualified service person.

2. Heater produces unwanted 1. Heater burning vapors

odorsfrom paint, hairspray, glues, etc. (See Important above)

2. Low fuel supply

3. Gas leak (See WARNING above)

1.Ventilate room. Stop using odor causing products while heater is running.

2.Refill supply tank.

3.Locate and control all leaks. See “Checking Gas Connections”.

3.	Heater shuts off in use	1.	Not enough fresh air is	1.	Open window/door for
	(ODS operates)		available.		ventilation
		2.	Low line pressure	2.	Contact local propane co.
		3.	ODS/Pilot is partially	3.	Clean ODS/Pilot
			clogged

4.	Gas odor even when control 1.		Gas leak (See	1.	Locate and correct all leaks
	knob is in “OFF” position		WARNING, above).		(see Checking Gas
		2.	Control valve defect		Connections)
		2.	Control valve defect	2.	Replace control valve
5.	Gas odor during combustion	1.	Foreign matter between	1.	Remove foreign matter
			control valve and burner		from gas tubing
		2.	Gas leak (See WARNING	2.	Locate and correct all leaks
			above).		(see “Checking Gas
					Connections”).

35

Image 37

Contents MODEL 1127B VENT-FREEGAS HEATER NEW BUCK CORPORATIONManufacturer NEW BUCK CORPORATION P.O. Box 8000 Highway 226 South Spruce Pine, NCPage TABLE OF CONTENTS Page SAFETY INFORMATION WARNINGS Do not try to light any appliance 21. . ”WARNING Failure to keep the primary air openings of the burners clean may result in sooting and property damage.” PRODUCT IDENTIFICATION UNPACKING PRODUCT FEATURESSAFETY DEVICE PIEZO IGNITION SYSTEMNOTE FOR GARAGE INSTALLATION MINIMUM CLEARANCES TO COMBUSTIBLE CONSTRUCTIONFor convenience and efficiency, install heater 1.Wall Mounted INSTALLATION2.Freestanding heater with optional pedestal 3.Freestanding with optional wooden mantelCLEANING INFORMATION FREESTANDING OPTIONAL WOODEN MANTEL INSTALLATION FREESTANDING WITH OPTIONAL PEDESTAL INSTALLATIONOPTIONAL “L” BRACKETS 2 AND SCREWS 2 PRO DETERMINING FRESH-AIRFLOW FOR HEATER LOCATION PRODUCING ADEQUATE VENTILATIONVent-freeheater VENTILATION AIR FROM INSIDE BUILDING VENTILATION AIRVENTILATION AIR FROM OUTDOORS FLAME GAS CONNECTIONPropane Supply Tank CONNECTING TO A GAS SUPPLYExternal Regulator Vent Pointing Down Installation must include manual shutoff valve and plugged 1/2 NPT tap. Locate NPT tap within reach for test gauge hook-up.NPT tap must be upstream from unit GAS PRESSURE CHECK Logs are shipped secured in unit LOG PLACEMENT FORFront View of Logs LIGHTING INSTRUCTIONS MODULATING VALVEMAXITROL FOR YOUR SAFETY, READ BEFORE LIGHTINGOPERATING INSTRUCTIONS to IGNITE and LIGHTING INSTRUCTIONSfor “LOW” for “HIGH”IGNITER ELECTRODE THERMO-COUPLE TO TURN OFF GAS TO APPLIANCEO.D.S PILOT BURNER THERMOSTAT CONTROL OPERATION MANUAL LIGHTING PROCEDUREFLAME CHECK CORRECT FLAME PATTERN AT HIGH POSITION BURNER FLAME PATTERNFigure 1815 - Correct Burner Flame Pattern INCORRECT FLAME PATTERN AT HIGH POSITIONPOWER CORD WIRING DIAGRAMMOTOR JUMPERTHERMOSTATSERVICING REPAIR PARTSCLEANING IMPORTANT SAFEGUARDSTROUBLE-SHOOTING SOLUTION PROBLEMOBSERVED POSSIBLE1.Control knob is not fully pressed in Delayed ignition of burner 1. Heater produces a clinking MODEL 1127 - MODULATING VALVE TECHNICAL SERVICEPARTS LIST MOTOR, AND ALL REMOVABLE PARTS BLOWN UP VIEW OF HEATER, FANBURNER SYSTEM PARTS LISTBLOWN UP VIEW OF BURNER ASSEMBLY NEW BUCK CORPORATION LIMITED WARRANTY ON VENT-FREEGAS LOG HEATER