Desa EFP33NRB Normal Lighting Instructions, Using Supplied Wall Switch Assembly, Control

Page 26

OPERATING FIREPLACE

Continued

NORMAL LIGHTING

INSTRUCTIONS

WARNING: You must oper- ate this heater with the fireplace screen in place. Make sure fire- place screen is in place before running heater.

NOTICE:Duringinitialoperationof new heater, burning logs will give off a paper-burning smell. Open damper or window to vent smell. This will only last a few hours.

1.STOP! Read the safety information on page 25.

2.Make sure equipment shutoff valve is fully open.

3.Wait five (5) minutes to clear out any gas. Smell for gas around heater and near floor. If you smell gas, STOP! Follow “B” on page 25. If you donʼt smell gas, go to the next step.

A. Using Supplied Wall Switch Assembly

1.Set manual ignition bypass switch on the control panel to the OFF position (auto- matic ignition position).

2.Press ON/OFF button. Hold for 6 seconds. Gas valve will open and electronic ignition will begin sparking to light pilot. LED will light. Note: You may be running this heater for the first time after connecting to gas sup- ply or at the start of your heating season. If so, the ON/OFF button may need to be pressed again. This will allow air to bleed from gas system. If several attempts to light pilot fail, contact a qualified service person or gas supplier for repairs. Until repairs are made, light and operate manually (see Manual Lighting Instructions for Electric Power Outage, page 27).

3.When pilot flame is lit, the thermocouple is heated by the flame. When thermocouple becomes hot (5 to 15 seconds), main burner will automatically light on high flame.

4.To lower flame, push HI/LO button on wall switch once. Note: This fireplace does not have a pilot-only mode.

CAUTION: Do not try to ad- just heating levels by using the equipment shutoff valve.

 

Manual Ignition Bypass Switch

HI/LO

(Up is for Remote Control)

 

 

Button

 

 

 

 

ON/OFF

 

 

Button

 

 

Wall

 

 

Switch

 

LED

Assembly

 

 

Figure 47 - Control Locations

Pilot

Manual Ignitor

Automatic

Electrode

Burner

 

Ignitor

 

 

 

 

Electrode

Figure 48 - Pilot (Natural Gas)

 

Manual Ignitor

 

Pilot

Electrode

Automatic

Burner

 

Ignitor

 

 

Electrode

Figure 49 - Pilot (Propane/LP Gas)

B. Using Hand-Held Wireless Remote

Control

 

 

1.Set manual ignition bypass switch on control panel to OFF position (automatic ignition position).

2.Wait five (5) minutes to clear out any gas. Smell for gas around heater and near floor. If you smell gas, STOP! Follow “B” on page 25, column 2. If you donʼt smell gas, go to the next step.

3.Point remote control toward the lower front of fireplace and push both buttons at the same time. Hold for 6 seconds. The gas valve will open and electronic igni- tion will begin sparking to light the pilot. Note: You will be able to hear a clicking sound during this process. LED on wall

switch will light.

26

www.desatech.com

111245-01B

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Shown with optional Hearth base accessory CGEFP33PRB, CGEFP33NRB EFP33PRB, EFP33NRBTable of Contents Safety Information Fireplace Floor Assembly Product IdentificationUnpacking Product FeaturesLocal Codes Determining FRESH-AIR Flow for Fireplace Location AIR for Combustion VentilationProviding Adequate Ventilation Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors InstallationCheck GAS Type Removing Fireplace Screen and Floor Assembly Installation ClearancesInstallation Sequence Electrical HookupFor Mantel Installation Electrical Connections for Power CordRelocating Wall Switch Assembly For Recessed Installation For Recessed FireplaceMounting Wall Switch Assembly to Side of Mantel Cutting LinesInstalling Variable Speed Blower Accessory Mounting Blower to FireboxLocation of Wiring Diagram Decal 3 from Blower Installing Thermostatic Blower Accessory Installing Switch and Cover Assembly and Speed ControlInstalling Bushings Operating the Blower Installing GAS Piping to Fireplace LocationInstallation Items Needed Propane/LP Connecting Fireplace to GAS SupplyNatural Test Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Checking GAS ConnectionsTest Pressures In Excess Of 1/2 Psig 3.5 kPa Conventional Fireplace Installation Pressure Testing Fireplace GAS ConnectionsBUILT-IN Fireplace Installation Nailing FlangesRough Opening for Installing Wall Installing Hood Top Brass Trim Side Brass Trim Adjusting Set ScrewsInstalling Logs Installing Back Log #1 Cgefp Logs ShownFor Your Safety Read Before Lighting Installing Battery Into RemoteInstalling Screen Operating FireplaceControl Using Supplied Wall Switch AssemblyNormal Lighting Instructions To Turn OFF GAS To Appliance Manual Lighting Instructions for Electrical Power OutageShutting Off Heater Wireless Remote Control Pilot Flame Pattern Inspecting BurnersOptional Blower Operation Main BurnerPilot AIR Inlet Hole Cleaning MaintenanceBurner Injector Holder LogsTroubleshooting Observed Problem Possible Cause RemedySee Cleaning and Mainte Gas leak. See Warning Statement aboveTechnical Service SpecificationsService Hints When Gas Pressure Is Too LowIllustrated Parts Breakdown Parts List Remote Control LOG Base AssemblyIllustrated Parts Breakdown KEY Part Number EFP33PRB EFP33NRB Description QTY Firebox Models CGEFP33PRB, CGEFP33NRB, EFP33PRB and EFP33NRB KEY Part Number Description QTY Replacement Parts AccessoriesHearth Base for USE with Cabinet Mantel Corner Mantel Accessory with Fireplace Perimeter TrimCorner Hearth Base for USE with Corner Mantel Wiring Diagram Templates This page Intentionally Left Blank Parts Central 111245-01B 111245-01B Not a UPC

EFP33NRB, CGEFP33PRB, CGEFP33NRB, EFP33PRB, EFP33NRB specifications

Desa offers a range of premium electric fireplaces with models such as EFP33NRB, CGEFP33PRB, CGEFP33NRB, EFP33PRB, and EFP33NRB, each designed to blend aesthetics with advanced heating technology. These electric fireplaces are renowned for their ability to create a warm ambiance without the hassle of traditional wood or gas fireplaces.

The EFP33NRB model, a part of Desa's electric fireplace collection, features a sleek design that fits seamlessly into various interior styles. With its realistic flame effect and adjustable brightness settings, users can customize their experience, enhancing any room while maintaining a cozy atmosphere. This model also incorporates energy-efficient LED technology, ensuring minimal power consumption without compromising on the visual appeal and comfort.

Similarly, the CGEFP33PRB and CGEFP33NRB are designed for those who appreciate the combination of style and functionality. These models offer a robust heating output, capable of warming larger spaces efficiently. The innovative heat management system also ensures even heat distribution, making these units suitable for year-round use. Additionally, remote control capabilities allow for effortless adjustment, enhancing user convenience.

The EFP33PRB features a modern framework that showcases the flames within a stylish casing. Its user-friendly interface includes touch controls and an easy-to-read display, allowing users to change settings with ease. The fireplace boasts a range of flame colors, allowing for personalization to match any decor or mood.

Across all these models, safety remains a top priority with built-in overheat protection and a tip-over switch, providing peace of mind during operation. Furthermore, the fireplaces operate quietly, ensuring an undisturbed environment while creating a warm, inviting space.

In conclusion, the Desa EFP33NRB, CGEFP33PRB, CGEFP33NRB, EFP33PRB, and EFP33NRB models represent the pinnacle of electric fireplace technology. With their modern designs, efficiency, and flexibility, they offer a perfect solution for anyone looking to enhance their living spaces with warmth and style. Whether for a contemporary home or a cozy cabin, these fireplaces promise to deliver both comfort and elegance.
Top Page Image Contents