Desa CGEFP33PRB, CGEFP33NRB, EFP33PRB, EFP33NRB Electrical Hookup, Installation Clearances

Page 9

INSTALLATION

Continued

WARNING: This appliance is equipped for (natural or pro- pane/LP) gas. Field conversion is not permitted.

ELECTRICAL HOOKUP

This fireplace normally operates under 120 VAC/60 Hz line voltage. The electrical cord sup- plied with your fireplace is five feet in length. You must locate fireplace within reach of a 120 volt grounded electrical outlet. If not, you must install an electrical outlet within reach of the fireplace power cord. The GA3555 outlet accessory may be used for built-in applications.

INSTALLATION CLEARANCES

WARNING: Maintain the minimum clearances. If you can, provide greater clearances from floor, ceiling and adjoining wall.

MINIMUM CLEARANCE TO

COMBUSTIBLE MATERIALS

Top

Left and

Bottom

 

Right Sides

and Rear

 

 

 

0"

16"

0"

Carefully follow the instructions below. This will ensure safe installation.

Minimum Clearances For Side

Combustible Material, Side Wall and

Ceiling

A.Clearances from the side of the fireplace cabinet to any combustible material and wall should follow diagram in Figure 5.

Example: The face of a mantel, bookshelf, etc. is made of combustible material and protrudes 3 1/2" from the wall. This combus- tible material must be 4" from the side of the fireplace cabinet (see Figure 5).

B.Clearances from the top of the fireplace open- ing to the ceiling should not be less than 42 inches.

Example

*

*Minimum 16 inches from Side Wall

Figure 5 - Minimum Clearance for

Combustible to Wall

INSTALLATION SEQUENCE

After unpacking fireplace (see Unpacking, page 4), we suggest that you install your fireplace system in the following sequence:

1.Removal of fireplace floor assembly (required)

2.Electrical connections for power cord (required)

3.Relocating wall switch (optional)

4.Installing blower accessory (optional)

5.Connecting fireplace to gas supply (required)

6.Checking gas connections (required)

7.Firebox installation, conventional or built-in (required)

8.Installing brass perimeter trim (optional)

9.Installing fireplace hood (required)

10.Installing logs (required)

11.Installing fireplace screen (required)

Use the following instructions to complete each step.

REMOVING FIREPLACE SCREEN AND FLOOR ASSEMBLY

NOTICE: Shutoff gas supply and disconnect heater from gas supply if installing blower into previously installed fireplace. Contact a qualified service per- son to do this.

1.Remove fireplace screen. Remove two screws that hold fireplace screen in place for shipping. These screws are located near top of screen. Discard screws. Lift fireplace screen up and pull out to remove.

2.If logs are installed, carefully remove the logs and set aside, noting the properly mounted location of each.

111245-01B

www.desatech.com

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents CGEFP33PRB, CGEFP33NRB EFP33PRB, EFP33NRB Shown with optional Hearth base accessoryTable of Contents Safety Information Product Identification Fireplace Floor AssemblyProduct Features Local CodesUnpacking AIR for Combustion Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation Air From Inside Building Ventilation AIRInstallation Check GAS TypeVentilation Air From Outdoors Installation Sequence Installation ClearancesRemoving Fireplace Screen and Floor Assembly Electrical HookupElectrical Connections for Power Cord Relocating Wall Switch AssemblyFor Mantel Installation For Recessed Fireplace For Recessed InstallationCutting Lines Mounting Wall Switch Assembly to Side of MantelMounting Blower to Firebox Installing Variable Speed Blower AccessoryLocation of Wiring Diagram Decal 3 from Blower Installing Switch and Cover Assembly and Speed Control Installing Thermostatic Blower AccessoryInstalling Bushings Installing GAS Piping to Fireplace Location Installation Items NeededOperating the Blower Connecting Fireplace to GAS Supply NaturalPropane/LP Checking GAS Connections Test Pressures In Excess Of 1/2 Psig 3.5 kPaTest Pressures Equal To or Less Than 1/2 Psig 3.5 kPa Pressure Testing Fireplace GAS Connections Conventional Fireplace InstallationNailing Flanges BUILT-IN Fireplace InstallationRough Opening for Installing Wall Top Brass Trim Side Brass Trim Adjusting Set Screws Installing HoodInstalling Back Log #1 Cgefp Logs Shown Installing LogsInstalling Screen Installing Battery Into RemoteFor Your Safety Read Before Lighting Operating FireplaceUsing Supplied Wall Switch Assembly Normal Lighting InstructionsControl Manual Lighting Instructions for Electrical Power Outage Shutting Off Heater Wireless Remote ControlTo Turn OFF GAS To Appliance Optional Blower Operation Inspecting BurnersPilot Flame Pattern Main BurnerBurner Injector Holder Cleaning MaintenancePilot AIR Inlet Hole LogsObserved Problem Possible Cause Remedy TroubleshootingSee Cleaning and Mainte Statement above Gas leak. See WarningService Hints SpecificationsTechnical Service When Gas Pressure Is Too LowIllustrated Parts Breakdown Remote Control LOG Base Assembly Parts ListIllustrated Parts Breakdown KEY Part Number EFP33PRB EFP33NRB Description QTY Firebox Models CGEFP33PRB, CGEFP33NRB, EFP33PRB and EFP33NRB KEY Part Number Description QTY Accessories Replacement PartsCorner Mantel Accessory with Fireplace Perimeter Trim Corner Hearth Base for USE with Corner MantelHearth Base for USE with Cabinet Mantel Wiring Diagram Templates This page Intentionally Left Blank Parts Central 111245-01B 111245-01B Not a UPC

EFP33NRB, CGEFP33PRB, CGEFP33NRB, EFP33PRB, EFP33NRB specifications

Desa offers a range of premium electric fireplaces with models such as EFP33NRB, CGEFP33PRB, CGEFP33NRB, EFP33PRB, and EFP33NRB, each designed to blend aesthetics with advanced heating technology. These electric fireplaces are renowned for their ability to create a warm ambiance without the hassle of traditional wood or gas fireplaces.

The EFP33NRB model, a part of Desa's electric fireplace collection, features a sleek design that fits seamlessly into various interior styles. With its realistic flame effect and adjustable brightness settings, users can customize their experience, enhancing any room while maintaining a cozy atmosphere. This model also incorporates energy-efficient LED technology, ensuring minimal power consumption without compromising on the visual appeal and comfort.

Similarly, the CGEFP33PRB and CGEFP33NRB are designed for those who appreciate the combination of style and functionality. These models offer a robust heating output, capable of warming larger spaces efficiently. The innovative heat management system also ensures even heat distribution, making these units suitable for year-round use. Additionally, remote control capabilities allow for effortless adjustment, enhancing user convenience.

The EFP33PRB features a modern framework that showcases the flames within a stylish casing. Its user-friendly interface includes touch controls and an easy-to-read display, allowing users to change settings with ease. The fireplace boasts a range of flame colors, allowing for personalization to match any decor or mood.

Across all these models, safety remains a top priority with built-in overheat protection and a tip-over switch, providing peace of mind during operation. Furthermore, the fireplaces operate quietly, ensuring an undisturbed environment while creating a warm, inviting space.

In conclusion, the Desa EFP33NRB, CGEFP33PRB, CGEFP33NRB, EFP33PRB, and EFP33NRB models represent the pinnacle of electric fireplace technology. With their modern designs, efficiency, and flexibility, they offer a perfect solution for anyone looking to enhance their living spaces with warmth and style. Whether for a contemporary home or a cozy cabin, these fireplaces promise to deliver both comfort and elegance.
Top Page Image Contents